ER3C

ER3A thru ER3J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI CHENGELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -3.0 Amperes SMC/DO-214AB FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .108(2.75) .128(3.25) .220(5.59) .245(6.22) .260(6.60) .280(7.11) .006(.152) .012(.305) .079(2.00) .103(2.62) .002(.051) .008(.203) .305(7.75) .320(8.13) MECHANICAL DATA Case: JEDEC DO-214AB molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 16mm tape (EIA-481) Weight: 0.007 ounces, 0.21 gram .030(0.76) .050(1.27) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ER3A 50 35 50 ER3B 100 70 100 ER3C 150 105 150 ER3D 200 140 200 3.0 ER3E 300 210 300 ER3G 400 280 400 ER3J 600 420 600 UNITS V V V A Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=75 C 0 VRRM VRMS VDC I(AV) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 3.0A Maximum DC Reverse Current at Rated DC Blocking Voltage @ TA=250C @ TA=1000C IFSM VF IR TRR CJ R JL TJ , TSTG 100 A 0.95 5.0 200 35.0 45.0 16 -50 to +150 1.25 1.7 V A nS pF 0 Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range C/W 0 C Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. ER3A thru ER3J SURFACE MOUNT SUPERFAST S URFACE RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ER3A THRU ER3J AVERAGE FORWARD CURRENT, AMPERES Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G 50 Noninductive 10 Noninductive Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING 3.0 2.5 2.0 1.5 1.0 0.5 0 50 60 70 80 90 100 110 120 130 140 150 LEAD TEMPERATURE, oC SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315x0.315"(8.0x8.0mm) COPPER PAD AREAS trr +0.5A () PULSE GENERATOR NOTE 2 (+) 25 Vdc (approx) () D.U.T. 0 -0.25 1 NONInductive OSCILLOSCOPE NOTE 1 (+) NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. -1.0 SET TIME BASE FOR 10ns/cm 1cm Fig. 3 - TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES Fig. 4 - TYPICAL FORWARD CHARACTERISTICS TJ=100 C 0 100 INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 0 TJ=75C ER3A-ER3D 10 ER3A-ER3G ER3J 1.0 TJ=25C 0 1 0.1 0.1 0.01 20 40 60 80 100 120 140 PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS 0 TJ=25C PULSE WIDTH=300 S 2% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 5 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 200 100 90 CAPACITANCE, pF Fig. 6 - TYPICAL JUNCTION CAPACITANCE TJ=25C f=1.0MHZ Vslg=50mVp-p 0 100 75 50 45 30 15 50 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD 10 1 5 10 50 100 0.1 0.5 1 2 5 10 20 50 100 200 500 1000 NUMBER OF CYCLES AT 60Hz REVERSE VOLTAGE, VOLTS