PS2715-1-F3

PHOTOCOUPLER PS2715-1 HIGH CTR, AC INPUT 4-PIN SOP PHOTOCOUPLER −NEPOC Series− DESCRIPTION The PS2715-1 is an optically coupled isolator containing GaAs light emitting diodes and an NPN silicon phototransistor in a plastic SOP for high density applications. The package is an SOP (Small Outline Package) type for high density mounting applications. FEATURES • AC input response • High current transfer ratio (CTR = 200% TYP. @ IF = ±1 mA) • High isolation voltage (BV = 3 750 Vr.m.s.) • Small and thin package (4-pin SOP) • Ordering number of tape product: PS2715-1-F3, F4 • Pb-Free product • Safety standards • UL approved: File No. E72422 • DIN EN60747-5-2 (VDE0884 Part2) approved (Option) 1 2 4 PIN CONNECTION (Top View) 3 1. Anode, Cathode 2. Cathode, Anode 3. Emitter 4. Collector APPLICATIONS • Programmable logic controllers • Modem/FAX Document No. PN10247EJ02V0DS (2nd edition) Date Published April 2005 CP(K) The mark shows major revised points. PS2715-1 PACKAGE DIMENSIONS (UNIT: mm) 4±0.5 7.0±0.3 4.4 2.1±0.2 0.15 +0.10 –0.05 0.1±0.1 2.54 0.4 +0.10 –0.05 0.5±0.3 0.25 M MARKING EXAMPLE No. 1 pin Mark 2715 N003 Trade Mark Type Number Assembly Lot *1 N 0 03 Week Assembled Year Assembled (Last 1 Digit) CTR Rank Code *1 Bar : Pb-Free Remark "PS" and "-1" are omitted from original type number. 2 Data Sheet PN10247EJ02V0DS PS2715-1 ORDERING INFORMATION Part Number PS2715-1 PS2715-1-F3 PS2715-1-F4 PS2715-1-V PS2715-1-V-F3 PS2715-1-V-F4 PS2715-1 PS2715-1-F3 PS2715-1-F4 PS2715-1-V PS2715-1-V-F3 PS2715-1-V-F4 Order Number PS2715-1 PS2715-1-F3 PS2715-1-F4 PS2715-1-V PS2715-1-V-F3 PS2715-1-V-F4 PS2715-1-A PS2715-1-F3-A PS2715-1-F4-A PS2715-1-V-A PS2715-1-V-F3-A PS2715-1-V-F4-A Magazine case 100 pcs Embossed Tape 3 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) Pb-Free Magazine case 100 pcs Embossed Tape 3 500 pcs/reel Magazine case 100 pcs Embossed Tape 3 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) Standard products (UL approved) Solder Plating Specification Solder contains lead Packing Style Magazine case 100 pcs Embossed Tape 3 500 pcs/reel Safety Standard Approval Standard products (UL approved) Application Part *1 Number PS2715-1 *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (Unless otherw ise specified, TA = 25°C) Parameter Diode Forward Current (DC) Power Dissipation Derating Power Dissipation Peak Forward Current Transistor *1 Symbol IF Ratings ±50 0.8 80 ±0.5 40 5 40 1.5 150 3 750 –55 to +100 –55 to +150 Unit mA mW/°C mW A V V mA mW/°C mW Vr.m.s. °C °C ∆PD/°C PD IFP VCEO VECO IC Collector to Emitter Voltage Emitter to Collector Voltage Collector Current Power Dissipation Derating Power Dissipation ∆PC/°C PC BV TA Tstg Isolation Voltage *2 Operating Ambient Temperature Storage Temperature *1 PW = 100 µs, Duty Cycle = 1% *2 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. Pins 1-2 shorted together, 3-4 shorted together. Data Sheet PN10247EJ02V0DS 3 PS2715-1 ELECTRICAL CHARACTERISTICS (TA = 25°C) Parameter Diode Forward Voltage Terminal Capacitance Transistor Collector to Emitter Dark Current Coupled Current Transfer Ratio (IC/IF) Collector Saturation Voltage Isolation Resistance Isolation Capacitance Rise Time Fall Time *1 Symbol VF Ct ICEO IF = ±5 mA Conditions MIN. TYP. 1.15 60 MAX. 1.4 Unit V pF V = 0 V, f = 1 MHz IF = 0 mA, VCE = 40 V IF = ±1 mA, VCE = 5 V IF = ±1 mA, IC = 0.2 mA VI-O = 1 kVDC V = 0 V, f = 1 MHz VCC = 5 V, IC = 2 mA, RL = 100 Ω 10 11 100 nA CTR 100 200 400 % VCE (sat) RI-O CI-O tr tf 0.3 V Ω 0.4 4 5 pF µs *1 *1 Test circuit for switching time Pulse Input PW = 100 µs Duty cycle = 1/10 IF VCC In monitor 50 Ω RL = 100 Ω VOUT 4 Data Sheet PN10247EJ02V0DS PS2715-1 TYPICAL CHARACTERISTICS (Unless otherw ise specified, TA = 25°C) DIODE POWER DISSIPATION vs. AMBIENT TEMPERATURE Transistor Power Dissipation PC (mW) 100 200 TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Diode Power Dissipation PD (mW) 80 150 60 100 40 20 50 0 25 50 75 100 0 25 50 75 100 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) FORWARD CURRENT vs. FORWARD VOLTAGE 100 COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE Collector to Emitter Dark Current ICEO (nA) 10 000 Forward Current IF (mA) 10 1 000 VCE = 40 V 20 V 10 V TA = +100˚C +60˚C +25˚C 1 0˚C –25˚C –50˚C 100 0.1 10 0.01 0.0 0.5 1.0 1.5 2.0 1 –25 0 25 50 75 100 Forward Voltage VF (V) Ambient Temperature TA (˚C) COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 25 IF = 10 mA COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE 100 10 mA 5 mA 2 mA 10 1 mA 1 IF = 0.5mA Collector Current IC (mA) 5 mA 15 10 2 mA 5 1 mA 0.5 mA 0 2 4 6 8 10 Collector Current IC (mA) 20 0.1 0.0 0.2 0.4 0.6 0.8 1.0 Collector to Emitter Voltage VCE (V) Collector Saturation Voltage VCE(sat) (V) Remark The graphs indicate nominal characteristics. Data Sheet PN10247EJ02V0DS 5 PS2715-1 NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE Normalized Current Transfer Ratio CTR 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 –50 –25 0 25 Current Transfer Ratio CTR (%) CURRENT TRANSFER RATIO vs. FORWARD CURRENT 500 VCE = 5 V, n=3 400 300 200 Normalized to 1.0 at TA = 25˚C, IF = 1 mA, VCE = 5 V 50 75 100 100 0 0.01 0.1 1 10 100 Ambient Temperature TA (˚C) Forward Current IF (mA) SWITCHING TIME vs. LOAD RESISTANCE 100 IC = 2 mA, VCC = 5 V, CTR = 200% Switching Time t (µ s) 10 tf tr td 1 ts 0.1 10 0.1 100 1 000 SWITCHING TIME vs. LOAD RESISTANCE IF = 1 mA, VCC = 5 V, CTR = 200% Switching Time t (µs) 100 tf ts tr td 10 1 100 1k 10 k 1k 10 k 100 k Load Resistance RL (kΩ) Load Resistance RL (kΩ) FREQUENCY RESPONSE 1.2 LONG TERM CTR DEGRADATION IF = 1 mA 0 –5 –10 –15 –20 –25 0.1 300 Ω CTR (Relative Value) Normalized Gain Gv 1.0 0.8 TA = 25˚C 0.6 0.4 0.2 0 10 TA = 60˚C RL = 1 kΩ 100 Ω 1 10 100 1 000 102 103 104 105 106 Frequency f (kHz) Time (Hr) Remark The graphs indicate nominal characteristics. 6 Data Sheet PN10247EJ02V0DS PS2715-1 TAPING SPECIFICATIONS (in millimeters) Outline and Dimensions (Tape) 2.0±0.05 4.0±0.1 1.75±0.1 1.5+0.1 –0 2.9 MAX. 5.5±0.05 12.0±0.2 1.55±0.1 7.4±0.1 4.6±0.1 8.0±0.1 2.4±0.1 0.3 Tape Direction PS2715-1-F3 PS2715-1-F4 Outline and Dimensions (Reel) 2.0±0.5 φ 330±2.0 2.0±0.5 φ13.0±0.2 R 1.0 φ 21.0±0.8 φ 13.0±0.2 φ 100±1.0 13.5±1.0 17.5±1.0 Packing: 3 500 pcs/reel 11.9 to 15.4 Outer edge of flange Data Sheet PN10247EJ02V0DS 7 PS2715-1 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature • Time of peak reflow temperature • Time of temperature higher than 220°C • Time to preheat temperature from 120 to 180°C • Number of reflows • Flux 260°C or below (package surface temperature) 10 seconds or less 60 seconds or less 120±30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 260˚C MAX. 220˚C to 60 s 180˚C 120˚C 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature • Time • Preheating conditions • Number of times • Flux 260°C or below (molten solder temperature) 10 seconds or less 120°C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron • Peak temperature (lead part temperature) • Time (each pins) • Flux 350°C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100°C. 8 Data Sheet PN10247EJ02V0DS PS2715-1 (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Data Sheet PN10247EJ02V0DS 9 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.