U16U10PT

CHENMKO ENTERPRISE CO.,LTD SUPER FAST RECOVERY RECTIFIER VOLTAGE RANGE 100 - 400 Volts FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Dual rectifier construction, positive centertap * Glass passivated chip junctions * Low power loss * Low forward voltage, high current capability * High surge current capability * Superfast recovery times for high efficiency * High temperature soldering guaranteed : 260oC/10 seconds at terminals U 16U10PT THRU U16U40PT CURRENT 16 Amperes D2PAK 0.420(10.67) 0.380(9.69) 0.245(6.22) MIN. K 0.190(4.83) 0.160(4.06) 0.055(1.40) 0.045(1.14) 0.055(1.40) 0.047(1.19) 0.575(14.60) 0.360(9.14) MECHANICAL DATA Case: JEDEC D2PAK molded plastic Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Weight: 0.08 ounces, 2.24 grams 0.625(15.88) 0.320(8.13) 1 K 2 0.110(2.79) 0.090(2.29) 0.100(2.54) 0.095(2.41) PIN 1 0.037(0.940) 0.027(0.686) 0.025(0.64) 0.018(0.46) 0.110(2.79) 0.080(2.03) K - HEATSINK MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. o PIN 2 Dimensions in inches and (millimeters) D2PAK U16U40PT 400 280 400 UNITS Volts Volts Volts Amps Amps pF o MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction capacitance per leg ( NOTE 1 ) Typical thermal resistance ( NOTE 2 ) Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO IFSM CJ R JC U16U10PT 100 70 100 U16U20PT 200 140 200 16.0 200 85 2.2 U16U30PT 300 210 300 C/W o TJ, TSTG -55 to +150 C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 8.0 A DC Maximum DC reverse current at rated DC blocking voltage per leg Maximum reverse recovery time ( NOTE 3 ) per leg TC = 25 C TC = 100oC o SYMBOL VF IR trr U16U10PT U16U20PT 0.975 5.0 150 35 U16U30PT U16U40PT 1.30 UNITS Volts uAmps 50 nS 2002-5 NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts 2. Thermal resistance from junction to case per leg mounted on heatsink 3. Reverse recovery test conditions : IF = 0.5 A, Ir = -1.0 A, Irr = -0.25 A. RATING CHARACTERISTIC CURVES ( U16U10PT THRU U16U40PT ) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 16 200 150 125 100 50 25 0 0 2 4 6 8 10 20 40 60 100 NUMBER OF CYCLES AT 60HZ FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS REVERSE CURRENT, (uA) 8.3 ms Single Half Sine-Wave (JEDEC Method) FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 12 8 Single Half Wave 60HZ Resistive or Inductive Load 4 0 0 25 50 75 100 125 150 CASE TEMPERATURE, ( oC ) FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARCTERISTICS 120 INSTANTANEOUS FORWARD CURRENT, (A) TJ = 25oC 100 U16U20PT U16U30PT&40PT TJ = 75oC 10 10 1.0 1.0 TJ = 25oC PULSE WIDTH=300uS 1% DUTY CYCLE 0.1 0 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 INSTANTANEOUS FORWARD VOLTAGE, (V) 0.1 0 20 40 60 80 100 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - TYPICAL JUNCTION CAPACITANCE 1000 JUNCTION CAPACITANCE, ( pF ) TJ =25oC 100 10 .1 .4 1.0 4 10 40 80 REVERSE VOLTAGE, ( V )