APS-100ESS271MHB5S

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead @Super low ESR, high temperature resistance @Large capacitance & Improved high ripple current capability @Rated voltage range : 2.5 to 25Vdc @2000 hours at 105C @Suitable for DC-DC converters, voltage regulators and decoupling applications For computer motherboards @Pb-free design ?SPECIFICATIONS Items Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note Dissipation Factor (tane) Low Temperature Characteristics Endurance -55 to +105C 2.5 to 25Vdc P20% (M) Rated voltageB1.15V I=0.2CV (max.) Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc) 0.12 max. (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) Characteristics Bias Humidity Test Surge Voltage Test Failure Rate (at 20C, 120Hz) Max. impedance ratio at 100kHz to the 20C value Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C, 90 to 95% RH for 500 hours. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 1% per 1000 hours maximum (Confidence level 60% at 105C) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] @Terminal Code : E F0.6 Coated Case FD+0.5max. FP0.5 ?MARKING EX) 4V820MF PS18M 820 4V fD L F 8 11.5 3.5 10 12.5 5.0 L+1.5 max. 15min. 4min. (1/2) CAT. No. E1001E CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead ?PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PS- AAA E AA AAA M AAA S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 270MF:271,1500MF:152) Lead forming·Taping code Terminal code Voltage code (ex. 4V:4R0,6.3V:6R3,10V:100) Series code Category Please refer to "A guide to global code (conductive polymer type)" ?STANDARD RATINGS WV(Vdc) Cap(µF) 680 1500 560 820 390 680 270 470 180 330 100 150 68 100 Case size fDbL(mm) 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 ESR (momax/20c, 100k to 300kHz) 10 8 10 8 12 10 14 12 16 14 24 20 24 20 Rated ripple current (mArms/105c, 100kHz) 5230 5500 5230 5500 4770 5500 4420 5300 4360 5050 3320 4320 3320 4320 Part No. APS-2R5ESS681MHB5S APS-2R5ESS152MJC5S APS-4R0ESS561MHB5S APS-4R0ESS821MJC5S APS-6R3ESS391MHB5S APS-6R3ESS681MJC5S APS-100ESS271MHB5S APS-100ESS471MJC5S APS-160ESS181MHB5S APS-160ESS331MJC5S APS-200ESS101MHB5S APS-200ESS151MJC5S APS-250ESS680MHB5S APS-250ESS101MJC5S 2.5 4 6.3 10 16 20 25 SS : Lead forming code and taping code (2/2) CAT. No. E1001E