AXLH472P025EL

Type AXLH -40 ºC to +150 ºC High Temperature Axial Leaded Aluminum Electrolytic Capacitors High Performance Axial Leaded Aluminum Electrolyic Capacitors Highlights 470 to 4700 µF Capacitance Tolerance (100 Hz/+20 ºC) -10/+30% Rated Voltage 25, 40, 63 Vdc Operating Temperature -40 ºC to +150 ºC Leakage Current (at 20°C) I = 0.003 CV +4.0 µA; after 5 minutes at rated voltage I = leakage current in µAmps C = rated capacitance in µF V = rated DC Working voltage in Volts Standard al te ed Frequency (Hz) 100 300 Ripple Current Correction Factor 0.35 0.57 su gg es t Ripple Current vs. Frequency Correction Factors Shelf Life rn Capacitance Range (100 Hz/+20 ºC) Film Specifications at iv e - 150 °C Operating Temperature - Up to 28 Amps RMS Continuous Ripple Current - Capacitance Range: 470 µF to 4700 µF - High Vibration Resistance - Very Long Shelf Life - Low Leakage Current N H R Type AXLH capacitors are a new generation of high performance aluminum electrolytic capacitors rated up to 2000 hours at 150 ºC. They are designed for applications that place high demands on a capacitor. The capacitor’s outstanding features include low ESR, low leakage current, a long shelf life and a high ripple current capability. 1000 5000 0.8 1 100 kHz 1.04 (+105 ºC/0 Vdc): 5000 hours (+40 ºC/0 Vdc): 10 years IEC 60384-4 long life grade 40/125/56 RoHS Compliant 222 P 025 E D Capacitance Capacitance Tolerance Voltage Code Case Dia.Code Length Code 222 = 2200 µF P = -10/+30% 025 = 25 Vdc E = 20 mm D = 27 mm LE T AXLH E Part Numbering System Case 040 = 40 Vdc H = 35 mm 063 = 63 Vdc L = 43 mm O BS O Type CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800 Type AXLH -40 ºC to +150 ºC High Temperature Axial Leaded Aluminum Electrolytic Capacitors Load Life Test ∆C Capacitance will be within ±15% of the initial value Clamp the case to the test fixture. Frequency range is 10 - 2000 Hz. Amplitude of 1.5mm or 20 g acceleration. Duration of test is 22 hours in each of three directions. After the test, measure the capacitance at +20°C. ∆C Capacitance change from the initial measurement must not exceed 5%. rn at iv Test Film Vibration Test No electrolyte leakage or other visible damage. The markings will be legible. e Appearance H ESR will be less than 2 times the initial value The leakage current will be within the specified value N ESR DCL R Test Mount the capacitor on a heat sink with a low thermal resistance path. Apply the maximum rated voltage for 2000 hrs at +150°C with the +150°C maximum ripple current applied to the capacitor. After the test, measure the capacitance, ESR, and DCL at +20°C. Test Subject the capacitor to 1000 surge voltage cycles at +150°C. For each cycle, apply 1.15 times the rated voltage for 30 seconds followed by no voltage for 5 min. and 30 seconds. The time constant for charging is 0.1 seconds. After one to two hours, measure the capacitance and esr. ∆C Capacitance change from the initial measurement must not exceed 15%. ESR The ESR will be < 2x initial value. ed Surge Voltage Test al te Appearance No electrolyte leakage or other visible damage. su gg es t Appearance No electrolyte leakage or other visible damage. Storage at Low Temperature Test Test Subject the capacitor to 72 hours at -55°C. After 16 hours at room temperature, measure the capacitance and DCL. ∆C Capacitance change from the initial measurement must not exceed 10%. DCL Leakage current will meet the initial specification. Appearance No electrolyte leakage or other visible damage. The markings are to be legible. Test Subject the capacitor to 1 million charge/discharge cycles at +20°C. For each cycle, apply the rated voltage for 0.5 seconds using a 0.1 second charge/discharge time constant. After the test, the following will apply; ∆C Capacitance will be within ±10% of the initial value. Appearance No electrolyte leakage or other visible damage. O BS O LE T E Charge and Discharge Test CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800 Type AXLH -40 ºC to +150 ºC High Temperature Axial Leaded Aluminum Electrolytic Capacitors Ratings (µF) (%) 2200 -10/+30 Cornell Dubilier Part Number 25 AXLH222P025ED Case Size DxL Rated Maximum Max. ESR Max. ESR Ripple Current Ripple Current 100 Hz/+20°C 100 kHz/+20°C ≥ 5kHz/+125°C ≥ 5kHz/+125°C (mm) (mΩ) (mΩ) (A) 20 x 27 50 25 7.1 (A) 9.1 3300 -10/+30 25 AXLH332P025EH 20 x 35 34 17 8.9 4700 -10/+30 25 AXLH472P025EL 20 x 43 25 13 10.3 1500 -10/+30 40 AXLH152P040ED 20 x 27 57 22 7.3 9.3 2200 -10/+30 40 AXLH222P040EH 20 x 35 41 17 8.9 11.2 2700 -10/+30 40 AXLH272P040EL 20 x 43 32 13 63 AXLH471P063ED 20 x 27 125 32 63 AXLH681P063EH 20 x 35 87 23 900 -10/+30 63 AXLH901P063EL 20 x 43 67 18 N e at iv -10/+30 -10/+30 10.1 12.8 5.5 7.0 6.9 8.7 8.1 10.2 BS O LE T E su gg es t Outline Drawings & Dimensions Table ed al te rn 470 680 11.3 13.1 Dimensions in mm Size Code Approximate Weight (grams) D L d LL ± 0.5 ±1 ± 0.03 ±2 ED 20 26.5 1 40 13 EH 20 34.5 1 40 20 EL 20 42.5 1 40 24 Note: Bend leads at least 3.5 mm from the case. CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800 Film O VDC R Capacitance Tolerance H Rated Capacitance 100Hz/+20°C Type AXLH -40 ºC to +150 ºC High Temperature Axial Leaded Aluminum Electrolytic Capacitors R Cornell Dubilier Part Number AXLH222P025ED 10.6 22.2 14 6.3 AXLH332P025EH 7.8 25.8 16.3 7.3 AXLH472P025EL 6.4 28.5 18 AXLH152P040ED 10 22.8 14.4 AXLH222P040EH 7.9 25.7 16.2 6.7 27.9 17.6 17.5 17.3 10.9 AXLH681P063EH 13 20 AXLH901P063EL 10.6 22.2 N 8.1 rn AXLH272P040EL AXLH471P063ED ≥ 5 kHz/+150°C (A) e ≥ 5 kHz/+140°C (A) at iv ≥ 5 kHz/+125°C (A) H Maximum Ripple Current * Max. ESR 5-100 kHz 125-150°C (mΩ) 6.5 7.3 7.9 4.9 12.7 5.7 14 6.3 al te Film Heat-Sinked Ratings Marking Description -- CDM ++ Logo, Polarity Marks AXLH222P025ED CDE Part Number 2200 uF 25VDC Capacitance, Rated Voltage (VDC) 160603 Date Code (Year, Week), Batch Number O BS O LE T E Capacitor Markings su gg es t ed * When the capacitor is mounted to a heat-sink using low thermal resistance path. CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800 rn al te ed su gg es t E LE T O BS O Film at iv e N H R Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.