MUR105PT

CHENMKO ENTERPRISE CO.,LTD HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 - 600 Volts FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low power loss, high efficiency * Low leakage * High current capability * High speed switching * High current surge * High reliability * High temperature soldering guaranteed : 260oC/10 seconds at terminals M UR105PT THRU MUR160PT CURRENT 1.0 Ampere DO-41 0.034(0.9) DIA. 0.028(0.7) 1.0(25.4) MIN. MECHANICAL DATA Case: JEDEC DO-41 molded plastic Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Weight: 0.35 gram 0.205(5.2) 0.166(4.2) 0.107(2.7) DIA. 0.080(2.0) 1.0(25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) DO-41 UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 35 Amps SYMBOL VRRM VRMS VDC IO MUR105PT MUR110PT MUR115PT MUR12PT0 MUR130PT MUR140PT MUR150PT MUR160PT 50 35 50 100 70 100 o 150 105 150 200 140 200 300 210 300 400 280 400 o 500 350 500 600 420 600 1.0@TA=130 C 1.0@TA=120 C Typical thermal resistance Operating and Storage Temperature Range R JA 52 -65 to +175 o C/W o TJ, TSTG C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TJ = 25oC Maximum Full Load Reverse Current Average, Full Cycle 0.375" (9.5mm) lead length at TJ = 150oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A SYMBOL VF MUR105PT MUR110PT MUR115PT MUR12PT0 MUR130PT MUR140PT MUR150PT MUR160PT UNITS Volts uAmps uAmps nSec 2001-6 0.90 2.0 1.25 5.0 150 50 IR 50 trr 25 RATING CHARACTERISTIC CURVES ( MUR105PT THRU MUR160PT ) 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 2.0 (+) 25 Vdc (approx) (-) D.U.T 1.0 MUR120PT~MUR160PT 1 NONINDUCTIVE 0.5 MUR105PT~MUR115PT OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm 0 0 Single Phase Half Wave 60Hz Resistive or Inductive Load 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ= 125oC MUR105PT~MUR115PT 10 TJ= 100oC 1.0 1.0 TJ= 25oC MUR120PT~MUR160PT 0.1 .1 0.01 TJ= 25oC Pulse Width = 300uS 1% Duty Cycle .01 0 20 40 60 80 100 120 140 0.001 0 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 35 JUNCTION CAPACITANCE, ( pF ) 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 200 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 8.3ms Single Half Sine-Wave (JEDEC Method) 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ= 25oC