UPG2415TK

GaAs INTEGRATED CIRCUIT PG2415TK 0.5 to 6.0 GHz SPDT SWITCH DESCRIPTION The PG2415TK is a GaAs MMIC SPDT (Single Pole Double Throw) switch for 0.5 to 6.0 GHz applications, including dual-band wireless LAN. This device operates with dual control switching voltages of 2.7 to 5.3 V. This device can operate at frequencies from 0.5 to 6.0 GHz, with low insertion loss and high isolation. This device is housed in a 6-pin lead-less minimold package (1511 PKG) and is suitable for high-density surface m ounting. FEATURES • Switch control voltage • Low insertion loss • High isolation • Handling power : Vcont (H) = 3.0 V TYP. : Vcont (L) = 0 V TYP. : Lins = 0.45 dB TYP. @ f = 2.5 GHz : Lins = 0.65 dB TYP. @ f = 6.0 GHz : ISL = 28 dB TYP. @ f = 2.5 GHz : ISL = 26 dB TYP. @ f = 6.0 GHz : Pin (0.1 dB) = +31.0 dBm TYP. @ f = 2.0 to 6.0 GHz • High-density surface mounting : 6-pin lead-less m inimold package (1.5  1.1  0.55 mm ) APPLICATIONS • Dual-band wireless LAN etc. ORDERING INFORMATION Part Number Order Number Package 6-pin lead-less minimold (1511 PKG) (Pb-Free) Marking G6D Supplying Form  Embossed tape 8 mm wide  Pin 1, 6 face the perforation side of the tape  Qty 5 kpcs/reel PG2415TK-E2 PG2415TK-E2-A Remark To order evaluation samples, please contact your nearby sales office. Part number for sample order: PG2415TK-A Caution Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions must be employed at all times. Document No. PG10793EJ01V0DS (1st edition) Date Published February 2010 NS PG2415TK PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM Pin No. 1 2 3 4 5 6 Pin Name RF1 GND RF2 Vcont2 RFC Vcont1 SW T RUTH TABLE ON Path RFC-RF1 RFC-RF2 Vcont1 High Low Vcont2 Low High ABSOLUTE MAXIMUM RATINGS (T A = +25C, unless otherwise specified) Parameter Switch Control Voltage Input Power (Vcont (H) = 3.0 V) Input Power (Vcont (H) = 5.0 V) Power Dissipation (average) Operating Ambient Temperature Storage Temperature Symbol Vcont Pin Pin PD TA Tstg Ratings +6.0 Note Unit V dBm dBm W C C +34.0 +35.0 0.15 45 to +85 55 to +150 Note Vcont1  Vcont2  6.0 V RECOMMENDED OPERATING RANGE (T A = +25C, unless otherwise specified) Parameter Operating Frequency Switch Control Voltage (H) Switch Control Voltage (L) Control Voltage Difference Symbol f Vcont (H) Vcont (L) MIN. 0.5 2.7 0.2 0.1 TYP.  3.0 0 0 MAX. 6.0 5.3 0.2 0.1 Unit GHz V V V Vcont (H), Vcont (L)Note Note Vcont (H) = Vcont1 (H)  Vcont2 (H) Vcont (L) = Vcont1 (L)  Vcont2 (L) 2 Data Sheet PG10793EJ01V0DS PG2415TK ELECTRICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50  , DC blocking capacitors = 8 pF, unless otherwise specified) Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Return Loss 1 Return Loss 2 Return Loss 3 0.1 dB Loss Compression Input Power Note 2 Symbol Lins1 Lins2 Lins3 Lins4 ISL1 ISL2 ISL3 ISL4 RL1 RL2 RL3 Pin (0.1 dB) Test Conditions f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.8 GHz f = 3.8 to 6.0 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.8 GHz f = 3.8 to 6.0 GHz f = 0.5 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 6.0 GHz f = 0.5 to 2.0 GHz f = 2.0 to 6.0 GHz f = 0.5 to 6.0 GHz Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 MIN.     25 25 25 22 15 15 10   TYP. 0.40 0.45 0.55 0.65 28 28 28 26 20 20 15 +32.0 +31.0 +35.0 +34.0 +34.0 +60 80 80 0.1 50 MAX. 0.65 0.70 0.80 0.90                10 250 Unit dB dB dB dB dB dB dB dB dB dB dB dBm dBm dBm dBm dBm dBm dBc dBc , Vcont (H) = 5.0 V         1 dB Loss Compression Input Power Note 3 Pin (1 dB) f = 0.5 to 2.0 GHz f = 2.0 to 6.0 GHz Input 3rd Order Intercept Point 2nd Harmonics 3rd Harmonics Switch Control Current Switch Control Speed IIP3 2f0 3f0 Icont tSW f = 2.5 GHz, Pin = +20 dBm f = 2.5 GHz, Pin = +20 dBm f = 2.5 GHz, Pin = +20 dBm No RF input 50% CTL to 90/10% RF A ns Notes 1. DC blocking capacitors = 56 pF at f = 0.5 to 2.0 GHz 2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB m ore than that of the linear range. 3. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB m ore than that of the linear range. Caution It is necessary to use DC blocking capacitors with this de vice. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system. Data Sheet PG10793EJ01V0DS 3 PG2415TK EVALUATION CIRCUIT Note C1 : 0.5 to 2.0 GHz : 2.0 to 6.0 GHz C2 : 1 000 pF 56 pF 8 pF The application circuits and their parameters are for reference only and are not intended for use in actual design -ins APPLICATION INFORMATION • LESD provides a means to increase the ESD protection on a specific RF por t, typically the port attached to the antenna. • The value may be tailored to provide specific electrical responses. • The RF ground connections should be kept as short as possible and connected to directly to a good RF ground for best performance. 4 Data Sheet PG10793EJ01V0DS PG2415TK ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD USING THE EVALUATION BOARD Symbol C1 Test Conditions f = 0.5 to 2.0 GHz f = 2.0 to 6.0 GHz C2 Values 56 pF 8 pF 1 000 pF Data Sheet PG10793EJ01V0DS 5 PG2415TK T YPICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50  , DC blocking capacitors = 8 pF, unless otherwise specified) Remark The graphs indicate nominal characteristics. 6 Data Sheet PG10793EJ01V0DS PG2415TK Remark The graphs indicate nominal characteristics. Data Sheet PG10793EJ01V0DS 7 PG2415TK MOUNTING PAD LAYOUT DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm) Remark The mounting pad layout in this document is for reference only. 8 Data Sheet PG10793EJ01V0DS PG2415TK PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm) Data Sheet PG10793EJ01V0DS 9 PG2415TK RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. m ethods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220C or higher Preheating time at 120 to 180C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) W ave Soldering Peak temperature (molten solder temperature) Time at peak temperature Preheating temperature (package surface temperature) Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260C or below : 10 seconds or less : 60 seconds or less : 12030 seconds : 3 times : 0.2%(Wt.) or below : 260C or below : 10 seconds or less : 120C or below : 1 time : 0.2%(Wt.) or below : 350C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 W S260 Condition Symbol IR260 For soldering Caution Do not use different soldering methods together (except for partial heating). 10 Data Sheet PG10793EJ01V0DS PG2415TK Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as rec ommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. Data Sheet PG10793EJ01V0DS 11