UPA811T-T1-A

NPN SILICON HIGH FREQUENCY TRANSISTOR FEATURES • • • • SMALL PACKAGE STYLE: 2 NE680 Die in a 2 mm x 1.25 mm package LOW NOISE FIGURE: NF = 1.9 dB TYP at 2 GHz HIGH GAIN: |S21E|2 = 7.5 dB TYP at 2 GHz EXCELLENT LOW VOLTAGE, LOW CURRENT PERFORMANCE 2.0 ± 0.2 1.3 2 0.65 1 UPA811T OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S06 (Top View) 2.1 ± 0.1 1.25 ± 0.1 6 0.2 (All Leads) 5 DESCRIPTION NEC's UPA811T is two NPN high frequency silicon epitaxial transistors encapsulated in an ultra small 6 pin SMT package. Each transistor is independently mounted and easily configured for either dual transistor or cascode operation. The high fT, low voltage bias and small size make this device ideally suited for pager and other hand-held wireless applications. 3 4 0.9 ± 0.1 0.7 0.15 - 0.05 0 ~ 0.1 +0.10 ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS VCBO VCEO VEBO IC PT PARAMETERS Collector to Base Voltage Collector to Emitter Voltage Emitter to Base Voltage Collector Current Total Power Dissipation 1 Die 2 Die Junction Temperature Storage Temperature UNITS V V V mA mW mW °C °C RATINGS 20 10 1.5 35 110 200 150 -65 to +150 TJ TSTG PIN OUT 1. Collector Transistor 1 2. Base Transistor 2 3. Collector Transistor 2 4. Emitter Transistor 2 5. Emitter Transistor 1 6. Base Transistor 1 Note: Pin 3 is identified with a circle on the bottom of the package. Note: 1. Operation in excess of any one of these parameters may result in permanent damage. ELECTRICAL CHARACTERISTICS (TA = 25°C) PART NUMBER PACKAGE OUTLINE SYMBOLS ICBO IEBO hFE1 fT Cre2 |S21E|2 NF PARAMETERS AND CONDITIONS Collector Cutoff Current at VCB = 10 V, IE = 0 Emitter Cutoff Current at VEB = 1 V, IC = 0 Forward Current Gain at VCE = 3 V, IC = 5 mA Gain Bandwidth at VCE = 3 V, IC = 5 mA Feedback Capacitance at VCB = 3 V, IE = 0, f = 1 MHz Insertion Power Gain at VCE = 3 V, IC = 5 mA, f = 2 GHz Noise Figure at VCE = 3 V, IC = 5 mA, f = 2 GHz GHz pF dB dB 5.5 UNITS µA µA 80 5.5 120 8.0 0.3 7.5 1.9 3.2 0.7 MIN UPA811T S06 TYP MAX 1.0 1.0 200 Notes: 1.Pulsed measurement, pulse width ≤ 350 µs, duty cycle ≤ 2 %. 2.The emitter terminal should be connected to the ground terminal of the 3 terminal capacitance bridge. For Tape and Reel version use part number UPA811T-T1, 3K per reel. California Eastern Laboratories UPA811T TYPICAL PERFORMANCE CURVES (TA = 25°C) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE 25 COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE 160 µA Total Power Dissipation, PT (mW) Free Air 200 El Collector Current, IC (mA) 2 em 20 140 µA 120 µA en ts Pe in rE lem To t al 15 en 100 µA 80 µA t 100 10 60 µA 40 µA 5 lB=20 µA 0 50 100 150 0 0.5 1.0 Ambient Temperature, TA (°C) Collector to Emitter Voltage, VCE (V) COLLECTOR CURRENT vs. BASE TO EMITTER VOLTAGE 20 VCE = 3 V 200 DC CURRENT GAIN vs. COLLECTOR CURRENT VCE = 3 V Collector Current, IC (mA) DC Current Gain, hFE 0.5 1.0 100 50 10 20 10 0 0.5 1 5 10 50 Base to Emitter Voltage, VBE (V) Collector Current, IC (mA) FEEDBACK CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE 5.0 GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 10 Gain Bandwidth Product, fT (GHz) f = 1 MHz Feddback Capacitance, CRE (pF) VCE = 3 V f = 2 GHz 8 2.0 1.0 6 0.5 4 0.2 2 0.1 1 2 5 10 20 50 0 0.5 1 5 10 50 Collector to Base Voltage, VCB (V) Collector Current, IC (mA) UPA811T TYPICAL PERFORMANCE CURVES (TA = 25°C) INSERTION POWER GAIN vs. COLLECTOR CURRENT 12 INSERTION POWER GAIN vs. FREQUENCY 25 VCE = 3 V lc = 5 mA 20 Insertion Power Gain, IS21eI2 (dB) 8 Insertion Power Gain, IS21eI2 (dB) VCE = 3 V f = 2 GHz 15 10 4 5 0 0.5 1 5 10 50 0 0.1 0.2 0.5 1.0 2.0 5.0 Collector Current, lC (mA) Frequency, f (GHz) NOISE FIGURE vs. COLLECTOR CURRENT 5 VCE = 3 V f = 2 GHz Noise Figure, NF (dB) 4 3 2 1 0 0.5 1 5 10 50 Collector Current, lC (mA) ORDERING INFORMATION PART NUMBER UPA811T-T1-A QUANTITY 3000 PACKAGING Tape & Reel Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM PRINTED IN USA ON RECYCLED PAPER -1/99 DATA SUBJECT TO CHANGE WITHOUT NOTICE 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.