CHDTD123EKPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT NPN Digital Silicon Transistor VOLTAGE 50 Volts APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. C HDTD123EKPT CURRENT 500 mAmpere FEATURE * Small surface mounting type. (SC-59/SOT-346) * High current gain. * Suitable for high packing density. * * * * Low colloector-emitter saturation. High saturation current capability. Internal isolated NPN transistors in one package. Built in bias resistor(R1=4.7kΩ, Typ. ) SC-59/SOT-346 (2) (3) 0.95 2.7~3.1 0.95 (1) 1.7~2.1 CONSTRUCTION * One NPN transistors and bias of thin-film resistors in one package. 0.3~0.51 1.2~1.9 MARKING EKI 0.085~0.2 Gnd In 1 0.89~1.3 0.3~0.6 2.1~2.95 0~0.1 CIRCUIT 2 R2 TR R1 3 Out Dimensions in millimeters SC-59/SOT-346 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VCC VIN IC PTOT TSTG TJ RθJ-S Note 1. Transistor mounted on an FR4 printed-circuit board. 2004-01 PARAMETER Supply voltage Input voltage DC Output current Total power dissipation Storage temperature Junction temperature Thermal resistance CONDITIONS − MIN. MAX. 50 +30 500 200 +150 150 150 V V UNIT -10 − Tamb ≤ 25 OC, Note 1 − −55 − junction - soldering point − mA mW O C C C/W O O RATING CHARACTERISTIC ( CHDTD123EKPT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL VIoff) VI(on) VO(on) II IO(off) hFE R1 R2/R1 fT PARAMETER Input off voltage Input on voltage Output voltage Input current Output current DC current gain Input resistor Resistor ratio Transition frequency IE=-5mA, VCE=10.0V f=100MHz = CONDITIONS IO=100uA; VCC=5.0V IO=20mA; VO=0.3V IO=50mA; II=2.5mA VI=5V VI=0V; VCC=50V IO=50mA; VO=5.0V − − − − 47 3.29 0.8 − MIN. 0.5 − − 0.1 − − − 4.7 1.0 200 TYP. − 3.0 0.3 1.8 0.5 − 6.11 1.2 − KΩ MHz MAX. V V V mA uA UNIT Note 1.Pulse test: tp≤300uS; δ≤0.02. RATING CHARACTERISTIC CURVES ( CHDTD123EKPT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) 100 50 VO= 0.3V Fig.2 Output current vs. input voltage (OFF characteristics) 10m VCC= 5V INPUT VOLTAGE : VI(on) (V) OUTPUT CURRENT : Io (A) 20 10 5 2 1 500m 200m 100m 500u 1m 10m 100m 500m Ta =- 40OC 25OC = 100OC 1m Ta=100OC 25OC -40 OC 100u 10u 1u 0 1.0 2.0 INPUT VOLTAGE : VI(off) (V) 3.0 OUTPUT CURRENT : IO (A) 1k Fig.3 DC current gain vs. output current VO =5V Ta=100OC 25OC -40OC OUTPUT VOLTAGE : VO(on) (V) Fig.4 Output voltage vs. output current 1 500m 200m 100m 50m 20m 10m 5m 2m Ta=100OC 25OC -40 OC lO/lI=20 500 DC CURRENT GAIN : GI 200 100 50 20 10 5 2 1 100 200 500 1m 2m 5m 10m 20m 50m100m 1m 500u 1m 10m 100m 500m OUTPUT CURRENT : IO (A) OUTPUT CURRENT : IO (A)