UPL101PT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED S UPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 - 400 Volts CURRENT 10 Amperes FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals 0.081 (2.05) 0.077 (1.95) (3) U PL10 1 PT THRU U PL105PT PROVISIONAL SPEC. SMP 0.170 (4.31) 0.163 (4.15) (1) 0.077 (1.95) 0.073 (1.85) 0.005 (0.15 Min.) (2) 0.019 (0.50 Min.) 0.045 (1.16) 0.042 (1.07) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) 0.212 (5.38) 0.208 (5.29) CIRCUIT 2 1 0.055 (1.40) 0.051 (1.30) 3 Dimensions in inches and (millimeters) SMP UPL105PT UNITS 400 280 400 Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 90 C Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 50 -55 to +150 30 pF o o SYMBOL VRRM VRMS VDC IO UPL101PT 50 35 50 UPL102PT 100 70 100 UPL103PT 200 140 200 8.0 UPL104PT 300 210 300 120 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 10.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A @ T A = 2 5 oC @ TA = 100oC IR 500 trr 35 50 uAmps nSec 2004-7 SYMBOL VF UPL101PT UPL102PT 0.975 10 UPL103PT UPL104PT 1.30 UPL105PT UNITS 1.50 Volts uAmps RATING CHARACTERISTIC CURVES ( UPL101PT THRU UPL105PT ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10 nS/cm -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 10 8.0 6.0 4.0 2.0 0 0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 100 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ =25oC UPL104PT UPL101PT~UPL103PT 10 TJ =125oC 10 1.0 TJ =100oC UPL105PT 1.0 .1 TJ =25oC .1 Pulse Width = 300uS 1% Duty Cycle .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .01 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 2.0 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 140 JUNCTION CAPACITANCE, ( pF ) 120 100 80 60 40 20 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ =25oC UPL1 01PT ~UPL UPL10 103P T 4PT~ UPL10 5PT