CAT40C00LITE13

CAT24C00 128-Bit Serial EEPROM FEATURES I 400 kHz I2C bus compatible* I 1.8 to 5.5 volt operation I Low power CMOS technology I Self-timed write cycle with auto-clear I 1,000,000 Program/erase cycles I 100 year data retention I 8-pin DIP, 8-pin SOIC, 8 pin TSSOP and SOT-23 I Industrial and Extended Temperature Ranges DESCRIPTION The CAT24C00 is a 128-bit Serial CMOS EEPROM internally organized as 16 words of 8 bits each. Catalyst’s advanced CMOS technology substantially reduces device power requirements. The device operates via the I2C bus serial interface and is available in 8-pin DIP, 8-pin SOIC, 8-pin TSSOP and 5-pin SOT-23. PIN CONFIGURATION DIP Package (P, L, GL) NC NC NC VSS 1 2 3 4 8 7 6 5 VCC NC SCL SDA SOIC Package (J, W, GW) NC NC NC VSS 1 2 3 4 SOT-23 (TP, TB, GTB) SCL VSS SDA 1 2 3 5 VCC PIN FUNCTIONS Pin Name SDA SCL NC is D 4 NC NC NC NC VSS o c 1 2 3 4 TSSOP Package (U, Y, GY) 8 7 6 5 i t n 8 7 6 5 VCC NC SCL SDA u n VCC VSS SDA BLOCK DIAGRAM EXTERNAL LOAD d e a P t r DOUT ACK SENSE AMPS SHIFT REGISTERS WORD ADDRESS BUFFERS COLUMN DECODERS VCC NC SCL SDA START/STOP LOGIC XDEC CONTROL LOGIC E2PROM Function DATA IN STORAGE Serial Data/Address HIGH VOLTAGE/ TIMING CONTROL SCL STATE COUNTERS Serial Clock No Connect 1.8 V to 5.5 V Power Supply Ground VCC VSS * Catalyst Semiconductor is licensed by Philips Corporation to carry the I2C Bus Protocol. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 1 Doc. No. 1027, Rev. O CAT24C00 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias ................. –55°C to +125°C Storage Temperature ....................... –65°C to +150°C Voltage on Any Pin with Respect to Ground(1) ............ –2.0 V to VCC + 2.0 V VCC with Respect to Ground ............. –2.0 V to +7.0 V Package Power Dissipation Capability (TA = 25°C) .................................. 1.0 W Lead Soldering Temperature (10 seconds) ...... 300°C Output Short Circuit Current(2) ....................... 100 mA RELIABILITY CHARACTERISTICS Symbol NEND(3) TDR(3) VZAP (3) *COMMENT Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Parameter Endurance Data Retention ESD Susceptibility Latch-up Min. 1,000,000 100 2000 100 Typ. Max. ILTH(3)(4) D.C. OPERATING CHARACTERISTICS VCC = 1.8 V to 5.5 V, unless otherwise specified. Symbol ICC ISB (5) Parameter Power Supply Current Standby Current (VCC = 5.0 V) Input Leakage Current Output Leakage Current Input Low Voltage ILI ILO VIL VIH VOL1 VOL2 CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5 V Symbol CI/O(3) CIN(3) Parameter Test Conditions VI/O = 0 V VIN = 0 V Min Typ Max 8 6 Units pF pF Input/Output Capacitance (SDA) Input Capacitance (SCL) Note: (1) The minimum DC input voltage is – 0.5 V. During transitions, inputs may undershoot to – 2.0 V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC + 0.5 V, which may overshoot to VCC + 2.0 V for periods of less than 20 ns. (2) Output shorted for no more than one second. No more than one output shorted at a time. (3) These parameter are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100 and JEDEC test methods. (4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from – 1 V to VCC + 1 V. (5) Maximum standby current (ISB) = 10µA for the Extended Automotive temperature range. is D Input High Voltage Output Low Voltage (VCC = 3.0 V) Output Low Voltage (VCC = 1.8 V) o c i t n Test Conditions fSCL = 400 kHz VIN = GND or VCC VIN = GND to VCC u n d e Min –1 a P Max 2 1 10 10 VCC x 0.3 VCC + 0.5 0.4 0.5 Units Cycles/Byte Years Volts mA t r mA µA µA µA V V V V Typ Units VOUT = GND to VCC VCC x 0.7 IOL = 3 mA IOL = 1.5 mA Doc. No. 1027, Rev. O 2 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24C00 A.C. CHARACTERISTICS VCC = 1.8 V to 5.5 V, unless otherwise specified. Read & Write Cycle Limits Symbol Parameter 1.8 V - 6.0 V Min FSCL TI(1) tAA tBUF(1) tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR(1) tF (1) 2.5 V - 6.0 V Min Max 400 100 Units Max 100 100 3.5 Clock Frequency Noise Suppression Time Constant at SCL, SDA Inputs SCL Low to SDA Data Out and ACK Out Time the Bus Must be Free Before a New Transmission Can Start Start Condition Hold Time Clock Low Period Clock High Period Start Condition Setup Time (for a Repeated Start Condition) Data In Hold Time Data In Setup Time 4.7 4 4.7 4 1.2 SDA and SCL Rise Time SDA and SCL Fall Time tSU:STO tDH Stop Condition Setup Time Data Out Hold Time Power-Up Timing(1)(2) Symbol tPUR tPUW Write Cycle Limits Symbol tWR The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write cycle, the bus is D Parameter Power-up to Read Operation Power-up to Write Operation o c i t n u n 0 50 4 100 4.7 d e 1.2 0.6 0.6 0 50 1 300 0.6 100 Min Typ 0.6 a P 1 0.3 300 Max 1 1 t r kHz ns µs µs µs µs µs µs ns ns µs ns µs ns Units ms ms Parameter Write Cycle Time Min Typ Max 5 Units ms interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address. Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated. © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 3 Doc. No. 1027, Rev. O CAT24C00 FUNCTIONAL DESCRIPTION The CAT24C00 supports the I2C Bus data transmission protocol. This Inter-Integrated Circuit Bus protocol defines any device that sends data to the bus to be a transmitter and any device receiving data to be a receiver. Data transfer is controlled by the Master device which generates the serial clock and all START and STOP conditions for bus access. The CAT24C00 operates as a Slave device. Both the Master and Slave devices can operate as either transmitter or receiver, but the Master device controls which mode is activated. SDA: Serial Data/Address The CAT24C00 bidirectional serial data/address pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wire-ORed with other open drain or open collector outputs. I2C BUS PROTOCOL The following defines the features of the I2C bus protocol: (1) Data transfer may be initiated only when the bus is not busy. PIN DESCRIPTIONS SCL: Serial Clock The CAT24C00 serial clock input pin is used to clock all data transfers into or out of the device. This is an input pin. Figure 1. Bus Timing tF tLOW SCL tSU:STA tHD:STA tHD:DAT tHIGH tLOW (2) During a data transfer, the data line must remain stable whenever the clock line is high. Any changes in the data line while the clock line is high will be interpreted as a START or STOP condition. tR SDA IN tAA SDA OUT Figure 2. Write Cycle Timing SCL SDA Figure 3. Start/Stop Timing D is SDA SCL 8TH BIT BYTE n o c i t n u n tSU:DAT tDH tWR d e a P t r tSU:STO tBUF 5020 FHD F03 ACK STOP CONDITION START CONDITION ADDRESS 5020 FHD F04 5020 FHD F05 START BIT Doc. No. 1027, Rev. O STOP BIT 4 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24C00 START Condition The START Condition precedes all commands to the device, and is defined as a HIGH to LOW transition of SDA when SCL is HIGH. The CAT24C00 monitors the SDA and SCL lines and will not respond until this condition is met. STOP Condition A LOW to HIGH transition of SDA when SCL is HIGH determines the STOP condition. All operations must end with a STOP condition. The CAT24C00 responds with an acknowledge after receiving a START condition and its slave address. If the device has been selected along with a write operation, it responds with an acknowledge after receiving each 8bit byte. When the CAT24C00 is in a READ mode it transmits 8 bits of data, releases the SDA line, and monitors the line for an acknowledge. Once it receives this acknowledge, the CAT24C00 will continue to transmit data. If no acknowledge is sent by the Master, the device terminates data transmission and waits for a STOP condition. DEVICE ADDRESSING The bus Master begins a transmission by sending a START condition. The Master then sends the address of the particular slave device it is requesting. The four most significant bits of the 8-bit slave address are fixed as 1010 for the CAT24C00 (see Fig. 5). The next three significant bits are "don't care" bits. The last bit of the slave address specifies whether a Read or Write operation is to be performed. When this bit is set to 1, a Read operation is selected, and when set to 0, a Write operation is selected. After the Master sends a START condition and the slave address byte, the CAT24C00 monitors the bus and responds with an acknowledge (on the SDA line) when its address matches the transmitted slave address. The CAT24C00 then performs a Read or Write operation depending on the state of the R/W bit. Acknowledge WRITE OPERATION Byte Write After a successful data transfer, each receiving device is required to generate an acknowledge. The Acknowledging device pulls down the SDA line during the ninth clock cycle, signaling that it received the 8 bits of data. Figure 4. Acknowledge Timing is D o c START i t n 1 u n In the Write mode, the Master device sends the START condition and the slave address information (with the R/ W bit set to zero) to the Slave device. After the Slave generates an acknowledge, the Master sends the byte address that is to be written into the address pointer of the CAT24C00. After receiving another acknowledge from the Slave, the Master device transmits the data byte to be written into the addressed memory location. The CAT24C00 acknowledges once more and the Master generates the STOP condition, at which time the device begins its internal programming cycle to nonvolatile memory. While this internal cycle is in progress, the device will not respond to any request from the Master device. d e a P t r After a write command, the internal address counter will continue to point to the same address location that was just written. If a stop bit is transmitted to the device at any point in the write sequence before the entire sequence is complete, then the command will abort and no data will be written. If more than eight SCL FROM MASTER 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER ACKNOWLEDGE 5020 FHD F06 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 5 Doc. No. 1027, Rev. O CAT24C00 Figure 5. Slave Address Bits CAT24C00 1 0 1 0 X X X R/W bits are transmitted before the stop bit is sent, then the device will clear the previously loaded byte and begin loading the data buffer again. If more than one data byte is transmitted to the device and a stop bit is sent before a full eight bits of data have been transmitted, then the write command will abort and no data will be written. Acknowledge Polling Selective Read The disabling of the inputs can be used to take advantage of the typical write cycle time. Once the stop condition is issued to indicate the end of the host’s write operation, the CAT24C00 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the slave address for a write operation. If the CAT24C00 is still busy with the write operation, no ACK will be returned. If the CAT24C00 has completed the write operation, an ACK will be returned and the host can then proceed with the next read or write operation. READ OPERATIONS The READ operation for the CAT24C00 is initiated in the same manner as the write operation with the one exception that the R/W bit is set to a one. Three different READ operations are possible: Immediate Address READ, Selective READ and Sequential READ. Immediate Address Read is D o c i t n u n Selective READ operations allow the Master device to select at random any memory location for a READ operation. The Master device first performs a ‘dummy’ write operation by sending the START condition, slave address and byte address of the location it wishes to read. After the CAT24C00 acknowledges the word address, the Master device resends the START condition and the slave address, this time with the R/W bit is set to one. The CAT24C00 then responds with its acknowledge and sends the 8-bit byte requested. To end the Read Operation the master device does not send an acknowledge but will generate a STOP condition. d e a P t r Sequential Read The Sequential READ operation can be initiated by either the immediate Address READ or Selective READ operations. After the CAT24C00 sends initial 8-bit byte requested, the Master will respond with an acknowledge which tells the device it requires more data. The CAT24C00 will continue to output an 8-bit byte for each acknowledge sent by the Master. The operation is terminated when the Master fails to respond with an acknowledge, thus sending the STOP condition. The data being transmitted from the CAT24C00 is outputted sequentially with data from address N followed by data from address N+1. The READ operation address counter increments all of the CAT24C00 address bits so that the entire memory array can be read during one operation. If more than 16 bytes are read out, the counter will “wrap around” and continue to clock out data bytes. The device’s address counter contains the address of the last byte accessed, incremented by one. In other words, if the last READ access was to address N, the READ immediately following would access data from address N+1. If N=15, then the counter will 'wrap around' to address 0 and continue to clock out data. Doc. No. 1027, Rev. O 6 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24C00 Figure 6. Byte Write Timing S T A R T S A C K A C K A C K BUS ACTIVITY: MASTER SDA LINE SLAVE ADDRESS BYTE ADDRESS DATA S T O P P Figure 7. Immediate Address Read Timing S T BUS ACTIVITY: A MASTER R T SDA LINE S A C K S T O P SLAVE ADDRESS DATA SCL SDA Figure 8. Selective Read Timing BUS ACTIVITY: MASTER Figure 9. Sequential Read Timing BUS ACTIVITY: MASTER SDA LINE A C K A C K A C K A C K N O A C K SLAVE ADDRESS S T O P P D is SDA LINE o c S T A R T S SLAVE ADDRESS i t n 8 8TH BIT DATA OUT u n 9 NO ACK d e P N O A C K a P STOP t r BYTE ADDRESS (n) S T A R T S SLAVE ADDRESS S T O P P A C K DATA n N O A C K A C K A C K DATA n DATA n+1 DATA n+2 DATA n+x © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 7 Doc. No. 1027, Rev. O CAT24C00 ORDERING INFORMATION Prefix CAT Device # 24C00 Suffix J I X TE13 Rev B(2) Optional Company ID Product Number 24C00: 128 Bit Temperature Range I = Industrial (-40°C to 85°C) E = Extended (-40°C to 125°C) Tape & Reel Package P: PDIP J : SOIC (JEDEC) U: TSSOP TP: SOT23 L : PDIP (Lead free, Halogen free) TB: SOT23 (Lead free, Halogen free) W: SOIC (Lead free, Halogen free) Y: TSSOP (Lead free, Halogen free) GL: PDIP (Lead-free, Halogen-free, NiPdAu lead plating) GTB: SOT23 (Lead-free, Halogen-free, NiPdAu lead plating) GW: SOIC (Lead-free, Halogen-free, NiPdAu lead plating) GY: TSSOP (Lead-free, Halogen-free, NiPdAu lead plating) Operating Voltage Blank: 1.8 V - 5.5 V Notes: (1) The device used in the above example is a CAT24C00JI-TE13 (SOIC, Industrial Temperature, 1.8 Volt to 5.5 Volt Operating Voltage, Tape & Reel) (2) Product die revision letter is marked on top of the package as a suffix to the production date code (e.g. AYWWB). For additional information, please contact your Catalyst sales office. is D Doc. No. 1027, Rev. O o c i t n u n d e a P Die Revision t r 8 © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT24C00 REVISION HISTORY Date 9/24/2003 10/30/2003 12/9/2003 12/23/2003 12/29/2003 Rev. H I J K L Reason Eliminated commercial temperature range class Updated marking Eliminated automotive temperature reange Changed Industrial temp range designation from "Blank" to "I" Eliminatd Commercial and Automotive temp ranges from Features on front page of data sheet Moved DC Operating Characteristics typ numbers for VOL1 and VOL2 to max column Changed 1.8V to 1.8V - 6.0V for AC Characteristics Changed 4.5V - 5.5V to 2.5V - 6.0V for AC Characteristics 7/7/2004 7/27/2004 07/12/2005 M N O Added Die Revision to Ordering Information Updated DC Operating Characteristics chart and notes Upate Rekiability Characteristics table Update Ordering Information is D o c i t n u n d e a P t r © 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 9 Doc. No. 1027, Rev. O Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP ™ AE2 ™ MiniPot™ Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company’s corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. is D o c i t n u n d e a P t r Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.caalyst-semiconductor.com Publication #: Revison: Issue date: 1027 O 7/12/05