HER102PT

CHENMKO ENTERPRISE CO.,LTD HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 - 1000 Volts FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low power loss, high efficiency * Low leakage * High current capability * High speed switching * High current surge * High reliability * High temperature soldering guaranteed : 260oC/10 seconds at terminals H ER101PT THRU HER108PT CURRENT 1.0 Ampere DO-41 0.034(0.9) DIA. 0.028(0.7) 1.0(25.4) MIN. MECHANICAL DATA Case: JEDEC DO-41 molded plastic Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Weight: 0.35 gram 0.205(5.2) 0.166(4.2) 0.107(2.7) DIA. 0.080(2.0) 1.0(25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) DO-41 UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TA = 50 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30 Amps o SYMBOL VRRM VRMS VDC IO HER101PT HER102PT HER103PTHER104PT HER105PT HER106PT HER107PT HER108PT 50 35 50 100 70 100 200 140 200 300 210 300 1.0 400 280 400 600 420 600 800 560 800 1000 700 1000 Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 15 -65 to +150 12 pF o C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC Maximum Full Load Reverse Current Average, Full Cycle 0.375" (9.5mm) lead length at TL = 55oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A SYMBOL VF HER101PT HER102PT HER103PTHER104PTHER105PT HER106PT HER107PT HER108PT UNITS Volts uAmps uAmps 1.0 1.3 5.0 1.50 1.70 IR 100 trr 50 70 nSec 2001-6 RATING CHARACTERISTIC CURVES ( HER101PT THRU HER108PT ) 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 1.0 1 NONINDUCTIVE 0.5 OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ= 150oC HER101PT~HER103PT 10 TJ= 100oC 1.0 HER104PT~HER105PT 1.0 TJ= 25oC 0.1 HER106PT .1 0.01 TJ= 25oC HER107PT~HER108PT Pulse Width = 300uS 1% Duty Cycle 0.001 0 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 35 JUNCTION CAPACITANCE, ( pF ) 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 200 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 6 - TYPICAL JUNCTION CAPACITANCE TJ= 25oC 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 HER1 01PT ~105P T 8.3ms Single Half Sine-Wave (JEDEC Method) HER1 06PT ~108 PT