HPL25CTPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED H IGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 2.0 Ampere FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals 0.081 (2.05) 0.077 (1.95) (3) H PL21CT PT THRU HPL28CT PT PROVISIONAL SPEC. SMP 0.170 (4.31) 0.163 (4.15) (1) 0.077 (1.95) 0.073 (1.85) 0.005 (0.15 Min.) (2) 0.019 (0.50 Min.) 0.045 (1.16) 0.042 (1.07) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) 0.212 (5.38) 0.208 (5.29) CIRCUIT (2) (1) 0.055 (1.40) 0.051 (1.30) (3) Dimensions in inches and (millimeters) SMP UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 110 C Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 15 -65 to +150 12 pF o o SYMBOL VRRM VRMS VDC IO HPL21CTPT HPL22CTPT HPL23CTPT HPL24CTPT HPL25CTPT HPL26CTPT HPL27CTPT HPL28CTPT 50 35 50 100 70 100 200 140 200 300 210 300 2.0 400 280 400 600 420 600 800 560 800 1000 700 1000 30 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC Maximum Full Load Reverse Current Average, Full Cycle at TA = 55oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A SYMBOL VF HPL21CTPT HPL22CTPT HPL23CTPT HPL24CTPT HPL25CTPT HPL26CTPT HPL27CTPT HPL28CTPT UNITS Volts uAmps uAmps 1.0 1.3 5.0 1.5 1.7 IR 100 trr 50 70 nSec 2004-7 RATING CHARACTERISTIC CURVES ( HPL21CTPT THRU HPL28CTPT ) 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 3.0 (+) 25 Vdc (approx) (-) D.U.T 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A 1.0 NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PL2 6C L21 CT HP L24 TJ =100oC 1.0 TJ =25oC 0.1 .1 .01 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 1.8 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 35 JUNCTION CAPACITANCE, ( pF ) 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ =25oC HPL2 1 CT~H PL25 HP TJ =25oC HPL26 CT~HP CT L28CT HP L2 7C TP 10 PT HP TJ =125oC PT L2 1.0 CT ~H T~ HP L2 Pulse Width = 300uS 1% Duty Cycle TP T 3C TP T T TP PL2 5C ~H 8C TP T