ER1C

ER1A thru ER1J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI CHENGELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -1.0 Amperes SMB/DO-214AA FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .075(1.91) .083(2.11) .130(3.30) .155(3.94) .160(4.06) .185(4.70) .006(.152) .012(.305) .083(2.13) .096(2.44) .002(.051) .008(.203) .200(5.08) .220(5.59) MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 12mm tape (EIA-481) Weight: 0.003 ounces, 0.093 gram .030(0.76) .050(1.27) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ER1A 50 35 50 ER1B 100 70 100 ER1C 150 105 150 ER1D 200 140 200 1.0 ER1E 300 210 300 ER1G 400 280 400 ER1J 600 420 600 UNITS V V V A Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=100 C 0 VRRM VRMS VDC I(AV) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current at Rated DC Blocking Voltage @ TA=250C @ TA=1000C IFSM VF IR TRR CJ R JL TJ , TSTG 30.0 A 0.95 5.0 100 35.0 10.0 34 -50 to +150 1.25 1.7 V A nS pF 0 Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range C/W 0 C Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. ER1A thru ER1J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ER1A THRU ER1J Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G 50 Noninductive 10 Noninductive Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING AVERAGE FORWARD CURRENT, AMPERES 2.0 SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315x0.315"(8.0x8.0mm) COPPER PAD AREAS trr +0.5A () PULSE GENERATOR NOTE 2 (+) 25 Vdc (approx) () D.U.T. 0 -0.25 1.0 1 NONInductive OSCILLOSCOPE NOTE 1 (+) NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. -1.0 SET TIME BASE FOR 10ns/cm 1cm 25 50 75 100 125 150 175 LEAD TEMPERATURE, oC Fig. 3 - TYPICAL REVERSE CHARACTERISTICS 1000 IR-REVERSE LEAKAGE CURRENT, MICROAMPERES Fig. 4 - TYPICAL FORWARD CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 0 TJ=125C ES1A 1.0 100 TJ=75C 0 ES1J ES1E 0.1 10 1.0 TJ=25C 0 0.01 0 TJ=25C 0.1 20 40 60 80 10 0 120 % of PIV, VOLTS 0.001 0.2 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 5 - MAXIMUM NON-REPETITIVE SURGE CURRENT 30 25 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD Fig. 6 - TYPICAL JUNCTION CAPACITANCE 14 JUNCTION CAPACITANCE, pF 0 TJ=25C f=1.0MHZ Vslg=50mVp-p PEAK FORWARD SURGE CURRENT, AMPERES 12 10 8.0 6.0 4.0 2.0 20 15 10 5 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz 0 0.1 1 10 100 REVERSE VOLTAGE, VOLTS