UPG2311T5F-E2-A

GaAs INTEGRATED CIRCUIT UPG2311T5F GaAs MMIC LOW NOISE AMPLIFIER FOR GPS DESCRIPTION The µPG2311T5F is a GaAs MMIC LNA for Car Navigation Systems and Handy GPS. This IC consists of two stage amplifiers and has high gain performance. FEATURES • High gain • Low noise : GP = 37 dB TYP. : NF = 1.2 dB TYP. • 12-pin plastic QFN package (3.0 × 3.0 × 0.75 mm) APPLICATION • Car Navigation System • Handy GPS ORDERING INFORMATION (Pb-Free) Part Number Order Number Package 12-pin plastic QFN (Pb-Free) Marking 2311 Supplying Form • Embossed tape 8 mm wide • Pin 1 indicates roll-in direction of tape • Qty 3 kpcs/reel µPG2311T5F-E2-A µPG2311T5F-E2-A Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPG2311T5F-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. Document No. PG10571EJ02V0DS (2nd edition) Date Published July 2005 CP(K) The mark shows major revised points. UPG2311T5F PIN CONNECTIONS Pin No. 1 Pin Name OUT2 GND VCC2 VCC1 GND IN1 GND OUT1 GND IN2 GND GND GND (Top View) 9 8 7 (Bottom View) 7 8 9 2 3 4 5 10 11 12 6 5 6 5 4 10 11 12 6 7 8 9 10 2311 1 2 3 4 3 2 1 11 12 EXPOSED PAD ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherw ise specified) Parameter Supply Voltage Input Power Total Power Dissipation Operating Ambient Temperature Storage Temperature Symbol VCC1, VCC2 Pin Ptot TA Tstg Ratings + 5. 0 −25 0.25 Note Unit V dBm W °C °C −45 to +85 −55 to +150 Note Mounted on double-sided copper-clad 50 × 50 × 1.6 mm epoxy glass PWB, TA = +85°C RECOMMENDED OPERATING RANGE Parameter Operating Frequency Supply Voltage Symbol fopt VCC1, VCC2 MIN. − +2.7 TYP. 1.575 +3.0 MAX. − +3.3 Unit GHz V 2 Data Sheet PG10571EJ02V0DS UPG2311T5F ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC1 = VCC2 = +3.0 V, ZO = 50 Ω, unless otherw ise specified) Parameter Power Gain Note 1 Note 2 Symbol GP NF RLin RLout PO (1 dB) Test Conditions f = 1.575 GHz f = 1.575 GHz f = 1.575 GHz f = 1.575 GHz f = 1.575 GHz MIN. 34 − − − − − TYP. 37 1.2 5 20 +5 MAX. − 1.5 − − − Unit dB dB dB dB dBm Noise Figure Input Return Loss Output Return Loss 1 dB Gain Compression Output Power Circuit Current Note 3 ICC f = 1.575 GHz, Non-RF 17 20 mA Notes 1. Total gain of 1st stage and 2nd stage amplifiers (not include filter loss). 2. NF of 1st stage amplifier. 3. Please refer to following chart. CIRCUIT CURRENT vs. SUPPLY VOLTAGE 25 Circuit Current ICC (mA) 20 15 10 5 0 2.5 2.6 2.7 2.8 2.9 3 SN1 SN2 SN3 3.1 3.2 3.3 3.4 Supply Voltage VCC (V) Remark The graph indicates nominal characteristics. Data Sheet PG10571EJ02V0DS 3 UPG2311T5F TEST CIRCUIT C1 1 µF IN1 C3 1 µF L3 39 nH VCC2 BPF GND OUT1 GND OUT2 GND L2 5.6 nH C2 1 pF C4 1 µF GND L4 3.9 nH VCC1 L1 3.9 nH IN2 GND GND The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. 4 Data Sheet PG10571EJ02V0DS UPG2311T5F ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD IN2 OUT1 L1 OUT2 C2 L2 L3 VCC2 C3 C4 L4 C1 uPG2311T5F IN1 VCC1 USING THE NEC EVALUATION BOARD Symbol C1 C2 C3 C4 Rating 1 µF 1 pF 1 µF 1 µF Size 1608 1005 1608 1608 Symbol L1 L2 L3 L4 Rating 3.9 nH 5.6 nH 39 nH 3.9 nH Size 1005 1005 1005 1005 Data Sheet PG10571EJ02V0DS 5 UPG2311T5F PACKAGE DIMENSIONS 12-PIN PLASTIC QFN (UNIT: mm) 3.0±0.1 0.75±0.1 3.0±0.1 (Bottom View) 1.0 0.4±0.1 0.5±0.06 0.5±0.06 0.9 0.4 1.55±0.1 1.0 0.24+0.07 –0.05 0.4±0.1 Dimensions of pin No.1 indication 0.4±0.1 1.55±0.1 0.4±0.1 6 Data Sheet PG10571EJ02V0DS 0.9 0.4 UPG2311T5F RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 260°C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260 For soldering Preheating temperature (package surface temperature) : 120°C or below Caution Do not use different soldering methods together (except for partial heating). Data Sheet PG10571EJ02V0DS 7 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.