5KP51

5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR CHENG- YI CHENGELECTRONIC VOLTAGE 5.0 to 110 VOLTS 5000 WATT PEAK PULSE POWER P600 FEATURES Plastic package has Underwrites Laboratory Flammability Classification 94V-O Glass passivated junction 5000W Peak Pulse Power capability on 10/1000 s waveform Excellent clamping capability Repetition rate (Duty Cycle):0.5% Low incremental surge resistance Fast response time: typically less than 1.0 ps from 0 volts to BV Typical ID less than 1 A above 10V High temperature soldering guaranteed: 300oC/10 seconds /.375',(9.5mm) lead length/51bs.,(2.3kg) tension MECHANICAL DATA Case:Molded plastic over glass passivated junction Terminals:Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity:Color band denote positive end (cathode) Mounting Position:Any Weight:0.07 ounces, 2.1gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. RATINGS Peak Pulse Power Dissipation on 10/1000 Peak Pulse Current of on 10/1000 Steady Power Dissipation at TL=75 C Lead Lengths .375",(9.5mm)(NOTE 2) Peak Forward Surge Current 8.3ms Single Half Sine-Wave Superimposed on Rated Load(JEDEC Method)(NOTE 3) Operating Junction and Storage Temperature Range 0 SYMBOL s waveform (NOTE 1,Fig.1) PPPM PPPM PM(AV) s waveform (NOTE 1,Fig.3) VALUE Minimum 5000 SEE TABLE 1 8.0 UNITS Watts Amps Watts Amps 0 IFSM TJ, TSTG 400 -55 to + 175 C Notes: 1. Non-repetitive current pulse, per Fig.3 and derated above TA=25oC per Fig.2 2. Mounted on Copper Leaf area of 0.79 in2 (20mm2) 3. Measured on 8.3ms single half sine-wave or equivalent square wave, Duty Cycle=4 pulses per minuters maximum. 5KP SERIES GLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES 5KP SERIES Fig. 1 - PEAK PULSE POWER VS PULSE TIME PEAK PULSE POWER (P PP) OR CURRENT (l PP) DERATING PERCENTAGE % 100 Fig. 2 - PULSE DERATING CURVE PPPM, PEAK PULSE POWER, kW 100 Non-Repetitive Pulse waveform Shown in Flgure 3 TA=250C 75 10 50 1.0 25 0.1 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0 0 25 50 75 100 125 150 175 200 td, PULSE WIDTH, SEC TA, AMBIENT TEMPERATURE, 0C Fig. 3 - PULSE WAVEFORM 150 Fig. 4 - TYPICAL JUNCTION CAPACIT ANCE UNIDIRECTIONAL 104 0 TJ=25C f=1.0MHz Vsig=50mVp-p IPPM, PEAK PULSE CURRENT, % tf=10 se Peak Value Ippm TA=250C Pulse Width (td) is Defined as the Poitn Where the Peak Current Decays to 50% of Ipp 40,000 20,000 100 Measursd at Zero Bias CJ, CAPACITANCE, pF 10,000 6,000 4,000 2,000 1,000 400 Measursd at Stand-Off Voltage(V MW) Half Value-Ipp 2 50 10/1000 sec Waveform as Defined by R.E.A e-kt td 0 1.0 2.0 3.0 4.0 0 t, TIME, ms 200 Pm (AV) STEADY STATE POWER DISSIPATION, WATTS Fig. 5 - STEADY STATE POWER DERATING CURVE 0.8 100 1.0 2.0 5.0 10 20 50 100 200 V(WM), REVERSE STAND-OFF VOLT AGE, VOLTS Fig. 6 - MAXIMUM NON-REPETITIVE IFSM, PEAK FORWARD SURGE CURRENT AMPERES 0.6 PEAK FORWARD SURGE CURRENT 400 350 300 250 200 150 100 1 2 3 5 10 20 30 50 100 TJ=TJ max 0.4 l=375"(9.5mm) 8.3ms Single Half Sine-Wave JEDEC Method 0.2 20mmx20mmx1mm Cu (0.8"x0.8"x.040") 0 0 25 50 75 100 125 150 175 200 TL, LEAD TEMPERATURE, 0C NUMBER OF CYCLES AT 60 Hz