PS2801C-1-F3-K-A

PHOTOCOUPLER PS2801C-1,PS2801C-4 HIGH ISOLATION VOLTAGE SSOP PHOTOCOUPLER −NEPOC Series− DESCRIPTION The PS2801C-1 and PS2801C-4 are optically coupled isolators containing a GaAs light emitting diode and an NPN silicon phototransistor in a plastic SSOP for high density applications to realize an excellent cost performance. This package has shield effect to cut off ambient light. FEATURES • High isolation voltage (BV = 2 500 Vr.m.s.) • Small and thin package (4, 16-pin SSOP, Pin pitch 1.27 mm) • VCEO : 80 V PIN CONNECTION (Top View) • Ordering number of tape product: PS2801C-1-F3, F4, PS2801C-4-F3, F4 • Pb-Free product PS2801C-1 4 3 • Safety standards 1. Anode 2. Cathode 3. Emitter 4. Collector • UL approved: File No. E72422 • DIN EN60747-5-2 (VDE0884 Part2) approved (Option) 1 2 APPLICATIONS • Programmable logic controllers PS2801C-4 16 15 14 13 12 11 10 9 • Measuring instruments • Power supply • Hybrid IC 1 2 3 4 5 6 7 8 1. 3. 5. 7. 2. 4. 6. 8. 9. 11. 13. 15. 10. 12. 14. 16. Anode Cathode Emitter Collector Document No. PN10610EJ01V0DS (1st edition) Date Published May 2006 NS CP(K) 2006 PS2801C-1,PS2801C-4 PACKAGE DIMENSIONS (UNIT: mm) PS2801C-1 PS2801C-4 2.7±0.3 10.3±0.3 3 16 9 1 2 1 8 7.0±0.3 4.4 4.4 0.5±0.3 1.27 0.4±0.1 0.12 M 0.1±0.1 2.0+0.3 –0.2 0.15+0.10 –0.05 7.0±0.3 0.15+0.10 –0.05 2.0±0.1 0.1±0.1 4 0.40+0.10 –0.05 0.12 M 0.5±0.3 1.27 MARKING EXAMPLE PS2801C-4 PS2801C-1 1C Country Assembled 603 PS2801C-4 NL603 Assembly Lot *1 Last number of type No. : 1C N L 6 03 6 03 Week Assembled Year Assembled (Last 1 Digit) Week Assembled Year Assembled (Last 1 Digit) In-house Code (L: Pb-Free) *1 2 Assembly Lot No. 1 pin Mark : Pb-Free Rank Code Data Sheet PN10610EJ01V0DS PS2801C-1,PS2801C-4 ORDERING INFORMATION Part Number Order Number Solder Plating Specification Pb-Free Packing Style Safety Standard Approval PS2801C-1 PS2801C-1-A 50 pcs (Tape 50 pcs cut) Standard products PS2801C-1-F3 PS2801C-1-F3-A Embossed Tape 3 500 pcs/reel (UL approved) PS2801C-1-F4 PS2801C-1-F4-A PS2801C-4 PS2801C-4-A Magazine Case 45 pcs PS2801C-4-F3 PS2801C-4-F3-A Embossed Tape 2 500 pcs/reel PS2801C-4-F4 PS2801C-4-F4-A PS2801C-1-V PS2801C-1-V-A 50 pcs (Tape 50 pcs cut) DIN EN60747-5-2 PS2801C-1-V-F3 PS2801C-1-V-F3-A Embossed Tape 3 500 pcs/reel (VDE0884 Part2) PS2801C-1-V-F4 PS2801C-1-V-F4-A PS2801C-4-V PS2801C-4-V-A Magazine Case 45 pcs PS2801C-4-V-F3 PS2801C-4-V-F3-A Embossed Tape 2 500 pcs/reel PS2801C-4-V-F4 PS2801C-4-V-F4-A Application Part *1 Number PS2801C-1 PS2801C-4 PS2801C-1 Approved (Option) PS2801C-4 *1 For the application of the Safety Standard, following part number should be used. Data Sheet PN10610EJ01V0DS 3 PS2801C-1,PS2801C-4 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Symbol Ratings PS2801C-1 Diode Unit PS2801C-4 Forward Current (DC) IF 30 mA/ch Reverse Voltage VR 6 V Power Dissipation Derating Power Dissipation Peak Forward Current *1 ∆PD/°C 0.6 0.8 mW/°C PD 60 80 mW/ch IFP 0.5 A/ch Collector to Emitter Voltage VCEO 80 V Emitter to Collector Voltage VECO 5 V IC 30 mA/ch ∆PC/°C 1.2 mW/°C PC 120 mW/ch BV 2 500 Vr.m.s. Operating Ambient Temperature TA −55 to +100 °C Storage Temperature Tstg −55 to +150 °C Transistor Collector Current Power Dissipation Derating Power Dissipation Isolation Voltage *2 *1 PW = 100 µs, Duty Cycle = 1% *2 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output Pins 1-2 shorted together, 3-4 shorted together (PS2801C-1). Pins 1-8 shorted together, 9-16 shorted together (PS2801C-4). 4 Data Sheet PN10610EJ01V0DS PS2801C-1,PS2801C-4 ELECTRICAL CHARACTERISTICS (TA = 25°C) Parameter Diode Symbol Conditions Forward Voltage VF IF = 5 mA Reverse Current IR VR = 5 V Terminal Capacitance Ct V = 0 V, f = 1.0 MHz Transistor Collector to Emitter Dark Current ICEO VCE = 80 V, IF = 0 mA Coupled Current Transfer Ratio *1 (IC/IF) CTR IF = 5 mA, VCE = 5 V Collector Saturation Voltage VCE (sat) IF = 10 mA, IC = 2 mA Isolation Resistance RI-O VI-O = 1.0 kVDC Isolation Capacitance CI-O V = 0 V, f = 1.0 MHz *2 tr Rise Time Fall Time *2 VCC = 5 V, IC = 2 mA, RL = 100 Ω tf MIN. TYP. MAX. Unit 1.2 1.4 V 5 µA 10 50 0.13 10 pF 100 nA 400 % 0.3 V Ω 11 0.4 pF 5 µs 7 *1 CTR rank PS2801C-1 N : 50 to 400 (%) P : 150 to 300 (%) L : 100 to 300 (%) M : 100 to 400 (%) PS2801C-4 N : 50 to 400 (%) M : 100 to 400 (%) *2 Test circuit for switching time VCC Pulse Input PW = 100 µ s Duty Cycle = 1/10 IF VOUT 50 Ω RL = 100 Ω Data Sheet PN10610EJ01V0DS 5 PS2801C-1,PS2801C-4 TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified) DIODE POWER DISSIPATION vs. AMBIENT TEMPERATURE TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Transistor Power Dissipation PC (mW) Diode Power Dissipation PD (mW) 100 80 PS2801C-4 60 0.8 mW/˚C PS2801C-1 40 0.6 mW/˚C 20 0 0 25 50 75 100 125 PS2801C-1 PS2801C-4 120 1.2 mW/˚C 80 40 0 0 25 50 75 100 125 Ambient Temperature TA (˚C) FORWARD CURRENT vs. FORWARD VOLTAGE COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 30 TA = +100˚C +60˚C +25˚C Collector Current IC (mA) Forward Current IF (mA) 160 Ambient Temperature TA (˚C) 100 50 200 10 5 0˚C –25˚C –55˚C 1 0.5 CTR = 250% IF = 10 mA 25 20 5 mA 15 10 2 mA 5 1 mA 0.1 Collector to Emitter Dark Current ICEO (nA) 0.05 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 0 0 1.5 4 6 8 10 Forward Voltage VF (V) Collector to Emitter Voltage VCE (V) COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE 10 10 000 IF = 10 mA Collector Current IC (mA) 5 mA VCE = 80 V 1 000 70 V 100 24 V 10 1 0 25 50 CTR = 200% 75 100 2 mA 1 mA 1 0.1 0 0.2 0.4 0.6 CTR = 250% 0.8 1.0 Collector Saturation Voltage VCE(sat) (V) Ambient Temperature TA (˚C) Remark The graphs indicate nominal characteristics. 6 2 Data Sheet PN10610EJ01V0DS PS2801C-1,PS2801C-4 CURRENT TRANSFER RATIO vs. FORWARD CURRENT 1.4 Current Transfer Ratio CTR (%) 1.2 1.0 80% 0.8 0.6 0.4 Normalized to 1.0 0.2 at TA = 25˚C, IF = 5 mA, VCE = 5 V 0 –75 –50 –25 0 100 Switching Time t (µ s) 400 CTR = 250% 25 50 75 VCE = 5 V, n=3 300 Sample A B C 200 100 0 0.01 100 0.1 1 10 Ambient Temperature TA (˚C) Forward Current IF (mA) SWITCHING TIME vs. LOAD RESISTANCE SWITCHING TIME vs. LOAD RESISTANCE 100 1 000 IC = 2 mA, VCC = 5 V, CTR = 228% IF = 5 mA, VCC = 5 V, CTR = 228% tf Switching Time t (µs) Normalized Current Transfer Ratio CTR NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE tr 10 td ts 1 tf 100 ts 10 tr td 0.1 10 100 1 000 1 1 10 000 10 100 Load Resistance RL (kΩ) Load Resistance RL (Ω) LONG TERM CTR DEGRADATION FREQUENCY RESPONSE 5 1.2 0 1.0 CTR (Relative Value) Normalized Gain Gv TYP. 100 Ω –5 RL = 1 kΩ –10 –15 300 Ω –20 IF = 5 mA, VCE = 5 V –25 0.1 1 10 0.8 IF = 5 mA, TA = 25˚C IF = 20 mA, TA = 25˚C 0.6 IF = 5 mA, TA = 60˚C 0.4 0.2 100 1 000 0 10 102 103 104 105 Time (Hr) Frequency f (kHz) Remark The graphs indicate nominal characteristics. Data Sheet PN10610EJ01V0DS 7 PS2801C-1,PS2801C-4 TAPING SPECIFICATIONS (UNIT: mm) φ 1.5+0.1 –0 7.5±0.1 4.0±0.1 16.0±0.3 2.0±0.1 7.55±0.1 1.75±0.1 Outline and Dimensions (Tape) 2.8 MAX. 0.3 1.55±0.1 2.3±0.1 2.85±0.1 4.0±0.1 Tape Direction 1C 603 1C 603 1C 603 1C 603 1C 603 1C 603 1C 603 1C 603 1C 603 PS2801C-1-F4 1C 603 PS2801C-1-F3 Outline and Dimensions (Reel) R 1.0 φ 21.0±0.8 φ 100±1.0 2.0±0.5 φ13.0±0.2 φ 330±2.0 2.0±0.5 17.5±1.0 21.5±1.0 Packing: 3 500 pcs/reel 8 Data Sheet PN10610EJ01V0DS 15.9 to 19.4 Outer edge of flange PS2801C-1,PS2801C-4 2.8 MAX. 10.7±0.1 7.5±0.1 φ 1.5+0.1 –0 16.0±0.3 2.0±0.1 4.0±0.1 1.75±0.1 Outline and Dimensions (Tape) 0.3 2.3±0.1 8.3±0.1 1.55±0.1 12.0±0.1 Tape Direction PS2801C-4-F3 PS2801C-4-F4 Outline and Dimensions (Reel) 2.0±0.5 φ 21.0±0.8 φ 100±1.0 R 1.0 φ 330±2.0 2.0±0.5 φ13.0±0.2 17.5±1.0 21.5±1.0 Packing: 2 500 pcs/reel Data Sheet PN10610EJ01V0DS 15.9 to 19.4 Outer edge of flange 9 PS2801C-1,PS2801C-4 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature 260°C or below (package surface temperature) • Time of peak reflow temperature 10 seconds or less • Time of temperature higher than 220°C 60 seconds or less • Time to preheat temperature from 120 to 180°C 120±30 s • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Package Surface Temperature T (˚C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260˚C MAX. 220˚C to 60 s 180˚C 120˚C 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature 260°C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120°C or below (package surface temperature) • Number of times One (Allowed to be dipped in solder including plastic mold portion.) • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron • Peak Temperature (lead part temperature) 350°C or below • Time (each pins) 3 seconds or less • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100°C 10 Data Sheet PN10610EJ01V0DS PS2801C-1,PS2801C-4 (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. 3. Measurement conditions of current transfer ratios (CTR), which differ according to photocoupler Check the setting values before use, since the forward current conditions at CTR measurement differ according to product. When using products other than at the specified forward current, the characteristics curves may differ from the standard curves due to CTR value variations or the like. This tendency may sometimes be obvious, especially below IF = 1 mA. Therefore, check the characteristics under the actual operating conditions and thoroughly take variations or the like into consideration before use. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Data Sheet PN10610EJ01V0DS 11 PS2801C-1,PS2801C-4 • The information in this document is current as of May, 2006. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. • NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. • NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 12 Data Sheet PN10610EJ01V0DS PS2801C-1,PS2801C-4 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. For further information, please contact NEC Compound Semiconductor Devices Hong Kong Limited E-mail: contact@ncsd-hk.necel.com Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209 NEC Electronics (Europe) GmbH http://www.eu.necel.com/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 Compound Semiconductor Devices Division NEC Electronics Corporation URL: http://www.ncsd.necel.com/ 0604 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.