PS9214-A

PHOTOCOUPLER PS9214 HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER NEPOC Series FOR CREEPAGE DISTANCE OF 5.5 mm DESCRIPTION The PS9214 is an optically coupled high-speed, isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9214 is designed specifically for high common mode transient immunity (CMR) and low pulse width distortion with operating temperature. FEATURES • Long creepage distance (5.5 mm MIN.) • High common mode transient immunity (CM H, CML = 20 kV/ s TYP.) • Pulse width distortion ( tPHL tPLH = 3 ns TYP.) • High-speed (10 Mbps) • High isolation voltage (BV = 2 500 Vr.m.s.) • Open collector output • Ordering number of taping product: PS9214-F3, F4: 2 500 pcs/reel • Pb-Free product • Safety standards • UL approved: File No. E72422 • DIN EN60747-5-2 (VDE0884 Part2) approved No.40008347 (Option) TRUTH TABLE APPLICATIONS LED Output • Measurement equipment ON L OFF H • PDP • FA Network Document No. PN10536EJ04V0DS (4th edition) Date Published August 2008 NS The mark shows major revised points. The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field. PS9214 PACKAGE DIMENSIONS (UNIT: mm) MARKING EXAMPLE 2 Data Sheet PN10536EJ04V0DS PS9214 ORDERING INFORMATION Part Number Order Number Solder Plating Packing Style Specification Safety Standard Application Part Approval Number*1 PS9214 PS9214-A Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9214-F3 PS9214-F3-A (SnBi) Embossed Tape 2 500 pcs/reel (UL approved) PS9214-F4 PS9214-F4-A PS9214-V PS9214-V-A 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9214-V-F3 PS9214-V-F3-A Embossed Tape 2 500 pcs/reel (VDE0884 Part2) PS9214-V-F4 PS9214-V-F4-A PS9214 PS9214-AX Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9214-F3 PS9214-F3-AX (Ni/Pd/Au) Embossed Tape 2 500 pcs/reel (UL approved) PS9214-F4 PS9214-F4-AX PS9214-V PS9214-V-AX 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9214-V-F3 PS9214-V-F3-AX Embossed Tape 2 500 pcs/reel (VDE0884 Part2) PS9214-V-F4 PS9214-V-F4-AX PS9214 approved (Option) approved (Option) *1 For the application of the Safety Standard, following part number should be used. Data Sheet PN10536EJ04V0DS 3 PS9214 ABSOLUTE MAXIMUM RATINGS (T A = 25 C, unless otherwise specified) Parameter Symbol Ratings Unit IF 30 mA Reverse Voltage VR 5 V Supply Voltage VCC 7 V Output Voltage VO 7 V IO 25 mA PC 40 mW Isolation Voltage BV 2 500 Vr.m.s. Operating Ambient Temperature TA 40 to +85 C Storage Temperature Tstg 55 to +125 C Diode Detecto Forward Current *1 r Output Current *2 Power Dissipation *3 *1 Reduced to 0.3 mA/ C at TA = 25 C or more. *2 Applies to output pin V O. Reduced to 1.5 mW/ C at TA = 65 C or more. *3 AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. Low Level Input Voltage VFL 0 High Level Input Current IFH 6.3 Supply Voltage VCC 4.5 TTL (RL = 1 k , loads) N Pull-up resistor RL 4 TYP. MAX. Unit 0.8 V 10 12.5 mA 5.0 5.5 V 5 330 4k Data Sheet PN10536EJ04V0DS PS9214 ELECTRICAL CHARACTERISTICS (T A = 40 to +85°C, unless otherwise specified) Diode Detector Forward Voltage VF IF = 10 mA, TA = 25 C Reverse Current IR VR = 3 V, TA = 25 C Terminal Capacitance Ct VF = 0 V, f = 1 MHz, T A = 25 C IOH VCC = VO = 5.5 V, VF = 0.8 V 0.02 250 A Low Level Output Voltage VOL VCC = 5.5 V, IF = 5 mA, IOL = 13 mA 0.15 0.6 V High Level Supply Current ICCH VCC = 5.5 V, IF = 0 mA, VO = open 3 8 mA Low Level Supply Current ICCL VCC = 5.5 V, IF = 10 mA, VO = open 7 11 mA Threshold Input Current IFHL VCC = 5 V, VO = 0.8 V, RL = 350 2 5 mA Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25 C Isolation Capacitance CI-O VI-O = 0 V, f = 1 MHz, T A = 25 C Propagation Delay Time tPHL *2 Coupled (H (H 1.4 1.65 MAX. Unit 1.9 V 10 A 30 pF L) *3 L) Propagation Delay Time (L MIN. *1 Symbol High Level Output Current Conditions TYP. Parameter tPLH H) 0.6 TA = 25 C VCC = 5 V, RL = 350 *3 1011 54 , IF = 7.5 mA , IF = 7.5 mA 75 ns 100 TA = 25 C VCC = 5 V, RL = 350 pF 51 75 ns 100 Rise Time tr VCC = 5 V, RL = 350 , IF = 7.5 mA 20 Fall Time tf VCC = 5 V, RL = 350 , IF = 7.5 mA 10 tPHL tPLH VCC = 5 V, RL = 350 , IF = 7.5 mA 3 Propagation Delay Skew tPSK VCC = 5 V, RL = 350 , IF = 7.5 mA Common Mode Transient Immunity at High *4 Level Output CM H RL = 350 , TA = 25 C, IF = 0 mA, VO (MIN.) = 2 V, VCM = 1 kV 10 20 kV/ s Common Mode Transient Immunity at Low *4 Level Output CM L RL = 350 , TA = 25 C, IF = 7.5 mA, VO (MAX.) = 0.8 V, VCM = 1 kV 10 20 kV/ s Pulse Width Distortion 50 ns *3 (PWD) Data Sheet PN10536EJ04V0DS 60 5 PS9214 *1 Typical values at TA = 25 C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of V CC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *3 Test circuit for propagation delay time Remark CL includes probe and stray wiring capacitance. *4 Test circuit for common mode transient immunity Remark CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 F is used between V CC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. 6 Data Sheet PN10536EJ04V0DS PS9214 TYPICAL CHARACTERISTICS (T A = 25 C, unless otherwise specified) Remark The graphs indicate nominal characteristics. Data Sheet PN10536EJ04V0DS 7 PS9214 Remark The graphs indicate nominal characteristics. 8 Data Sheet PN10536EJ04V0DS PS9214 TAPING SPECIFICATIONS (UNIT: mm) Data Sheet PN10536EJ04V0DS 9 PS9214 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) 10 Data Sheet PN10536EJ04V0DS PS9214 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature 260 C or below (package surface temperature) • Time of peak reflow temperature 10 seconds or less • Time of temperature higher than 220 C 60 seconds or less • Time to preheat temperature from 120 to 180 C 120 30 s • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (2) Wave soldering • Temperature 260 C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120 C or below (package surface temperature) • Number of times One (Allowed to be dipped in solder including plastic mold portion.) • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron • Peak Temperature (lead part temperature) 350 C or below • Time (each pins) 3 seconds or less • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100 C Data Sheet PN10536EJ04V0DS 11 PS9214 (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. 12 Data Sheet PN10536EJ04V0DS PS9214 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Speck Unit Application classification (DIN EN 60664-1 VDE0110 Part 1) for rated line voltages for rated line voltages 300 Vr.m.s. 600 Vr.m.s. IV III Climatic test class (DIN EN 60664-1 VDE0110) 40/100/21 Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) Upr = 1.5 UIORM, Pd UIORM, Pd 707 1 061 Vpeak Vpeak Upr 1 326 Vpeak UTR 6 000 Vpeak 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 UIORM Upr 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) 2 Clearance distance 4.0 mm Creepage distance 4.0 mm Comparative tracking index (DIN IEC 112/VDE 0303 Part 1) CTI Material group (DIN EN 60664-1 VDE0110 Part 1) 175 III a Storage temperature range Tstg –55 to +125 °C Operating temperature range TA –40 to +85 °C Ris MIN. Ris MIN. 1012 1011 Tsi 150 °C Isi Psi 150 600 mA mW Ris MIN. 109 Isolation resistance, minimum value VIO = 500 V dc at T A = 25°C VIO = 500 V dc at T A MAX. at least 100°C Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Current (input current IF, Psi = 0) Power (output or total power dissipation) Isolation resistance VIO = 500 V dc at T A = Tsi Data Sheet PN10536EJ04V0DS 13 PS9214 14 Data Sheet PN10536EJ04V0DS PS9214 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth.