CHUMA2PT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT Dual Digital Silicon Transistor VOLTAGE 50 Volts APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. CHUMA2PT CURRENT 30 mAmpere FEATURE * Small surface mounting type. (SC-88A/SOT-353) * High current gain. * Suitable for high packing density. * * * * Low colloector-emitter saturation. High saturation current capability. tow CHDTA144E chips in apackage. Built in bias resistor(R1=47kΩ, Typ. ) (1) (5) SC-88A/SOT353 1.2~1.4 (2) (3) 0.65 0.65 2.0~2.5 0.15~0.35 1.15~1.35 0.08~0.15 0.1 Min. 0.8~1.1 0~0.1 2.15~2.45 CIRCUIT 3 R1 R2 2 R1 R2 1 4 5 Dimensions in millimeters SC-88A/SOT353 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VCC VIN IO DC Output current IC(Max.) PTOT TSTG TJ Note 1. Transistor mounted on an FR4 printed-circuit board. 2004-04 PARAMETER Supply voltage Input voltage CONDITIONS − MIN. MAX. -50 +10 -30 V V UNIT -40 − − Tamb ≤ 25 OC, Note 1 − −55 − mA -100 150 +150 150 mW O Total power dissipation Storage temperature Junction temperature C C O RATING CHARACTERISTIC ( CHUMA2PT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL VIoff) VI(on) VO(on) II IC(off) hFE R1 R2/R1 fT PARAMETER Input off voltage Input on voltage Output voltage Input current Output current DC current gain Input resistor Resistor ratio Transition frequency IC=-5mA, VCE=-10.0V f =100MHz CONDITIONS IO=-100uA; VCC=-5.0V IO=-2mA; VO=-0.3V IO=-10mA; II=-0.5mA VI=-5V VI=0V; VCC=-50V IO=-5mA; VO=-5.0V − − − − 68 32.9 0.8 − MIN. -0.5 − − -0.1 − − − 47 1.0 250 TYP. MAX. − -3.0 -0.3 -0.18 -0.5 − 61.1 1.2 − KΩ MHz V V V mA uA UNIT Note 1.Pulse test: tp≤300uS; δ≤0.02. RATING CHARACTERISTIC CURVES ( CHUMA2PT ) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) -100 -50 VO=- 0.3V Fig.2 Output current vs. input voltage (OFF characteristics) -10m VCC =- 5V -5m OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) -2m -1m -500 -200 -100 -50 -20 -10 -5 -2 -1 -0 -20 -10 -5 -2 -1 -500m -200m -100m -100 -200 -500 -1m -2m -5m -10m -20m -50m -100m Ta =- 40OC 25OC = 100OC Ta=100OC 25OC -40 OC -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI(off) (V) Fig.3 DC current gain vs. output current 1k 500 DC CURRENT GAIN : GI Fig.4 Output voltage vs. output current -1 -500m OUTPUT VOLTAGE : VO(on) (V) VO =- 5V Ta=100OC 25OC -40OC lO/lI=20 Ta=100 C 25OC -40 OC O 200 100 50 20 10 5 2 -200m -100m -50m -20m -10m -5m -2m 1 -100 -200 -500 -1m -2m -5m -10m -20m -50m -100m -1m -100 -200 -500 -1m -2m -5m -10m -20m -50m -100m OUTPUT CURRENT : IO (A) OUTPUT CURRENT : IO (A)