CAT24WC02PETE13F

CAT24WC01/02/04/08/16 1K/2K/4K/8K/16K-Bit Serial EEPROM FEATURES I 400 kHz I2C Bus Compatible* I 1.8 to 5.5Volt Operation I Low Power CMOS Technology I Write Protect Feature I Self-Timed Write Cycle with Auto-Clear I 1,000,000 Program/Erase Cycles I 100 Year Data Retention I 8-pin DIP, SOIC, TSSOP and MSOP packages - "Green" package option available I Commercial, Industrial, Automotive and — Entire Array Protected When WP at VIH I Page Write Buffer Extended Temperature Ranges DESCRIPTION The CAT24WC01/02/04/08/16 is a 1K/2K/4K/8K/16Kbit Serial CMOS EEPROM internally organized as 128/ 256/512/1024/2048 words of 8 bits each. Catalyst’s advanced CMOS technology substantially reduces device power requirements. The the CAT24WC01/02/04/ 08/16 feature a 16-byte page write buffer. The device operates via the I2C bus serial interface, has a special write protection feature, and is available in 8-pin DIP, SOIC, TSSOP and MSOP packages. PIN CONFIGURATION DIP Package (P, L, GL) A0 A1 A2 VSS 1 2 3 4 8 7 6 5 VCC WP SCL SDA BLOCK DIAGRAM SOIC Package (J, W, GW) EXTERNAL LOAD A0 A1 A2 VSS 1 2 3 4 8 7 6 5 VCC WP SCL SDA 5020 FHD F01 DOUT ACK VCC VSS WORD ADDRESS BUFFERS SENSE AMPS SHIFT REGISTERS COLUMN DECODERS TSSOP Package (U, Y, GY) MSOP Package (R, Z, GZ) A0 A1 A2 VSS 1 2 3 4 8 7 6 5 VCC WP SCL SDA (MSOP and TSSOP available for CAT24WC01, CAT24WC02 and CAT24WC04 only) SDA VCC WP SCL SDA WP START/STOP LOGIC A0 A1 A2 VSS 1 2 3 4 8 7 6 5 XDEC CONTROL LOGIC E2PROM PIN FUNCTIONS Pin Name A0, A1, A2 SDA SCL WP VCC VSS Function Device Address Inputs Serial Data/Address Serial Clock Write Protect +1.8V to +5.5V Power Supply Ground SCL A0 A1 A2 STATE COUNTERS SLAVE ADDRESS COMPARATORS HIGH VOLTAGE/ TIMING CONTROL DATA IN STORAGE * Catalyst Semiconductor is licensed by Philips Corporation to carry the I2C Bus Protocol. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias ................. –55°C to +125°C Storage Temperature ....................... –65°C to +150°C Voltage on Any Pin with Respect to Ground(1) ........... –2.0V to +VCC + 2.0V VCC with Respect to Ground ............... –2.0V to +7.0V Package Power Dissipation Capability (Ta = 25°C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(2) ........................ 100mA RELIABILITY CHARACTERISTICS Symbol NEND(3) TDR(3) VZAP(3) ILTH(3)(4) Parameter Endurance Data Retention ESD Susceptibility Latch-up Min. *COMMENT Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Max. Units Cycles/Byte Years Volts mA 1,000,000 100 2000 100 D.C. OPERATING CHARACTERISTICS VCC = +1.8V to +5.5V, unless otherwise specified. Limits Symbol ICC ISB (5) Parameter Power Supply Current Standby Current (VCC = 5.0V) Input Leakage Current Output Leakage Current Input Low Voltage Input High Voltage Output Low Voltage (VCC = 3.0V) Output Low Voltage (VCC = 1.8V) Min. Typ. Max. 3 1 10 10 Units mA µA µA µA V V V V Test Conditions fSCL = 100 KHz VIN = GND or VCC VIN = GND to VCC VOUT = GND to VCC ILI ILO VIL VIH VOL1 VOL2 –1 VCC x 0.7 VCC x 0.3 VCC + 0.5 0.4 0.5 IOL = 3 mA IOL = 1.5 mA CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V Symbol CI/O(3) CIN(3) Test Input/Output Capacitance (SDA) Input Capacitance (A0, A1, A2, SCL, WP) Max. 8 6 Units pF pF Conditions VI/O = 0V VIN = 0V Note: (1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC + 2.0V for periods of less than 20ns. (2) Output shorted for no more than one second. No more than one output shorted at a time. (3) These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. (4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V. (5) Maximum standby current (ISB ) = 10µA for the Automotive and Extended Automotive temperature range. Doc. No. 1022, Rev. N 2 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 A.C. CHARACTERISTICS VCC = +1.8V to +5.5V, unless otherwise specified. Read & Write Cycle Limits CAT24WCXX-1.8 1.8V-5.5V Symbol FSCL TI (1) CAT24WCXX 2.5V-5.5V Min. Max. 100 200 3.5 4.7 4 4.7 4 4.7 0 50 1.2 0.6 1.2 0.6 0.6 0 50 1 300 4 100 0. 6 100 0.3 300 4.5V-5.5V Min. Max. 400 200 1 Units kHz ns µs µs µs µs µs µs ns ns µs ns µs ns Parameter Clock Frequency Noise Suppression Time Constant at SCL, SDA Inputs SCL Low to SDA Data Out and ACK Out Time the Bus Must be Free Before a New Transmission Can Start Start Condition Hold Time Clock Low Period Clock High Period Start Condition Setup Time (for a Repeated Start Condition) Data In Hold Time Data In Setup Time SDA and SCL Rise Time SDA and SCL Fall Time Stop Condition Setup Time Data Out Hold Time Min. Max. 100 200 3.5 tAA tBUF (1) 4.7 4 4.7 4 4.7 0 50 1 300 4 100 tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF (1) (1) tSU:STO tDH Power-Up Timing(1)(2) Symbol tPUR tPUW Parameter Power-up to Read Operation Power-up to Write Operation Max. 1 1 Units ms ms Write Cycle Limits Symbol tWR Parameter Write Cycle Time Min. Typ. Max 10 Units ms The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address. Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 3 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 FUNCTIONAL DESCRIPTION The CAT24WC01/02/04/08/16 supports the I2C Bus data transmission protocol. This Inter-Integrated Circuit Bus protocol defines any device that sends data to the bus to be a transmitter and any device receiving data to be a receiver. Data transfer is controlled by the Master device which generates the serial clock and all START and STOP conditions for bus access. The CAT24WC01/ 02/04/08/16 operates as a Slave device. Both the Master and Slave devices can operate as either transmitter or receiver, but the Master device controls which mode is activated. A maximum of 8 devices (CAT24WC01 and CAT24WC02), 4 devices (CAT24WC04), 2 devices (CAT24WC08) and 1 device (CAT24WC16) may be connected to the bus as determined by the device address inputs A0, A1, and A2. PIN DESCRIPTIONS SCL: Serial Clock The CAT24WC01/02/04/08/16 serial clock input pin is used to clock all data transfers into or out of the device. This is an input pin. SDA: Serial Data/Address The CAT24WC01/02/04/08/16 bidirectional serial data/ address pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wire-ORed with other open drain or open collector outputs. A0, A1, A2: Device Address Inputs These inputs set device address when cascading multiple devices. When these pins are left floating the default values are zeros. A maximum of eight devices can be cascaded when Figure 1. Bus Timing tF tLOW SCL tSU:STA tHD:STA tHIGH tLOW tR tHD:DAT tSU:DAT tSU:STO SDA IN tAA SDA OUT 5020 FHD F03 tDH tBUF Figure 2. Write Cycle Timing SCL SDA 8TH BIT BYTE n ACK tWR STOP CONDITION START CONDITION ADDRESS 5020 FHD F04 Figure 3. Start/Stop Timing SDA SCL 5020 FHD F05 START BIT Doc. No. 1022, Rev. N STOP BIT 4 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 using either CAT24WC01 or CAT24WC02 device. All three address pins are used for these densities. If only one CAT24WC01 or CAT24WC02 is addressed on the bus, all three address pins (A0, A1and A2) can be left floating or connected to VSS. A total of four devices can be addressed on a single bus when using CAT24WC04 device. Only A1 and A2 address pins are used with this device. The A0 address pin is a no connect pin and can be tied to VSS or left floating. If only one CAT24WC04 is being addressed on the bus, the address pins (A1 and A2) can be left floating or connected to VSS. Only two devices can be cascaded when using CAT24WC08. The only address pin used with this device is A2. The A0 and A1 address pins are no connect pins and can be tied to VSS or left floating. If only one CAT24WC08 is being addressed on the bus, the address pin (A2) can be left floating or connected to VSS. The CAT24WC16 is a stand alone device. In this case, all address pins (A0, A1and A2) are no connect pins and can be tied to VSS or left floating. WP: Write Protect If the WP pin is tied to VCC the entire memory array becomes Write Protected (READ only). When the WP pin is tied to VSS or left floating normal read/write operations are allowed to the device. stable whenever the clock line is high. Any changes in the data line while the clock line is high will be interpreted as a START or STOP condition. START Condition The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT24WC01/02/04/08/16 monitor the SDA and SCL lines and will not respond until this condition is met. STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. DEVICE ADDRESSING The bus Master begins a transmission by sending a START condition. The Master then sends the address of the particular slave device it is requesting. The four most significant bits of the 8-bit slave address are fixed as 1010 for the CAT24WC01/02/04/08/16 (see Fig. 5). The next three significant bits (A2, A1, A0) are the device address bits and define which device or which part of the device the Master is accessing. Up to eight CAT24WC01/ 02, four CAT24WC04, two CAT24WC08, and one CAT24WC16 may be individually addressed by the system. The last bit of the slave address specifies whether a Read or Write operation is to be performed. When this bit is set to 1, a Read operation is selected, and when set to 0, a Write operation is selected. After the Master sends a START condition and the slave address byte, the CAT24WC01/02/04/08/16 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave I2C Bus Protocol The following defines the features of the I2C bus protocol: (1) Data transfer may be initiated only when the bus is not busy. (2) During a data transfer, the data line must remain Figure 4. Acknowledge Timing SCL FROM MASTER 1 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACKNOWLEDGE 5020 FHD F06 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 5 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 Figure 5. Slave Address Bits CAT24WC01/02 1 0 1 0 A2 A1 A0 R/W CAT24WC04 1 0 1 0 A2 A1 a8 R/W CAT24WC08 1 0 1 0 A2 a9 a8 R/W CAT24WC16 1 0 1 0 a10 a9 a8 R/W * A0, A1 and A2 correspond to pin 1, pin 2 and pin 3 of the device. ** a8, a9 and a10 correspond to the address of the memory array address word. *** A0, A1 and A2 must compare to its corresponding hard wired input pins (pins 1, 2 and 3). address. The CAT24WC01/02/04/08/16 then performs a Read or Write operation depending on the state of the R/W bit. Acknowledge After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. The CAT24WC01/02/04/08/16 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8-bit byte. When the CAT24WC01/02/04/08/16 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT24WC01/02/04/08/16 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. WRITE OPERATIONS Byte Write In the Byte Write mode, the Master device sends the START condition and the slave address information (with the R/W bit set to zero) to the Slave device. After the Slave generates an acknowledge, the Master sends the byte address that is to be written into the address pointer of the CAT24WC01/02/04/08/16. After receiving another acknowledge from the Slave, the Master device transmits the data byte to be written into the addressed memory location. The CAT24WC01/02/04/08/16 acknowledge once more and the Master generates the STOP condition, at which time the device begins its internal programming cycle to nonvolatile memory. While this internal cycle is in progress, the device will not respond to any request from the Master device. Page Write The CAT24WC01/02/04/08/16 writes up to 16 bytes of data in a single write cycle, using the Page Write operation. The Page Write operation is initiated in the same manner as the Byte Write operation, however instead of terminating after the initial word is transmitted, Doc. No. 1022, Rev. N 6 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 the Master is allowed to send up to fifteen additional bytes. After each byte has been transmitted the CAT24WC01/02/04/08/16 will respond with an acknowledge, and internally increment the low order address bits by one. The high order bits remain unchanged. If the Master transmits more than sixteen bytes prior to sending the STOP condition, the address counter ‘wraps around ’ , and previously transmitted data will be overwritten. Once all sixteen bytes are received and the STOP condition has been sent by the Master, the internal programming cycle begins. At this point all received data is written to the CAT24WC01/02/04/08/16 in a single write cycle. Acknowledge Polling The disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host’s write operation, the CAT24WC01/02/04/08/16 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address for a write operation. If the CAT24WC01/02/04/ 08/16 is still busy with the write operation, no ACK will be returned. If the CAT24WC01/02/04/08/16 has completed the write operation, an ACK will be returned and the host can then proceed with the next read or write operation. WRITE PROTECTION The Write Protection feature allows the user to protect against inadvertent programming of the memory array. If the WP pin is tied to VCC, the entire memory array is protected and becomes read only. The CAT24WC01/ 02/04/08/16 will accept both slave and byte addresses, but the memory location accessed is protected from programming by the device’s failure to send an acknowledge after the first byte of data is received. READ OPERATIONS The READ operation for the CAT24WC01/02/04/08/16 is initiated in the same manner as the write operation with the one exception that the R/W bit is set to a one. Three different READ operations are possible: Immediate Address READ, Selective READ and Sequential READ. Immediate Address Read The CAT24WC01/02/04/08/16 ’ s address counter contains the address of the last byte accessed, incremented by one. In other words, if the last READ or WRITE access was to address N, the READ immediately following would access data from address N+1. If N=E (where E = 255 for 24WC02, 511 for 24WC04, 1023 for 24WC08, and 2047 for 24WC16), then the counter will 'wrap around' to address 0 and continue to clock out data. If N = E (where E = 127 for the CAT24WC01) the counter will not 'wrap around'. Figure 6. Byte Write Timing S T A R T S A C K A C K A C K S T O P P 5020 FHD F08 BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS * BYTE ADDRESS DATA Figure 7. Page Write Timing S T A R T S A C K S T O P P A C K A C K A C K A C K BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS * BYTE ADDRESS (n) DATA n DATA n+1 DATA n+P NOTE: IN THIS EXAMPLE n = XXXX 0000(B); X = 1 or 0 P=7 for CAT24WC01 and P=15 for CAT24WC02/04/08/16 * = Don't care for CAT24WC01 24WCXX F09 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 7 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 Selective Read Selective READ operations allow the Master device to select at random any memory location for a READ operation. The Master device first performs a ‘dummy’ write operation by sending the START condition, slave address and byte address of the location it wishes to read. After the CAT24WC01/02/04/08/16 acknowledge the word address, the Master device resends the START condition and the slave address, this time with the R/W bit set to one. The CAT24WC01/02/04/08/16 then responds with its acknowledge and sends the 8-bit byte requested. The master device does not send an acknowledge but will generate a STOP condition. operations. After the 24WC01/02/04/08/16 sends initial 8-bit byte requested, the Master will respond with an acknowledge which tells the device it requires more data. The CAT24WC01/02/04/08/16 will continue to output an 8-bit byte for each acknowledge sent by the Master. The operation is terminated when the Master fails to respond with an acknowledge, thus sending the STOP condition. The data being transmitted from the CAT24WC01/02/ 04/08/16 is outputted sequentially with data from address N followed by data from address N+1. The READ operation address counter increments all of the CAT24WC01/02/04/08/16 address bits so that the entire memory array can be read during one operation. If more than the E (where E = 255 for 24WC02, 511 for 24WC04, 1023 for 24WC08, and 2047 for 24WC16) bytes are read out, the counter will “wrap around” and continue to clock out data bytes. If N = E (where E = 127 for the CAT24WC01) the counter will not 'wrap around'. Sequential Read The Sequential READ operation can be initiated by either the immediate Address READ or Selective READ Figure 8. Immediate Address Read Timing S T A R T S A C K DATA N O A C K BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS S T O P P SCL 8 9 SDA 8TH BIT DATA OUT NO ACK STOP 5020 FHD F10 Doc. No. 1022, Rev. N 8 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 Figure 9. Selective Read Timing S T A R T S A C K S T A R T S A C K A C K DATA n N O A C K S T O P P BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS * BYTE ADDRESS (n) SLAVE ADDRESS 24WCXX F11 Figure 10. Sequential Read Timing BUS ACTIVITY: MASTER SDA LINE A C K A C K A C K A C K N O A C K SLAVE ADDRESS DATA n DATA n+1 DATA n+2 DATA n+x S T O P P 5020 FHD F12 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 9 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 8-LEAD 300 MIL WIDE PLASTIC DIP (P, L, GL) 0.245 (6.17) 0.295 (7.49) 0.355 (9.02) 0.400 (10.16) 0.120 (3.05) 0.150 (3.81) 0.180 (4.57) MAX 0.300 (7.62) 0.325 (8.26) 0.015 (0.38) 0.110 (2.79) 0.150 (3.81) 0.310 (7.87) 0.380 (9.65) 0.100 (2.54) BSC 0.045 (1.14) 0.060 (1.52) 0.014 (0.36) 0.022 (0.56) Notes: 1. Complies with JEDEC Publication 95 MS001 dimensions; however, some of the dimensions may be more stringent. 2. All linear dimensions are in inches and parenthetically in millimeters. 8-LEAD 150 MIL WIDE SOIC (J, W, GW) 0.1497 (3.80) 0.1574 (4.00) 0.2284 (5.80) 0.2440 (6.20) 0.1890 (4.80) 0.1968 (5.00) 0.0099 (0.25) X 45 0.0196 (0.50) 0.0532 (1.35) 0.0688 (1.75) 0 —8 0.0075 (0.19) 0.0098 (0.25) 0.050 (1.27) BSC 0.013 (0.33) 0.020 (0.51) 0.0040 (0.10) 0.0098 (0.25) 0.016 (0.40) 0.050 (1.27) Notes: 1. Complies with JEDEC publication 95 MS-012 dimensions; however, some dimensions may be more stringent. 2. All linear dimensions are in inches and parenthetically in millimeters. Doc. No. 1022, Rev. N 10 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 8 LEAD MSOP (R, Z, GZ) 0.0150 0.0110 0.38 0.28 0.1970 0.1890 5.00 4.80 S 0.0256 [0.65] BSC 0.1220 0.1142 3.10 2.90 0.0433 [1.10] MAX. 0.0374 0.0295 0.95 0.75 0.039 [0.10] MAX. S 0.0059 0.0020 0.15 0.05 S 0.0150 0.0110 0.38 0.28 WITH PLATING 0.0276 0.0157 0.70 0.40 0.1220 0.1142 3.10 2.90 0.0091 0.0051 0˚ - 6˚ WITH 0.23 0.13 PLATING 0.0050 [0.127] BASE METAL 0.0118 [0.30] REF. SECTION A - A Notes: (1) All dimensions are in mm Angles in degrees. 2 Does not include Mold Flash, Protrusion or Gate Burrs. Mold Flash, Protrusions or Gate Burrs shall not exceed 0.15 mm. per side. 3 Does not include Interlead Flash orProtrusion. Interlead Flash or Protrusion shall not exceed 0.25 mm per side. 4 Does not include Dambar Protrusion, allowable Dambar Protrusion shall be 0.08 mm. (5) This part is compliant with JEDEC Specification MO-187 Variations AA. (6) Lead span/stand off height/coplanarity are considered as special characteristics. (S) (7) Controlling dimensions in inches. [mm] © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 11 Doc. No. 1022, Rev. N CAT24WC01/02/04/08/16 8-LEAD TSSOP (U, Y, GY) Doc. No. 1022, Rev. N 12 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24WC01/02/04/08/16 ORDERING INFORMATION Prefix CAT Device # 24WC02 Suffix J I -1.8 TE13 REV-E Optional Company ID Product Number 24WC01: 1K 24WC02: 2K 24WC04: 4K 24WC08: 8K 24WC16: 16K Temperature Range Blank = Commercial (0°C to 70°C) I = Industrial (-40°C to 85°C) A = Automotive (-40°C to 105°C) E = Extended (-40°C to 125°C) Tape & Reel Package P: PDIP J: SOIC, JEDEC U: TSSOP** R: MSOP** L: PDIP (Lead-free, Halogen-free) W: SOIC (Lead-free, Halogen-free) Z: MSOP (Lead-free, Halogen-free)** Y: TSSOP (Lead-free, Halogen-free)** GL: PDIP (Lead-free, Halogen-free, NiPdAu lead plating) GW: SOIC, JEDEC (Lead-free, Halogen-free, NiPdAu lead plating) GZ: MSOP (Lead-free, Halogen-free, NiPdAu lead plating)** GY: TSSOP (Lead-free, Halogen-free, NiPdAu lead plating)** Operating Voltage Blank: 2.5V - 5.5V 1.8: 1.8V - 5.5V Die Revision 24WC01: C, E, F 24WC02: C, E, F 24WC04: F 24WC08: F 24WC16: D, F ** Available for CAT24WC01, CAT24WC02 and CAT24WC04 Notes: (1) The device used in the above example is a CAT24WC02JI-1.8TE13REV-E (SOIC, Industrial Temperature, 1.8 Volt to 5.5 Volt Operating Voltage, Tape & Reel, Die Revision E) © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 13 Doc. No. 1022, Rev. N REVISION HISTORY Date 2/3/2004 Rev. H Reason Added: CAT24WC01/02/16 not recommended for new designs. See CAT24FC01, CAT24FC02 and CAT24FC16 data sheets Added Die Revision to ordering information Update DC operating characteristics and notes Added Die Revision E to ordering information Edit Ordering Information Edit Features Edit Features Edit Pin Functions Edit Reliability Characteristics Edit D.C. Operating Characteristics Edit A.C. Characteristics Add Package Dimensions Edit Ordering Information 5/28/2004 7/28/2004 1/27/2005 2/28/2005 3/18/2005 08/12/05 I J K L M N Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ AE2 ™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.caalyst-semiconductor.com Publication #: Revison: Issue date: 1022 N 08/12/05