HMB11PT

CHENMKO ENTERPRISE CO.,LTD MINIATURE GLASS PASSIVATED S INGLE-PHASE SURFACE MOUNT BRIDGE RECTIFIER VOLTAGE RANGE 50 - 200 Volts CURRENT 0.5 Ampere FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Surge overload rating of 35 Amperes peak * Glass passivated chip junction * Ideal for printed circuit board * High temperature soldering guaranteed : 260oC/10 seconds at terminals H MB11PT THRU HMB13PT MD-S 0.049(1.24) 0.039(0.99) 0.179(4.55) 0.272(6.90) 0.252(6.40) 0.161(4.10) 0.144(3.65) 0.195(4.95) 0.062(1.57) 0.058(1.47) 0.038(0.96) 0.019(0.48) 0.058(1.47) 0.054(1.37) 0.105(2.67) 0.095(2.41) 0.117(2.97) 0.107(2.72) MECHANICAL DATA Case: JEDEC MD-S molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Polarity syHMBols marked on body Weight: 0.008 ounces, 0.22 gram 0.008(0.20) 0.004(0.10) 0.029(0.74) 0.017(0.43) 0.114(2.90) 0.094(2.40) 0.106(2.70) 0.090(2.30) 0.0075(0.19) 0.0065(0.16) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC aHMBient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MD-S HMB13PT 200 140 200 UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TA = 30oC On glass-epoxy P.C.B.(NOTE 1) On aluminum substrate (NOTE 2) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Reverse Recovery Time Typical Junction Capacitance (Note 3) Typical thermal resistance per leg Operating and Storage Temperature Range SYHMBOL VRRM VRMS VDC IO HMB11PT 50 35 50 HMB12PT 100 70 100 0.5 IFSM TRR CJ R JA 30 50 10 85 -55 to +150 TJ, TSTG ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5 A DC Maximum DC reverse current at rated DC blocking voltage per leg @ T A = 2 5 oC IR @ TA = 100oC 200 uAmps 2002-9 SYHMBOL VF HMB11PT HMB12PT 1.1 5.0 HMB13PT UNITS Volts uAmps NOTES : 1. On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.27 X 1.27 mm) pads 2. On aluminum substrate P.C.B. with an area of 0.8 x 0.8 x 0.25" (20 x 20 x 6.4mm) mounted on 0.05 x 0.05" (1.27 x 1.27mm) solder pad 3. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 0.016(0.41) 0.006(0.15) 0.195(4.95) 0.205(5.21) Amps nSec pF o C/W o C RATING CHARACTERISTIC CURVES ( HMB11PT THRU HMB13PT ) AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm -0.25A FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 0.75 Copper Pads .05 In2 (1.27mm2) PC Board (+) 25 Vdc (approx) (-) D.U.T 0.50 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.25 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT 1000 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 20 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS Pulse Width = 300uS 1% Duty Cycle 100 TJ =100oC 3.0 1.0 0.3 10 TJ =25oC 0.1 1 TJ =25oC .03 0.1 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .01 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 200 JUNCTION CAPACITANCE, ( pF ) 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 f = 1.0MHZ Vsig = 50 mVp-p TJ =25oC PEAK FORWARD SURGE CURRENT, ( A ) FIG. 6 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER BRIDGE ELEMENT 35 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 Single Half Sine-Wave (JEDEC Method)