CP103N

CP103 Dual OP Amp And Voltage Reference General Description The CP103 is a monolithic IC specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies. The device contains two Op Amps and a 2.5V precision shunt voltage reference. Op Amp 1 is designed for voltage control with its non-inverting input internally connects to the output of the shunt regulator. Op Amp 2 is for current control with both inputs uncommitted. The IC offers the power converter designer a control solution that features increased precision with a corresponding reduction in system complexity and cost. The CP103 is available in standard packages of DIP8 and SOP-8. Features Op Amp · Input Offset Voltage: 0.5mV · Supply Current: 75µA per Op Amp at 5.0V Supply Voltage · Unity Gain Bandwidth: 1MHz · Output Voltage Swing: 0 to (VCC - 1.5) V · Power Supply Range: 3 to 36V Voltage Reference · Fixed Output Voltage Reference: 2.5V · Voltage Tolerance: ± 0.5%, ± 1% · Sink Current Capability from 0.05 to 80mA · Typical Output Impedance: 0.2Ω Applications · · Battery Charger Switching Power Supply SOP-8 DIP-8 Figure 1. Package Types of CP103 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 1 of 9 Rev 1.1 Oct. 28,2004 Fax:886-3-3521052 CP103 Dual OP Amp And Voltage Reference Pin Configuration M Package/P Package (SOP-8/DIP-8) OUTPUT 1 INPUT 1INPUT 1+ / VKA GND 1 2 3 4 8 7 6 5 Top View Figure 2. Pin Configuration of CP103 VCC OUTPUT 2 INPUT 2INPUT 2+ Functional Block Diagram OUTPUT 1 1 Op Amp 1 8 VCC OUTPUT 2 INPUT 2INPUT 2+ INPUT 1INPUT 1+ / VKA GND 2 - + + 7 3 - Vref Op Amp 2 6 4 5 Figure 3. Functional Block Diagram of CP103 * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 2 of 9 Rev 1.1 Oct. 28,2004 Fax:886-3-3521052 CP103 Dual OP Amp And Voltage Reference Ordering Information CP103 X X Blank: SOP-8, Tube A: SOP-8, Taping N: DIP-8, Tube Blank: V REF±1% G: VREF±0.5% Absolute Maximum Ratings (Note 1) Parameter Power Supply Voltage (VCC to GND) Op Amp 1 and 2 Input Voltage Range (Pins 2, 5, 6) Op Amp 2 Input Differential Voltage (Pins 5, 6) Voltage Reference Cathode Current (Pin 3) Power Dissipation Symbol VCC VIN VID IK PD TSTG DIP-8 SOP-8 Storage Temperature Range ESD Protection Voltage (Human Body Model) Value 40 - 0.3 to VCC + 0.3 40 30 800 500 -65 to 150 ≥ 2000 o Unit V V V mA mW C V Note 1: Stresses greater than those listed under "Absolute Maximum Ratings " may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings " for extended periods may affect device reliability. Recommended Operating Conditions Parameter Supply Voltage Ambient Temperature Min 3 -40 Max 36 105 Unit V o C * All specs and applications shown above subject to change without prior notice. 1F-5 NO.66 SEC.2 NAN-KAN RD ., LUCHU , TAOYUAN, TAIWAN Email: server@ceramate.com.tw Tel:886-3-3214525 Http: www.ceramate.com.tw Page 3 of 9 Rev 1.1 Oct. 28,2004 Fax:886-3-3521052 CP103 Dual OP Amp And Voltage Reference Electrical Characteristics Operating Conditions: VCC = +5V, TA= 25oC unless otherwise specified. Parameter Conditions Min Typ 0.15 0.20 Max 0.25 0.30 Unit mA Total Supply Current, excluding Cur- V = 5V, no load, -40oC ≤T ≤105oC CC A rent in Voltage Reference o VCC = 30V, no load, -40 C ≤TA ≤105oC Voltage Reference Section CP103G Reference Voltage CP103 IK = 10mA TA = 25oC -40oC ≤TA ≤105oC TA = 25oC -40oC ≤TA ≤105oC Reference Voltage Deviation Over Full Temperature Range Minimum Cathode Current for Regulation Dynamic Impedance IK = 1.0 to 80mA, f