NPH10S2403EI

NPH10S SERIES Isolated 10W Single Output DC-DC Converters SELECTION GUIDE Nominal Input Voltage Output Voltage Output Current Current Limit2 (Typ) Max Load Efficiency Capacitance Order Code1 NPH10S2403i NPH10S2405i NPH10S2412i NPH10S2415i NPH10S4803i NPH10S4805i NPH10S4812i NPH10S4815i (V) 24 24 24 24 48 48 48 48 (V) 3.4 5.1 12.1 15.1 3.4 5.1 12.1 15.1 (A) 2.94 1.96 0.83 0.67 2.94 1.96 0.83 0.67 (A) 4.5 3.0 1.2 1.1 4.1 2.8 1.2 1.0 (%) 79 83 86 86 80 83 86 87 (µF) 470 470 100 47 470 470 56 22 FEATURES ■ High Efficiency to 86% ■ Power Density up to 1.5kW/L (24W/in3 ) ■ 1.5kV Input to Output Isolation ■ Industry Standard Pinout ■ Surge Rating to 12W ■ Non Latching Current Limit ■ Fixed Frequency ■ Versatile Control Options ■ Continuous Rating to 10W at 72°C Without Heatsink ■ Operation to Zero Load ■ Protected Against Load Faults ■ Internal Over Temperature Protection ■ Uses No Electrolytic Capacitors ■ UL 94V-0 Package Materials DESCRIPTION The NPH10S series of DC-DC Converters combines ease of application with versatility. The pin pattern is based on the popular industry standard, but two additional pins may optionally be fitted to provide a variety of features not commonly found on units of this type. High efficiency enables full rating to be achieved in a small package without heatsinking. Thermally protected against sustained overload. The copper case achieves efficient heat transfer and screening. The product range has been recognised by Underwriters Laboratory (UL) to UL 1950 for operational insulation, file number E179522 applies. INPUT CHARACTERISTICS Parameter Conditions MIN NOM MAX Units Voltage Range Continuous operation, 24V input types Continuous operation, 48V input types3 18 36 24 48 36 75 V V OUTPUT CHARACTERISTICS Parameter Conditions MIN TYP MAX Units Voltage Set Point Error Overall Voltage Error Temperature Coefficient of Output Voltage (slope) Deviation of Output Voltage Line Regulation Load Regulation Ripple 50% load after 30 mins at nominal supply voltage Case temperature –40°C to 110°C Load 0% - 100% Input specified range Over any 10°C span within the specified temperature range Specified over temperature MIN-MAX Operating voltage range, 50% load 0% - 100% rated load4 rms 0.5 1 50 0.5 0.05 70 2.5 250 1 0.1 0.5 % % ppm°C % % % mV CONTROL CHARACTERISTICS Parameter Conditions MIN TYP MAX Units Voltage Trimming Range Remote Switch Input5 (voltage relative to input negative) At rated load, Trim control at either output Not operating Operating, open circuit voltage Time from application of valid input voltage to output being in specification Specified drive signal ±10 -15 9 0 10 25 320 330 350 440 395 1.5 11 % V mS kHz kHz Start Delay Synchronisation Switching Frequency 5 ABSOLUTE MAXIMUM RATINGS Input voltage, 24V input types Input voltage, 48V input types Output Voltage Output trim control Synchronisation/shutdown control –0.5V to 40V6 –0.5V to 80V6 –0.3V to controlled output voltage (operating or non-operating) –1V to +30V ±15V relative to input return ISOLATION CHARACTERISTICS Parameter Conditions MIN TYP MAX Units Isolation Voltage Resistance Capacitance Flash tested for 1 second Viso=500VDC 3.3V and 5V output 12V and 15V output 1500 1 50 90 VDC GΩ pF www.cdpoweronline.com 1 If optional pins ADJ and SS are required (as indicated in the pin connections diagram) prefix the ending “i” with an E when ordering, e.g. NPH10S4803Ei. 2 Current is quoted when output is 95% of regulated voltage. 3 For applications requiring UL1950 recognition, input voltage must not exceed 60VDC. 4 A minimum load of 10% of rating is recommended for typical applications ; see application notes. 5 Optional - Where fitted. 6 Absolute maximum value for 30 seconds. Prolonged operation may damage the product. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. NPH10S SERIES Isolated 10W Single Output DC-DC Converters ENVIRONMENTAL Parameter Conditions MIN TYP MAX Units THERMAL PERFORMANCE 15 Output Power (W) Case Temperature Storage Relative Humidity Thermal Protection Full load Absolute MAX internal temperature Non condensing 85°C Operates at case temperature –40 –40 110 110 125 85 °C °C % °C 2415 10 2405 2412 5 THERMAL CHARACTERISTICS MAX power rating with case temperature maintained by external means (eg forced air cooling) Case Temperature 2403 0 -40 -20 Ambient Temperature (°C) 0 20 40 60 80 100 120 Part Number NPH10S2403 NPH10S2405 NPH10S2412 NPH10S2415 NPH10S4803 NPH10S4805 NPH10S4812 NPH10S4815 100°C 10 10 10 12 10 10 12 12 105°C 7.0 8.2 9.5 9.5 7.0 4.7 8.0 7.5 110°C 2.3 3 4 4 1 1 0 0 Units Output Power (W) 15 W 10 4805 5 4815 4812 4803 W 0 -40 -20 Ambient Temperature (°C) 0 20 40 60 80 100 120 MECHANICAL DIMENSIONS 1.26 (32.00) BOTTOM VIEW 0.09 (2.34) 0.2 (5.08) 0.98 25.00 0.2(5.08) 0.39 (9.96) SS +VIN -VIN +V OUT 0.80 (20.32) ADJ 0V 0.2 (5.08) 0.39 (10.00) 1.78 (4.50) 0.15 (3.70) 0.23 (5.84) 0.8 20.32 0.04 (1.04) Ø 0.04 (0.90) Weight: 22g All dimensions in Inches (mm) ± 0.01 (0.25) All pins on a 0.10 (2.54) pitch and within ± 0.01 (0.25) of true position * Optional pins Case connected internally to 0V pin C&D Technologies (NCL) Limited reserve the right to alter or improve the specification, internal design or manufacturing process at any time, without notice. Please check with your supplier or visit our web site to ensure that you have the current and complete specification for your product before use. For information and instructions on use, please consult the NPH SERIES APPLICATION NOTES. © C&D Technologies (NCL) Limited 2003 NDC NPH10S.6 No part of this publication may be copied, transmitted or stored in a retrieval system or reproduced in any way including, but not limited to, photography, photocopy, magnetic or other recording means, without prior written permission from C&D Technologies (NCL) Limited. Instructions for use are available from www.cdpoweronline.com C&D Technologies (NCL) Ltd Tanners Drive, Blakelands North Milton Keynes MK14 5BU, England Tel: +44 (0)1908 615232 Fax: +44 (0)1908 617545 email: info@cdtechno-ncl.com www.cdpoweronline.com C&D Technologies Inc. 3400 E Britannia Drive, Tucson, Arizona 85706, USA Tel: +1 (800) 547-2537 Fax: +1 (520) 741-4598 email: sales@cdtechno.com