UPC8233TK-E2

PRELIMINARY PRODUCT INFORMATION BIPOLAR ANALOG INTEGRATED CIRCUIT μPC8233TK SiGe:C LOW NOISE AMPLIFIER FOR GPS/MOBILE COMMUNICATIONS DESCRIPTION The μPC8233TK is a silicon germanium carbon (SiGe:C) monolithic integrated circuit designed as low noise amplifier for GPS and mobile communications. This device exhibits low noise figure and high power gain characteristics. This device is suitable for the reduction in power consumption of the mobile communication system because it operates by low voltage and low current. The package is 6-pin lead-less minimold, suitable for surface mount. This IC is manufactured using our UHS4 (Ultra High Speed Process) SiGe:C bipolar process. FEATURES • Supply voltage • Low noise • High gain • Low current consumption • Built-in power-saving function • High-density surface mounting • Included protection circuits for ESD : VCC = 1.7 to 3.3 V (2.7 V TYP.) : NF = 0.90 dB TYP. @ VCC = 2.7 V, fin = 1575 MHz NF = 0.90 dB TYP. @ VCC = 1.8 V, fin = 1575 MHz : GP = 20 dB TYP. @ VCC = 2.7 V, fin = 1575 MHz GP = 19.5 dB TYP. @ VCC = 1.8 V, fin = 1575 MHz : ICC = 3.5 mA TYP. @ VCC = 2.7 V VPSon = 1.0V to Vcc VPSoff = 0.0 to 0.4V : 6-pin lead-less minimold package (1.5 × 1.1 × 0.55 mm) • Included very robust bandgap regulator (Small VCC and TA dependence) APPLICATION • Low noise amplifier for GPS and mobile communications ORDERING INFORMATION Part Number Order Number Package 6-pin lead-less minimold (1511 PKG) (Pb-Free) Marking TBD Supplying Form • 8 mm wide embossed taping • Pin 1, 6 face the perforation side of the tape • Qty 5 kpcs/reel μPC8233TK-E2 μPC8233TK-E2-A Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: μPC8233TK Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Document No. (1st edition) Date Published January 2007 NS CP(N) © NEC Electronics Corporation 2007 μPC8233TK PIN CONNECTIONS Pin No. 1 2 3 4 5 6 Pin Name INPUT GND Power Save OUTPUT GND VCC INTERNAL BLOCK DIAGRAM INPUT 1 6 VCC GND 2 5 GND Bias Power Save 3 4 OUTPUT ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Power-Saving Voltage Power Dissipation Operating Ambient Temperature Storage Temperature Input Power Symbol VCC VPS PD TA Tstg Pin Test Conditions TA = +25° C TA = +25° C TA = +85°C Note Ratings 4.0 4.0 232 −40 to +85 −55 to +150 +10 Unit V V mW °C °C dBm Note Mounted on double-side copper-clad 50 × 50 × 1.6 mm epoxy glass PWB RECOMMENDED OPERATING RANGE Parameter Supply Voltage Operating Ambient Temperature Power Save Turn-on Voltage Power Save Turn-off Voltage Symbol VCC TA VPSon VPSoff MIN. 1.7 −40 1.0 0 TYP. 2.7 +25 − − MAX. 3.3 +85 VCC 0.4 Unit V °C V V 2 μPC8233TK ELECTRICAL CHARACTERISTICS (TA = +25° C, VCC = VPS = 2.7 V, fin = 1575 MHz, unless otherwise specified) Parameter Circuit Current Symbol ICC No Signal Test Conditions (VPS = 2.7 V) MIN. 2.5 − 17.5 − fin1 = 1574 MHz, fin2 = 1575 MHz − TYP. 3.5 − 20 0.9 −7.5 MAX. 4.8 1 22.5 1.2 − − − − − Unit mA At Power-Saving Mode (VPS = 0 V) Power Gain Noise Figure Input 3rd Order Distortion Intercept Point Input Return Loss Output Return Loss Isolation Gain 1 dB Compression Input Power RLin RLout ISL Pin (1 dB) GP NF IIP3 Pin = −35 dBm μA dB dB dBm 7 8 − − 16 16 36 −23 dB dB dB dBm STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25° C, VCC = VPS = 1.8 V, fin = 1575 MHz, unless otherwise specified) Parameter Circuit Current Symbol ICC No Signal Test Conditions (VPS = 1.8 V) Reference 3.3 − 19.5 0.9 fin1 = 1574 MHz, fin2 = 1575 MHz −8 Unit mA At Power-Saving Mode (VPS = 0 V) Power Gain Noise Figure Input 3rd Order Distortion Intercept Point Input Return Loss Output Return Loss Isolation Gain 1 dB Compression Input Power RLin RLout ISL Pin (1 dB) GP NF IIP3 Pin = −35 dBm μA dB dB dBm 16 15.5 36 −23.5 dB dB dB dBm TEST CIRCUIT 22nF 8.2nH IN Vcc 1000pF 1.2pF GND GND 18nH Power Save OUT 360 6.8nH 18pF 3 μPC8233TK PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm) (Top View) (Bottom View) 0.48±0.05 0.48±0.05 1.5±0.1 1.1±0.1 1.3±0.05 0.2±0.1 0.16±0.05 0.9±0.1 4 0.55±0.03 0.11+0.1 –0.05 μPC8233TK NOTES ON CORRECT USE (1) Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation). All the ground terminals must be connected together with wide ground pattern to decrease impedance difference. (3) The bypass capacitor should be attached to VCC line. (4) Do not supply DC voltage to INPUT pin. RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220° C or higher Preheating time at 120 to 180° C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260° C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 260 ° C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350° C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260 For soldering Preheating temperature (package surface temperature) : 120° C or below Caution Do not use different soldering methods together (except for partial heating). 5 μPC8233TK 6 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.