S2J

S2A thru S2M SERIES SURFACE MOUNT RECTIFIER CHENG- YI CHENGELECTRONIC VOLTAGE RANGE 50 TO 1000 Volts CURRENT 2.0 Amperes SMB/DO-214AA FEATURES For surface mounted applications High tempreature metallurgically bonded-no compression contacts as found in other diode-constructed rectifiers Glass passivated junction Built-in strain relief Easy pick and place Plastic package has Underwrites Laboratory Flamability Classification 94V-O Complete device submersible temperature of 2600C for 10 seconds solder bath .075(1.91) .083(2.11) .130(3.30) .155(3.94) .160(4.06) .185(4.70) .006(.152) .012(.305) .083(2.13) .096(2.44) .030(0.76) .050(1.27) .004(.102) .008(.203) MECHANICAL DATA Case:JEDEC DO-214AA molded plastic Terminals:Solder plated solderable per MIL-STD-750, Method 2026 Polarity:Indicated by cathode band Standard Packaging: 12mm tape (EIA STD EIA-481) Weight:0.003 ounce, 0.093 gram .200(5.08) .220(5.59) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Signle phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, at T L =1100C SYMBOL VRRM VRMS VDC I(AV) IFSM VF 0 S2A 50 35 50 S2B 100 70 100 S2D 200 140 200 2.0 60.0 1.10 5.0 200 2.5 30.0 16 S2G 400 280 400 S2J 600 420 600 S2K 800 560 800 S2M 1000 700 1000 UNITS Volts Volts Volts Amps Amps Volts A S pF 0 Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 2.0A Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Maximum Thermal Resistance (Note 3) Operating and Storage Temperature Range R @TA=25 C @TA=1250C IR TRR CJ JL C/W 0 TJ TSTG -50 to +150 C Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, Irr=0.25A 2. Measured at 1 MHz and Applied Vr= 4.0 volts 3. 8.0mm2(0.13mm thick) land areas S2A thru S2M SERIES SURFACE MOUNT RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES S2A THRU S2M Fig.2 - MAXIMUM NON-REPETITIVE PEAK FORWARD Fig.1 - FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD RECTIFIED CURRENT AMPERES 60 50 40 30 20 10 5 1.0 TA = 55oC Single Sine-Wave JEDEC Method SURGE CURRENT 2.4 2.0 1.6 1.2 0.8 0.4 0 0 20 40 60 80 100 120 140 160 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INOUCTIVE LOAD P.C.B MOUNTED ON 0.3x0.3"(8.0x8.0mm) COPPER PAD AREAS 10 CYCLE 10 20 40 60 100 LEAD TEMPERATURE, 0C 2.0 4.0 6.0 NUMBER OF CYCLES AT 60 Hz Fig.3 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (mA) INSTANTANEOUS REVERSE CURRENT MICROAMPERES 100 10 0 TJ=125C Fig.4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 50 20 10 5 2 1 0.5 0.2 0.1 0.05 0.02 0.01 0.4 1 0.1 0.01 0.001 0 20 40 60 80 100 120 140 0 TJ=75C 0 TJ=25C 0.6 0.8 1 1.2 1.4 1.6 1.8 2 INSTANTANEOUS FORWARD VOLT AGE, (V) PERCENT OF PEAK REVERSE VOLTAGE, % Fig.5 - TRANSIENT THERMAL IMPEDANCE THERMAL IMPEDANCE ( 0C/W ) 1,000 500 200 100 50 20 10 5 2 1 0.01 Fig.6 - TYPICAL JUNCTION CAPACIT ANCE 100 CAPACITANCE-pF Units Mounted on 2 20in2(5.4 mm)+0 .5mil inches (0.013mm) Thick Copper Land Areas 50 20 10 5 2 1 0.01 0 TJ=25C f=1.0MHz Vsig=50m Vp-p 0.1 1 10 100 0.1 1 10 100 HEATING TIME (SEC) REVERSE VOLTAGE(V)