PS2761-1-F4-A

PHOTOCOUPLER PS2761-1 HIGH ISOLATION VOLTAGE 4-PIN SOP PHOTOCOUPLER −NEPOC Series− DESCRIPTION The PS2761-1 is an optically coupled isolator containing a GaAs light emitting diode and an NPN silicon phototransistor. This package is mounted in a plastic SOP (Small Outline Package) for high density applications. The package has shield effect to cut off ambient light. FEATURES • Isolation distance (0.4 mm MIN.) • High isolation voltage (BV = 3 750 Vr.m.s.) • SOP (Small Outline Package) type • High-speed switching (tr = 4 µs TYP., tf = 5 µs TYP.) • Ordering number of taping product: PS2761-1-F3, F4 • UL approved: File No. E72422 (S) • BSI approved: No. 8436/8437 APPLICATIONS • Hybrid IC • Programmable logic controllers • Power supply Document No. PN10249EJ01V0DS (1st edition) (Previous No. P14143EJ3V0DS00) Date Published February 2003 CP(K) The mark shows major revised points. PS2761-1 PACKAGE DIMENSIONS (Unit: mm) 4±0.5 TOP VIEW 4 3 1. Anode 2. Cathode 3. Emitter 4. Collector 1 2 7.0±0.3 4.4 2.1±0.2 0.1±0.1 2.54 0.4 +0.10 –0.05 0.25 M 0.15 +0.10 –0.05 0.5±0.3 PHOTOCOUPLER CONSTRUCTION Parameter Air Distance Creepage Distance Isolation Distance Unit (MIN.) 5 mm 5 mm 0.4 mm 2 Data Sheet PN10249EJ01V0DS PS2761-1 ORDERING INFORMATION (Solder Contains Lead) Part Number PS2761-1 PS2761-1-F3 PS2761-1-F4 Package 4-pin SOP Packing Style Magazine case 100 pcs Embossed Tape 3 500 pcs/reel Application Part Number PS2761-1 *1 *1 For the application of the Safety Standard, following part number should be used. ORDERING INFORMATION (Pb-Free) Part Number PS2761-1-A PS2761-1-F3-A PS2761-1-F4-A Package 4-pin SOP Packing Style Magazine case 100 pcs Embossed Tape 3 500 pcs/reel Application Part Number PS2761-1 *1 *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherw ise specified) Parameter Diode Forward Current (DC) Reverse Voltage Power Dissipation Derating Power Dissipation Peak Forward Current Transistor *1 Symbol IF VR Ratings 50 6 0.8 80 1.0 40 5 40 1.5 150 3 750 –55 to +100 –55 to +150 Unit mA V mW/°C mW A V V mA mW/°C mW Vr.m.s. °C °C ∆PD/°C PD IFP VCEO VECO IC Collector to Emitter Voltage Emitter to Collector Voltage Collector Current Power Dissipation Derating Power Dissipation ∆PC/°C PC BV TA Tstg Isolation Voltage *2 Operating Ambient Temperature Storage Temperature *1 PW = 100 µs, Duty Cycle = 1 % *2 AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output Data Sheet PN10249EJ01V0DS 3 PS2761-1 ELECTRICAL CHARACTERISTICS (TA = 25 °C) Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Transistor Collector to Emitter Dark Current Coupled Current Transfer Ratio (IC/IF) *1 Symbol VF IR Ct ICEO IF = 5 m A VR = 5 V Conditions MIN. TYP. 1.1 MAX. 1.4 5 Unit V µA pF V = 0 V, f = 1 MHz IF = 0 mA, VCE = 40 V 15 100 nA CTR IF = 5 mA, VCE = 5 V 50 100 400 % Collector Saturation Voltage Isolation Resistance Isolation Capacitance Rise Time Fall Time *2 VCE (sat) IF = 10 mA, IC = 2 mA 11 0.3 V Ω RI-O CI-O tr tf VI-O = 1 kVDC V = 0 V, f = 1 MHz VCC = 5 V, IC = 2 mA, RL = 100 Ω 10 0.4 4 5 pF µs *2 *1 CTR rank K: 200 to 400 (%) M: 50 to 150 (%) L: 100 to 300 (%) N: 50 to 400 (%) *2 Test circuit for switching time Pulse Input PW = 100 µ s Duty cycle = 1/10 IF VCC In monitor 50 Ω RL = 100 Ω VOUT 4 Data Sheet PN10249EJ01V0DS PS2761-1 TYPICAL CHARACTERISTICS (TA = 25 °C, unless otherw ise specified) DIODE POWER DISSIPATION vs. AMBIENT TEMPERATURE Transistor Power Dissipation PC (mW) TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 210 180 150 120 90 60 30 0 25 50 75 100 100 Diode Power Dissipation PD (mW) 80 60 40 20 0 25 50 75 100 Ambient Temperature TA (˚C) Ambient Temperature TA ( ˚C) FORWARD CURRENT vs. FORWARD VOLTAGE 100 COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 35 30 IF = 25 mA 20 mA 15 mA 10 Collector Current IC (mA) Forward Current IF (mA) TA = +100 ˚C +60 ˚C +25 ˚C 25 20 15 10 5 5 mA 10 mA 1 0 ˚C –25 ˚C –50 ˚C 0.1 0.01 0.0 0.5 1.0 1.5 2.0 0 2 4 6 8 10 Forward Voltage VF (V) Collector to Emitter Voltage VCE (V) COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE Collector to Emitter Dark Current ICEO (nA) COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE 100 10 mA 5 mA 2 mA 10 000 1 000 VCE = 20 V 40 V Collector Current IC (mA) 10 100 1 IF = 1mA 10 1 –25 0 25 50 75 100 0.1 0.0 0.2 0.4 0.6 0.8 1.0 Ambient Temperature TA (˚C) Collector Saturation Voltage VCE(sat) (V) Data Sheet PN10249EJ01V0DS 5 ; ; NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE Normalized Current Transfer Ratio CTR PS2761-1 CURRENT TRANSFER RATIO vs. FORWARD CURRENT 1.4 1.2 400 Current Transfer Ratio CTR (%) 350 VCE = 5 V, n=3 300 250 200 150 100 50 1.0 0.8 0.6 0.4 0.2 Normalized to 1.0 at TA = 25 ˚C, IF = 5 mA, VCE = 5 V 50 75 0.0 –50 –25 0 25 100 0 0.1 1 10 100 Ambient Temperature TA (˚C) Forward Current IF (mA) SWITCHING TIME vs. LOAD RESISTANCE SWITCHING TIME vs. LOAD RESISTANCE IF = 1 mA, VCC = 5 V, CTR = 200 % tf 100 1 000 Switching Time t (µs) IC = 2 mA, VCC = 5 V, CTR = 200 % Switching Time t (µ s) 100 ts 10 tf tr 10 tr td td 1 1 10 ts 100 1k 10 k 0.1 10 100 1k 10 k 100 k Load Resistance RL (Ω) Load Resistance RL (Ω) FREQUENCY RESPONSE LONG TERM CTR DEGRADATION IF = 5 mA 1.2 1.0 0 CTR (Relative Value) Normalized Gain Gv –5 –10 –15 –20 –25 0.1 RL = 1 kΩ 100 Ω 0.8 0.6 0.4 0.2 0.0 IF = 1 mA, TA = 25 ˚C IF = 5 mA, TA = 25 ˚C IF = 20 mA, TA = 25 ˚C IF = 20 mA, TA = 60 ˚C 300 Ω 1 10 100 1 000 1 102 103 104 105 106 Frequency f (kHz) Time (Hr) Remark The graphs indicate nominal characteristics. 6 Data Sheet PN10249EJ01V0DS PS2761-1 TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Tape) 2.0±0.05 4.0±0.1 1.75±0.1 1.5+0.1 –0 2.9 MAX. 5.5±0.05 12.0±0.2 1.55±0.1 8.0±0.1 7.4±0.1 4.6±0.1 2.4±0.1 0.3 Tape Direction PS2761-1-F3 PS2761-1-F4 Outline and Dimensions (Reel) 2.0±0.5 φ 330±2.0 2.0±0.5 φ13.0±0.2 φ 100±1.0 R 1.0 φ 21.0±0.8 φ 13.0±0.2 13.5±1.0 17.5±1.0 Packing: 3 500 pcs/reel 11.9 to 15.4 Outer edge of flange Data Sheet PN10249EJ01V0DS 7 PS2761-1 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature • Time of temperature higher than 210 °C • Number of reflows • Flux 235 °C or below (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 100 to 160 ˚C 60 to 120 s (preheating) Time (s) (2) Dip soldering • Temperature • Time • Number of times • Flux 260 °C or below (molten solder temperature) 10 seconds or less One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between corrector-emitters at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings. 8 Data Sheet PN10249EJ01V0DS 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.