FR2B

FR2A thru FR2K SURFACE MOUNT ULTRAFAST S URFACE RECTIFIER CHENG- YI CHENGELECTRONIC VOLTAGE RANGE -50 TO 800 VOLTS CURRENT -2.0 Amperes SMB/DO-214AA FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Fast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated chip junction High temperature soldering 260oC/10 seconds at terminals .075(1.91) .083(2.11) .130(3.30) .155(3.94) .160(4.06) .185(4.70) .006(.152) .012(.305) .083(2.13) .096(2.44) .002(.051) .008(.203) .200(5.08) .220(5.59) MECHANICAL DATA Case: JEDEC DO-214AA molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 12mm tape (EIA-481) Weight: 0.003 ounces, 0.093 gram .030(0.76) .050(1.27) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS FR2A 50 35 50 FR2B 100 70 100 FR2D 200 140 200 2.0 FR2G 400 280 400 FR2J 600 420 600 FR2K 800 560 800 UNITS V V V A Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at TL=90 C 0 VRRM VRMS VDC I(AV) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current at Rated DC Blocking Voltage @ TA=250C @ TA=1250C 0 IFSM VF IR TRR CJ R JL TJ , TSTG 150 50.0 A 1.30 5.0 200 250 40 V A 500 Maximum Reverse Recovery Time (Note 1) TJ=25 C Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range nS pF 0 20.0 -50 to +150 C/W 0 C Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. FR2A thru FR2K SURFACE MOUNT FAST SWITCHENG S URFACE RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES FR2A THRU FR2K Fig. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES 2.0 1.5 PEAK FORWARD SURGE CURRENT, AMPERES Fig. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 60 50 40 30 20 10 8.3ms Single Half Since-Wave JEDEC Method 1.0 RESISTIVE OR INDUCTIVE LOAD P.C. Board mounted on 8.0mm2 COPPER LAND AREAS 0.5 0 50 60 70 80 90 100 110 1 20 130 140 150 LEAD TEMPERATURE, oC 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz Fig. 3 - FORWARD CHARACTERISTICS 10 Fig. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES 100 1 1FM, Apk TYPICAL 10 TA=125C 0 0.1 0 TJ=25C 1.0 TA=25C 0 0.01 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, % Fig. 5 - TYPICAL JUNCTION CHARACTERISTICS 100 Fig. 6 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM trr +0.5A 50 Noninductive 10 Noninductive CAPACITANCE, pF 50 0 -0.25 () PULSE GENERATOR NOTE 2 10 0 TJ=25C f=1.0MHz Vsig=50mVp-p (+) 25 Vdc (approx) () D.U.T. 5 1 5 10 50 100 REVERSE VOLTAGE, VOLTS 1 NONInductive OSCILLOSCOPE NOTE 1 (+) -1.0 SET TIME BASE FOR 10ns/cm 1cm NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms.