CD9013G

Continental Device India Limited An ISO/TS16949 and ISO 9001 Certified Company NPN SILICON PLANAR TRANSISTOR CD9013 TO-92 Plastic Package BC E General Purpose Audio Amplifier Applications ABSOLUTE MAXIMUM RATINGS (Ta=25ºC Unless Otherwise Specified) VALUE DESCRIPTION SYMBOL VCEO 30 Collector Emitter Voltage VCBO 40 Collector Base Voltage VEBO 5 Emitter Base Voltage Collector Current Continuous Collector Power Dissipation Operating And Storage Junction Temperature Range IC PC Tj, Tstg 500 625 -55 to +150 UNITS V V V mA mW ºC ELECTRICAL CHARACTERISTICS (Ta=25ºC Unless Otherwise Specified) TEST CONDITION DESCRIPTION SYMBOL IC=1mA, IB=0 VCEO Collector Emitter Voltage VCBO IC=100µA, IE=0 Collector Base Voltage Emitter Base Voltage Collector Cut off Current Emitter Cut off Current DC Current Gain Collector Emitter Saturation Voltage Base Emitter Saturation Voltage DYNAMIC CHARACTERISTICS Output Capacitance Transition Frequency Noise Figure *hFE CLASSIFICATION VEBO ICBO IEBO *hFE hFE VCE(sat) VBE(sat) IE=100µA, IC=0 VCB=25V, IE = 0 VBE=3V, IC = 0 VCE=1V, IC=50mA VCE=1V, IC=500mA IC=150mA, IB=15mA IC=500mA, IB=50mA IC=150mA, IB=15mA IC=500mA, IB=50mA MIN 30 40 5 MAX UNITS V V V 100 100 64 40 0.2 0.6 1.0 1.2 10 6.0 J: 278 - 465 465 nA nA V V V V pF MHz dB VCB=10V, f=1MHz Cob IC=50mA, VCE=10V, f=100MHz fT 200 VCE =10V,IC=1mA, f=1KHz NF D/E/F:64 - 135 G/H/I: 118 - 305 CD9013Rev_1170603D Continental Device India Limited Data Sheet Page 1 of 4 CD9013 TO-92 Plastic Package TO-92 Plastic Package B Dimension With 'L' Uncontrolled L DIM A B C D E F G H K L MIN. 4.32 4.45 3.18 0.41 0.35 MAX. 5.33 5.20 4.19 0.55 0.50 A Beyond 'L' 2 3 D G F F AA K 1 D E SEC AA 5 DEG 1.14 1.40 1.20 1.40 12.70 — 1.982 2.082 1.03 1.20 M All dimensions are in mm M Solderability Ensured 321 Mold Parting Line H C PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER 321 The TO-92 Package, Tape and Ammo Pack Drawings are correct as on the date of issue/revision of this Data Sheet. The currently valid dimensions and information, may please be confirmed from the TO-92 Drawing in the Packages and Packing Section of the Product Catalogue. Packing Details PACKAGE Details TO-92 Bulk TO-92 T&A 1K/ polybag 2K/ ammo box STANDARD PACK Net Weight/ Qty 200 gm/ pcs 1K 645 gm/ pcs 2K Size 3" x 7.5" x 7.5" 12.5" x 8" x 1.8" INNER CARTON BOX Qty 5K 2K Size 17" x 15" x 13.5" 17" x 15" x 13.5" OUTER CARTON BOX Qty 80K 32K Gr Wt 23 kgs 12.5 kgs CD9013Rev_1170603D Continental Device India Limited Data Sheet Page 2 of 4 CD9013 TO-92 Plastic Package TO-92 Tape and Ammo Pack Tape Mechanical Data T h h A H3 H1 Ho L H2 C1 C2 W2 Wo A1 P (p) h1 h1 Ammo Pack Style Adhesive Tape on Top Side Flat side Label D FEE Carrier Strip 186 (7.3") W1 W F1 t1 t P2 Po F F2 Do 332 ") (1 3 (1. 43 7") Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions are in mm ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT * 1 FEED HOLE PITCH * 2 FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS SPECIFICATION SYMBOL A1 A T P Po P2 F h h1 W Wo W1 W2 Ho H1 L Do t F1, F2 H2 H3 | C1 - C2 | (p) 0.45 MIN. NOM. MAX. 4.0 4.8 3.9 12.7 12.7 6.35 5.08 0 0 18 6 9 0.5 16 23.25 11.0 4 1.2 2.54 1.45 3.0 0.22 + 0.4 - 0.1 ± 0.2 REMARKS 1.0 1.3 ± 0.5 ± 0.2 + 0.7 - 0.5 ± 0.2 ± 0.5 4.8 5.2 4.2 ± 1.0 ± 0.3 ± 0.4 + 0.6 - 0.2 TOL . NOTES 1. Maximum alignment deviation between leads will not to be greater than 0.2mm. 2. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. 3. Holddown tape will not exceed beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 4. There will be no more than three (3) consecutive missing components in a tape. 5. A tape trailer, having at least three feed holes are provided after the last component in a tape. 6. Splices should not interfere with the sprocket feed holes. * 3 COMPONENT ALIGNMENT SIDE VIEW * 4 COMPONENT ALIGNMENT FRONT VIEW TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER * 5 TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCE STAND OFF CLINCH HEIGHT LEAD PARALLELISM PULL - OUT FORCE 6N * 1 Cumulative pitch error 1.0 mm/20 pitch * 2 To be measured at bottom of clinch * 3 At top of body * 4 At top of body * 5 t1 0.3 – 0.6 mm CD9013Rev_1170603D Continental Device India Limited Data Sheet Page 3 of 4 Notes CD9013 TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the CDIL Web Site/CD are believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119 email@cdil.com www.cdilsemi.com CD9013Rev_1170603D Continental Device India Limited Data Sheet Page 4 of 4