CHDTA123YUPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT PNP Digital Silicon Transistor VOLTAGE 50 Volts APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. C HDTA123YUPT CURRENT 100 mAmpere FEATURE * Small surface mounting type. (SC-70/SOT-323) * High current gain. * Suitable for high packing density. * * * * Low colloector-emitter saturation. High saturation current capability. Internal isolated PNP transistors in one package. Built in bias resistor(R1=2.2kΩ, Typ. ) (2) SC-70/SOT-323 (3) 1.3±0.1 0.3±0.1 0.65 2.0±0.2 0.65 (1) CONSTRUCTION * One PNP transistors and bias of thin-film resistors in one package. 1.25±0.1 MARKING YU1 Gnd In 1 0.05~0.2 0.1Min. 2.0~2.45 0.8~1.1 0~0.1 CIRCUIT 2 R2 TR R1 3 Out Dimensions in millimeters SC-70/SOT-323 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VCC VIN IO DC Output current IC(Max.) PTOT TSTG TJ RθJ-S Note 1. Transistor mounted on an FR4 printed-circuit board. 2005-06 PARAMETER Supply voltage Input voltage CONDITIONS − MIN. MAX. -50 +5 -100 V V UNIT -12 − − Tamb ≤ 25 OC, Note 1 − −55 − junction - soldering point − mA -100 200 +150 150 140 mW O Total power dissipation Storage temperature Junction temperature Thermal resistance C C C/W O O RATING CHARACTERISTIC ( CHDTA123YUPT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL VIoff) VI(on) VO(on) II IC(off) hFE R1 R2/R1 fT PARAMETER Input off voltage Input on voltage Output voltage Input current Output current DC current gain Input resistor Resistor ratio Transition frequency IC=-5mA, VCE=-10.0V f=100MHz = CONDITIONS IO=-100uA; VCC=-5.0V IO=-20mA; VO=-0.3V IO=-10mA; II=-0.5mA VI=-5V VI=0V; VCC=-50V IO=-10mA; VO=-5.0V − − − − 33 1.54 3.6 − MIN. -0.3 − − − − − − 2.2 4.5 250 TYP. − -3.0 -0.3 -3.8 -0.5 − 2.86 5.5 − KΩ MHz MAX. V V V mA uA UNIT Note 1.Pulse test: tp≤300uS; δ≤0.02. RATING CHARACTERISTIC CURVES ( CHDTA123YUPT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) -100 -50 Fig.2 Output current vs. input voltage (OFF characteristics) -10m -5m Vo = -0.3V OUTPUT CURRENT : Io (A) VCC= −5V INPUT VOLTAGE : VI(on) (V) -2m -1m -500u -200u -100u -50u -20u -10u -5u -20 -10 -5 -2 -1 -500m Ta=-40OC 25OC 100OC Ta=100OC 25OC -40 OC -200m -100m -100u -2u -1u -1m -10m -100m 0 -0.4 -1.0 -1.4 -2.0 -2.4 -3.0 OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI(off) (V) Fig.3 DC current gain vs. output current 1k 500 -1 Fig.4 Output voltage vs. output current lO/lI=20 Ta=100 C 25OC -40 OC O VO =- 5V -500m DC CURRENT GAIN : GI 200 100 50 20 10 5 Ta=100OC 25OC -40OC OUTPUT VOLTAGE : VO(on) (V) -200m -100m -50m -20m -10m -5m 2 1 -100u -2m -1m -100u -1m -10m -100m -1m -10m -100m OUTPUT CURRENT : IO (A) OUTPUT CURRENT : IO (A)