UPG2158T5K

GaAs INTEGRATED CIRCUIT µPG2158T5K L, S-BAND SPDT SWITCH DESCRIPTION The µPG2158T5K is a GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which was developed for mobile phone and another L, S-band application. This device can operate 2 control switching by control voltage 1.8 to 5.3 V. This device can operate frequency from 0.05 to 3.0 GHz, having the low insertion loss and high isolation. This device is housed in a 6-pin plastic TSSON (Thin Shrink Small Out-line Non-leaded) package. And this package is able to high-density surface mounting. FEATURES • Switch control voltage • : Vcont (H) = 1.8 to 5.3 V (2.7 V TYP.) : Vcont (L) = −0.2 to +0.2 V (0 V TYP.) Low insertion loss : LINS1 = 0.40 dB TYP. @ f = 0.05 to 1.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : LINS2 = 0.45 dB TYP. @ f = 1.0 to 2.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : LINS3 = 0.47 dB TYP. @ f = 2.0 to 2.5 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : LINS4 = 0.53 dB TYP. @ f = 2.5 to 3.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V High isolation : ISL1 = 27 dB TYP. @ f = 0.05 to 1.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : ISL2 = 19 dB TYP. @ f = 1.0 to 2.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : ISL3 = 17 dB TYP. @ f = 2.0 to 2.5 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : ISL4 = 17 dB TYP. @ f = 2.5 to 3.0 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V Handling power : Pin (0.1 dB) = +29.0 dBm TYP. @ f = 2.0/2.5 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V : Pin (1 dB) = +30.5 dBm TYP. @ f = 2.0/2.5 GHz, Vcont (H) = 2.7 V, Vcont (L) = 0 V High-density surface mounting : 6-pin plastic TSSON package (1.0 × 1.0 × 0.37 mm) • • • APPLICATIONS • L, S-band digital cellular or cordless telephone TM • W-LAN, WLL and Bluetooth etc. ORDERING INFORMATION Part Number Order Number Package 6-pin plastic TSSON (Pb-Free) Note Marking G2 Supplying Form • Embossed tape 8 mm wide • Pin 1, 6 face the perforation side of the tape • Qty 5 kpcs/reel µPG2158T5K-E2 µPG2158T5K-E2-A Note With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales office. Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: µPG2158T5K-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. Document No. PG10578EJ02V0DS (2nd edition) Date Published December 2005 CP(K) The mark shows major revised points. µPG2158T5K PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) 1 6 (Top View) 1 6 6 (Bottom View) 1 Pin No. 1 2 3 Pin Name OUTPUT1 GND OUTPUT2 Vcont2 INPUT Vcont1 G2 Vcont1 Low High Parameter Parameter 2 5 2 5 5 2 4 5 6 3 4 3 4 4 3 TRUTH TABLE Vcont2 High Low INPUT−OUTPUT1 OFF ON INPUT−OUTPUT2 ON OFF ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherw ise specified) Symbol Vcont Pin TA Tstg Ratings +6.0 Note Unit V dBm °C °C Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature +31 −45 to +85 −55 to +150 Note ⎪Vcont1 − Vcont2⎪ ≤ 6.0 V RECOMMENDED OPERATING RANGE (TA = +25°C, unless otherw ise specified) Symbol Vcont (H) Vcont (L) MIN. 1.8 −0.2 TYP. 2.7 0 MAX. 5.3 +0.2 Unit V V Switch Control Voltage (H) Switch Control Voltage (L) 2 Data Sheet PG10578EJ02V0DS µPG2158T5K ELECTRICAL CHARACTERISTICS 1 (TA = +25°C, Vcont (H) = 2.7 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, unless otherwise specified) Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Input Return Loss Output Return Loss 0.1 dB Loss Compression Input Power Note 2 Symbol LINS1 LINS2 LINS3 LINS4 ISL1 ISL2 ISL3 ISL4 RLin RLout Pin (0.1 dB) Test Conditions f = 0.05 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 3.0 GHz f = 0.05 to 3.0 GHz f = 2.0/2.5 GHz f = 0.5 to 3.0 GHz Note 1 Note 1 Note 1 Note 1 MIN. − − − − 23 16 14 14 15 15 +26.0 − − TYP. 0.40 0.45 0.47 0.53 27 19 17 17 20 20 +29.0 +29.0 +30.5 MAX. 0.45 0.50 0.55 0.60 − − − − − − − − − − − − Unit dB dB dB dB dBm 1 dB Loss Compression Input Power Note 3 Pin (1 dB) f = 0.5 to 3.0 GHz dBm 2nd Harmonics 3rd Harmonics Input 3rd Order Distortion Intercept Point Switch Control Current Switch Control Speed 2f0 3 f0 IIP3 f = 2.0/2.5 GHz, Pin = +20 dBm f = 2.0/2.5 GHz, Pin = +20 dBm f = 0.5 to 3.0 GHz 2 tone 5 MHz spacing 65 65 − − − 75 75 +60 dBc dBc dBm Icont tSW No signal 50% CTL to 90/10% RF 0.2 50 20 500 µA ns Notes 1. DC cut capacitors = 1 000 pF at f = 0.05 to 0.5 GHz 2. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. 3. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors. The value of DC cut capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of recommended DC cut capacitor value is less than 100 pF. Data Sheet PG10578EJ02V0DS 3 µPG2158T5K ELECTRICAL CHARACTERISTICS 2 (TA = +25°C, Vcont (H) = 1.8 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, unless otherwise specified) Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Input Return Loss Output Return Loss 0.1 dB Loss Compression Input Power Note 2 Symbol LINS1 LINS2 LINS3 LINS4 ISL1 ISL2 ISL3 ISL4 RLin RLout Pin (0.1 dB) Test Conditions f = 0.05 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.05 to 3.0 GHz f = 0.05 to 3.0 GHz f = 2.0/2.5 GHz f = 0.5 to 3.0 GHz Note 1 Note 1 Note 1 Note 1 MIN. − − − − 23 16 14 14 15 15 +19.0 − − − − TYP. 0.40 0.46 0.48 0.54 27 19 17 17 20 20 +22.0 +22.0 +25.0 MAX. 0.47 0.52 0.57 0.62 − − − − − − − − − Unit dB dB dB dB dBm 1 dB Loss Compression Input Power Note 3 Pin (1 dB) f = 0.5 to 3.0 GHz dBm Switch Control Current Switch Control Speed Icont tSW No signal 50% CTL to 90/10% RF 0.2 50 20 500 µA ns Notes 1. DC cut capacitors = 1 000 pF at f = 0.05 to 0.5 GHz 2. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. 3. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors. The value of DC cut capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. The range of recommended DC cut capacitor value is less than 100 pF. 4 Data Sheet PG10578EJ02V0DS µPG2158T5K EVALUATION CIRCUIT Vcont1 INPUT Vcont2 1 000 pF C0 1 000 pF 6 5 4 1 2 GND 3 C0 C0 OUTPUT1 OUTPUT2 Remark C0 : 0.05 to 0.5 GHz 1 000 pF : 0.5 to 3.0 GHz 56 pF The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. Data Sheet PG10578EJ02V0DS 5 µPG2158T5K ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Vcont2 OUTPUT2 C 5 INPUT C1 G2 C 4 C C 3 2 OUTPUT1 Vcont1 USING THE NEC EVALUATION BOARD Symbol C1, C2, C3 C4, C5 Values 56 pF 1 000 pF 6 Data Sheet PG10578EJ02V0DS µPG2158T5K TYPICAL CHARACTERISTICS (TA = +25°C, Vcont (H) = 2.7 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, using test fixture, unless otherw ise specified) INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY 2.5 2.0 Insertion Loss LINS (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY 2.5 2.0 Insertion Loss LINS (dB) 1: 2: 3: 4: 5: –0.380 dB 1.0 GHz –0.411 dB 1.5 GHz –0.442 dB 2.0 GHz –0.468 dB 2.5 GHz –0.513 dB 3.0 GHz –0.380 dB 1.0 GHz –0.413 dB 1.5 GHz 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –2.5 0.5 1.1 1.7 2.3 1 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –0.446 dB 2.0 GHz –0.468 dB 2.5 GHz –0.511 dB 3.0 GHz 1 2 3 4 5 2 3 4 5 2.9 3.5 –2.5 0.5 1.1 1.7 2.3 2.9 3.5 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 1: 2: 3: 4: 5: –27.327 dB 1.0 GHz –23.924 dB 1.5 GHz –21.519 dB 2.0 GHz –19.691 dB 2.5 GHz –18.176 dB 3.0 GHz –27.239 dB 1.0 GHz –23.849 dB 1.5 GHz –21.47 dB 2.0 GHz 20 10 0 –10 –20 –30 –40 –50 0.5 1.1 1.7 2.3 1 3 4 20 10 0 –10 –20 –30 –40 1 3 –19.834 dB 2.5 GHz –18.109 dB 3.0 GHz 5 2 2 4 5 2.9 3.5 –50 0.5 1.1 1.7 2.3 2.9 3.5 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 1: 2: 3: 4: 5: –24.828 dB 1.0 GHz –27.749 dB 1.5 GHz –29.57 dB 2.0 GHz –29.588 dB 2.5 GHz –27.86 dB 3.0 GHz –25.098 dB 1.0 GHz –27.928 dB 1.5 GHz 30 20 10 0 –10 –20 –30 –40 –50 0.5 1.1 1 30 20 10 0 –10 –20 –30 –40 1 –28.894 dB 2.0 GHz –28.293 dB 2.5 GHz –26.879 dB 3.0 GHz 2 3 4 5 2 3 4 5 1.7 2.3 2.9 3.5 –50 0.5 1.1 1.7 2.3 2.9 3.5 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. Data Sheet PG10578EJ02V0DS 7 µPG2158T5K INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) 1: 2: 3: 4: 5: –24.907 dB 1.0 GHz –27.235 dB 1.5 GHz –27.784 dB 2.0 GHz –26.52 dB 2.5 GHz –24.38 dB 3.0 GHz –25.825 dB 1.0 GHz 40 30 20 10 0 –10 –20 –30 –40 –50 0.5 1.1 1.7 1 2 3 4 40 30 20 10 0 –10 –20 –30 –40 –50 0.5 1.1 2 1.7 3 2.3 1 4 –28.812 dB 1.5 GHz –28.916 dB 2.0 GHz –26.585 dB 2.5 GHz –23.762 dB 3.0 GHz 5 5 2.3 2.9 3.5 2.9 3.5 Frequency f (GHz) Frequency f (GHz) OUTPUT POWER vs. INPUT POWER +35 f = 2.0 GHz Output Power Pout (dBm) +30 +25 +20 +15 +10 +5 +8 +12 +16 +20 +24 +28 +32 +36 Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. 8 Data Sheet PG10578EJ02V0DS µPG2158T5K PACKAGE DIMENSIONS 6-PIN PLASTIC TSSON (UNIT: mm) (Top View) 1.0±0.1 1.0±0.1 (Bottom View) 1.0±0.1 0.15+0.07 –0.05 0.15+0.07 –0.05 0.35±0.06 0.35±0.06 0.45 ±0.1 1.0±0.1 0.13±0.07 0.23±0.07 0.175±0.075 0.37+0.03 –0.05 Data Sheet PG10578EJ02V0DS 9 µPG2158T5K RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 260°C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260 For soldering Preheating temperature (package surface temperature) : 120°C or below Caution Do not use different soldering methods together (except for partial heating). 10 Data Sheet PG10578EJ02V0DS 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.