ER2D

ER2A thru ER2J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI CHENGELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -2.0 Amperes SMB/DO-214AA FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .075(1.91) .083(2.11) .130(3.30) .155(3.94) .160(4.06) .185(4.70) .006(.152) .012(.305) .083(2.13) .096(2.44) .002(.051) .008(.203) .200(5.08) .220(5.59) MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 12mm tape (EIA-481) Weight: 0.003 ounces, 0.093 gram .030(0.76) .050(1.27) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ER2A 50 35 50 ER2B 100 70 100 ER2C 150 105 150 ER2D 200 140 200 2.0 ER2E 300 210 300 ER2G 400 280 400 ER2J 600 420 600 UNITS V V V A Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=110 C 0 VRRM VRMS VDC I(AV) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current at Rated DC Blocking Voltage @ TA=250C @ TA=1000C IFSM VF IR TRR CJ R JL TJ , TSTG 50.0 A 0.95 5.0 150 35.0 25.0 20.0 -50 to +150 1.25 1.7 V A nS pF 0 Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range C/W 0 C Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. ER2A thru ER2J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ER2A THRU ER2J Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G 50 Noninductive 10 Noninductive Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 2.4 2.0 1.6 1.2 0.8 0.4 0 0 20 40 60 80 100 120 140 160 SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.3x0.3"(8.0x8.0mm) COPPER PAD AREAS trr +0.5A () PULSE GENERATOR NOTE 2 (+) 25 Vdc (approx) () D.U.T. 0 -0.25 1 NONInductive OSCILLOSCOPE NOTE 1 (+) NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. -1.0 SET TIME BASE FOR 10ns/cm 1cm LEAD TEMPERATURE, oC Fig. 3 - TYPICAL REVERSE CHARACTERISTICS 1000 Fig. 4 - TYPICAL FORWARD CHARACTERISTICS 50.0 TJ=100C 0 100 INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MICROAMPERES ER2A 10.0 10 TJ=750C ER2E 1.0 ER2J 1.0 TJ=25 C 0 0.1 TJ=25 C 0 0.1 PULSE WIDTH=300 S 2% DUTY CYCLE 0.01 20 40 60 80 100 120 140 PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 5 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 60 60 50 50 40 30 20 10 10 1 2 5 10 20 50 100 0.1 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD Fig. 6 - TYPICAL JUNCTION CAPACITANCE CAPACITANCE, pF 40 30 20 0 TJ=25C f=1.0MHZ Vslg=50mVp-p NUMBER OF CYCLES AT 60Hz 0.5 1 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE, VOLTS