CS52015-1GDPR3

CS52015-1 CS52015-1 1.5A Adjustable Linear Regulator Description The CS52015-1 linear regulator provides 1.5A with an accuracy of ±1%. The device uses two external resistors to set the output voltage within a 1.25V to 5.5V range. The regulator is intended for use as a post regulator and microprocessor supply. The fast loop response and low dropout voltage make this regulator ideal for applications where low voltage operation and good transient response are important. The circuit is designed to operate with dropout voltages less than 1.4V at 1.5A output current. Device protection includes overcurrent and thermal shutdown. The CS52015-1 is pin compatible with the LT1086 family of linear regulators but has lower dropout voltage. The regulator is available in TO220, surface mount D2, and SOT-223 packages. Features s Output Current to 1.5A s Output Accuracy to ±1% Over Temperature s Dropout Voltage (typical) 1.05V @ 1.5A s Fast Transient Response s Fault Protection Current Limit Thermal Shutdown Application Diagram Package Options 3L TO-220 5.0V Tab (VOUT) 3L D2PAK Tab (VOUT) VIN VOUT CS52015-1 Adj 124W 1% 22mF 5V 200W 1% 3.3V @ 1.5A 1 10 mF 5V 0.1mF 5V Tantalum SOT-223 1 Tab (VOUT) CS52015 -1 1 Adj 2 VOUT (Tab) 3 VIN 1 Consult factory for fixed output voltage versions. Cherry Semiconductor Corporation 2000 South County Trail, East Greenwich, RI 02818 Tel: (401)885-3600 Fax: (401)885-5786 Email: info@cherry-semi.com Web Site: www.cherry-semi.com Rev. 2/17/98 1 A ¨ Company CS52015-1 Absolute Maximum Ratings Supply Voltage, VCC ....................................................................................................................................................................7V Operating Temperature Range................................................................................................................................-40¡C to 70¡C Junction Temperature ............................................................................................................................................................150¡C Storage Temperature Range ..................................................................................................................................-60¡C to 150¡C Lead Temperature Soldering Wave Solder (through hole styles only) .....................................................................................10 sec. max, 260¡C peak Reflow (SMD styles only) ......................................................................................60 sec. max above 183¡C, 230¡C peak ESD Damage Threshold............................................................................................................................................................2kV Electrical Characteristics: CIN = 10µF, COUT = 22µF Tantalum, VOUT + VDROPOUT < VIN < 7V, 0¡C ² TA ² 70¡C, TJ ² +150¡C, unless otherwise specified, Ifull load = 1.5A. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT s Adjustable Output Voltage (CS52015-1) Reference Voltage (Notes 1 and 2) Line Regulation Load Regulation (Notes 1 and 2) Dropout Voltage (Note 3) Current Limit Adjust Pin Current Thermal Regulation (Note 5) Ripple Rejection (Note 5) Thermal Shutdown (Note 6) Thermal Shutdown Hysteresis (Note 6) VINÐVOUT=1.5V; VAdj = 0V 10mA²IOUT²1.5A 1.5V²VINÐVOUT²5.75V; IOUT=10mA VINÐVOUT=1.5V; 10mA²IOUT²1.5A IOUT=1.5A VINÐVOUT=3V; TJ ³ 25¡C VINÐVOUT=3V; IOUT=10mA 30ms pulse; TA=25¡C f=120Hz; IOUT=1.5A; VINÐVOUT=3V; VRIPPLE=1VPP 150 1.6 1.241 (-1%) 1.254 0.02 0.04 1.05 3.1 0.6 50 0.002 80 180 25 210 2.0 100 0.020 1.266 (+1%) 0.20 0.4 1.4 V % % V A mA µA %/W dB ¡C ¡C Minimum Load Current (Note 4) VIN=7V ; VAdj=0 Note 1: Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output voltage due to temperature changes must be taken into account separately. Note 2: Specifications apply for an external Kelvin sense connection at a point on the output pin 1/4Ó from the bottom of the package. Note 3: Dropout voltage is a measurement of the minimum input/output differential at full load. Note 4: The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider used to set the output voltage is selected to meet the minimum requirement. Note 5: Guaranteed by design, not 100% tested in production. Note 6: Thermal shutdown is 100% functionally tested in production. Package Pin Description PACKAGE PIN # PIN SYMBOL FUNCTION D2PAK 1 2 3 TO-220 1 2 3 SOT-223 1 2 3 Adj VOUT VIN Adjust pin (low side of the internal reference. Regulated output voltage (case). Input voltage 2 CS52015-1 Block Diagram V OUT V IN Output Current Limit Thermal Shutdown + Error Amplifier Adj Bandgap Typical Performance Characteristics 1.05 0.10 0.08 TCASE 0ûC Output Voltage Deviation (%) 1.00 V Drop Out (V) 0.06 0.04 0.02 0.00 -0.02 -0.04 -0.06 -0.08 -0.10 -0.12 0 10 20 30 40 50 60 70 80 90 100 110 120 130 0.95 TCASE 25ûC 0.90 0.85 0.80 TCASE 125ûC 0.75 0 300 600 IOUT (mA) 900 1200 1500 TJ (°C) Dropout Voltage vs. Output Current Reference Voltage vs. Temperature 0.100 0.65 Minimum Load Current (mA) Output Voltage Deviation (%) 0.60 TCASE = 0°C 0.55 TCASE = 125°C TCASE = 25°C 0.075 0.050 TCASE = 25°C TCASE = 125°C 0.50 0.025 0.45 CIN =COUT =22mF Tantalum 0.40 TCASE = 0°C 0.000 0 1 Output Current (A) 2 1 2 3 4 VIN – VOUT (V) 5 6 7 Load Regulation vs. Output Current Minimum Load Current vs VIN-VOUT 3 CS52015-1 Typical Performance Characteristics 70.0 IO = 10mA 65.0 Adjust Pin Current (mA) Ripple Rejection (dB) 85 75 65 55 45 35 60.0 55.0 50.0 TCASE = 25°C IOUT = 1.5A (VIN Ð VOUT) = 3V VRIPPLE = 1.0VPP CAdj = 0.1mF 45.0 25 15 0 10 20 30 40 50 60 70 80 90 100 110 120 130 101 102 103 104 105 106 Temperature (°C) Frequency (Hz) 40.0 Adjust Pin Current vs. Temperature Ripple Rejection vs. Frequency Voltage Deviation (mV) 3.5 200 100 0 3.3 3.1 2.9 2.7 ISC(A) 10 -100 -200 VOUT=3.3V COUT =CIN =22mF Tantalum CAdj =0.1mF 2.5 2.3 2.1 1.9 Load Step (mA) 1500 750 1.7 0 0 1 2 3 4 5 Time mS 6 7 8 9 1.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VIN - VOUT (V) 5.0 5.5 6.0 6.5 7.0 Transient Response Short Circuit Current vs VIN-VOUT Applications Information The CS52015-1 linear regulator provides adjustable voltages at currents up to 1.5A. The regulator is protected against overcurrent conditions and includes thermal shutdown. The CS52015-1 has a composite PNP-NPN output transistor and requires an output capacitor for stability. A detailed procedure for selecting this capacitor is included in the Stability Considerations section. Adjustable Operation 50µA) also flows through R2 and adds a small error that should be taken into account if precise adjustment of VOUT is necessary. The output voltage is set according to the formula: VOUT = VREF ´ R1 + R2 + IAdj ´ R2 R1 The term IAdj ´ R2 represents the error added by the adjust pin current. R1 is chosen so that the minimum load current is at least 2mA. R1 and R2 should be the same type, e.g. metal film for best tracking over temperature. While not required, a bypass capacitor from the adjust pin to ground will improve ripple rejection and transient response. A 0.1µF tantalum capacitor is recommended for Òfirst cutÓ design. Type and value may be varied to obtain optimum performance vs price. ( ) The 52015-1 has an output voltage range of 1.25V to 5.5V. An external resistor divider sets the output voltage as shown in Figure 1. The regulator maintains a fixed 1.25V (typical) reference between the output pin and the adjust pin. A resistor divider network R1 and R2 causes a fixed current to flow to ground. This current creates a voltage across R2 that adds to the 1.25V across R1 and sets the overall output voltage. The adjust pin current (typically 4 CS52015-1 Applications Information: continued EXTERNAL SUPPLY VIN C1 VIN VOUT VOUT VREF R1 Adj C2 CS52015-1 VIN VOUT VAdj IAdj CAdj R2 VOUT Figure 1. Resistor divider scheme. The CS52015-1 linear regulator has an absolute maximum specification of 7V for the voltage difference between VIN and VOUT. However, the IC may be used to regulate voltages in excess of 7V. The main considerations in such a design are power-up and short circuit capability. In most applications, ramp-up of the power supply to VIN is fairly slow, typically on the order of several tens of milliseconds, while the regulator responds in less than one microsecond. In this case, the linear regulator begins charging the load as soon as the VIN to VOUT differential is large enough that the pass transistor conducts current. The load at this point is essentially at ground, and the supply voltage is on the order of several hundred millivolts, with the result that the pass transistor is in dropout. As the supply to VIN increases, the pass transistor will remain in dropout, and current is passed to the load until VOUT reaches the point at which the IC is in regulation. Further increase in the supply voltage brings the pass transistor out of dropout. The result is that the output voltage follows the power supply ramp-up, staying in dropout until the regulation point is reached. In this manner, any output voltage may be regulated. There is no theoretical limit to the regulated voltage as long as the VIN to VOUT differential of 7V is not exceeded. However, the possibility of destroying the IC in a short circuit condition is very real for this type of design. Short circuit conditions will result in the immediate operation of the pass transistor outside of its safe operating area. Overvoltage stresses will then cause destruction of the pass transistor before overcurrent or thermal shutdown circuitry can become active. Additional circuitry may be required to clamp the VIN to VOUT differential to less than 7V if failsafe operation is required. One possible clamp circuit is illustrated in figure 2; however, the design of clamp circuitry must be done on an application by application basis. Care must be taken to ensure the clamp actually protects the design. Components used in the clamp design must be able to withstand the short circuit condition indefinitely while protecting the IC. Figure 2: Short Circuit Protection Circuit for High Voltage Application. Stability Considerations The output or compensation capacitor helps determine three main characteristics of a linear regulator: start-up delay, load transient response and loop stability. The capacitor value and type is based on cost, availability, size and temperature constraints. A tantalum or aluminum electrolytic capacitor is best, since a film or ceramic capacitor with almost zero ESR can cause instability. The aluminum electrolytic capacitor is the least expensive solution. However, when the circuit operates at low temperatures, both the value and ESR of the capacitor will vary considerably. The capacitor manufacturersÕ data sheet provides this information. A 22µF tantalum capacitor will work for most applications, but with high current regulators such as the CS52015-1 the transient response and stability improve with higher values of capacitance. The majority of applications for this regulator involve large changes in load current so the output capacitor must supply the instantaneous load current. The ESR of the output capacitor causes an immediate drop in output voltage given by: ÆV = ÆI ´ ESR For microprocessor applications it is customary to use an output capacitor network consisting of several tantalum and ceramic capacitors in parallel. This reduces the overall ESR and reduces the instantaneous output voltage drop under load transient conditions. The output capacitor network should be as close as possible to the load for the best results. Protection Diodes When large external capacitors are used with a linear regulator it is sometimes necessary to add protection diodes. If the input voltage of the regulator gets shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage and the rate at which VIN drops. In the CS52015-1 linear regulator, the discharge path is through a large junction and protection diodes are not usually needed. If the regulator is used with large values of output capacitance and the input voltage is instantaneously shorted to ground, damage can occur. In this case, a diode connected as shown in Figure 2 is recommended. 5 CS52015-1 Applications Information: continued Thermal compound should always be used with high current regulators such as these. IN4002 VIN C1 VIN (optional) VOUT VOUT The thermal characteristics of an IC depend on the following four factors: 1. Maximum Ambient Temperature TA (¡C) 2. Power dissipation PD (Watts) CS52015-1 R1 Adj C2 3. Maximum junction temperature TJ (¡C) 4. Thermal resistance junction to ambient RQJA (C/W) CAdj R2 These four are related by the equation TJ = TA + PD ´ RQJA (1) Figure 3. Protection diode scheme for Large Output Capacitors. The maximum ambient temperature and the power dissipation are determined by the design while the maximum junction temperature and the thermal resistance depend on the manufacturer and the package type. The maximum power dissipation for a regulator is: PD(max)={VIN(max)ÐVOUT(min)}IOUT(max)+VIN(max)IQ where VIN(max) is the maximum input voltage, VOUT(min) is the minimum output voltage, IOUT(max) is the maximum output current, for the application IQ is the maximum quiescent current at IOUT(max). A heat sink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment has a thermal resistance. Like series electrical resistances, these resistances are summed to determine RQJA, the total thermal resistance between the junction and the surrounding air. 1. Thermal Resistance of the junction to case, RQJC (¡C/W) RLOAD Output Voltage Sensing Since the CS52015-1 is a three terminal regulator, it is not possible to provide true remote load sensing. Load regulation is limited by the resistance of the conductors connecting the regulator to the load. For the adjustable regulator, the best load regulation occurs when R1 is connected directly to the output pin of the regulator as shown in Figure 3. If R1 is connected to the load, RC is multiplied by the divider ratio and the effective resistance between the regulator and the load becomes RC ´ R1 + R2 R1 (2) ( ) RC conductor parasitic resistance RC = conductor parasitic resistance VIN VIN VOUT CS52015-1 R1 Adj 2. Thermal Resistance of the case to Heat Sink, RQCS (¡C/W) 3. Thermal Resistance of the Heat Sink to the ambient air, RQSA (¡C/W) R2 These are connected by the equation: RQJA = RQJC + RQCS + RQSA Figure 4. Grounding scheme for the adjustable output regulator to minimize parasitic resistance effects. (3) The value for RQJA is calculated using equation (3) and the result can be substituted in equation (1). The value for RQJC is 3.5ûC/W. For a high current regulator such as the CS52015-1 the majority of the heat is generated in the power transistor section. The value for RQSA depends on the heat sink type, while RQCS depends on factors such as package type, heat sink interface (is an insulator and thermal grease used?), and the contact area between the heat sink and the package. Once these calculations are complete, the maximum permissible value of RQJA can be calculated and the proper heat sink selected. For further discussion on heat sink selection, see application note ÒThermal Management for Linear Regulators.Ó Calculating Power Dissipation and Heat Sink Requirements The CS52015-1 linear regulator includes thermal shutdown and current limit circuitry to protect the device. High power regulators such as these usually operate at high junction temperatures so it is important to calculate the power dissipation and junction temperatures accurately to ensure that an adequate heat sink is used. The case is connected to VOUT on the CS52015-1, and electrical isolation may be required for some applications. 6 CS52015-1 Package Specification PACKAGE DIMENSIONS IN mm (INCHES) 3 Lead TO-220 (T) Straight PACKAGE THERMAL DATA Thermal Data RQJC typ RQJA typ 1.40 (.055) 1.14 (.045) 3L TO-220 3.5 50 3L D2PAK 3.5 10 - 50* 3L SOT-223 15 156 ûC/W ûC/W *Depending on thermal properties of substrate. RQJA = RQJC + RQCA 10.54 (.415) 9.78 (.385) 2.87 (.113) 2.62 (.103) 3.96 (.156) 3.71 (.146) 4.83 (.190) 4.06 (.160) 6.55 (.258) 5.94 (.234) 14.99 (.590) 14.22 (.560) 3 Lead SOT-223 (ST) 6.70 (.264) 6.30 (.248) 7.30 (.287) 6.70 (.264) 3.15 (.124) 2.95 (.116) 1.52 (.060) 1.14 (.045) 14.22 (.560) 13.72 (.540) 1.40 (.055) 1.14 (.045) 6.17 (.243) REF 3.70 (.146) 3.30 (.130) 1.02 (.040) 0.63 (.025) 2.79 (.110) 2.29 (.090) 5.33 (.210) 4.83 (.190) 0.56 (.022) 0.38 (.014) 2.92 (.115) 2.29 (.090) 2.30 (.090) 1.05 (.041) 0.85 (.033) 1.70 (.067) 1.50 (.060) 0.85 (.033) 0.65 (.026) 4.60 (.181) 1.30 (.051) 1.10 (.043) 10° MAX 0.35 (.014) 0.25 (.010) 3 Lead D2PAK (DP) 10.31 (.406) 10.05 (.396) 1.68 (.066) 1.40 (.055) 1.40 (.055) 1.14 (.045) 0.10 (.004) 0.02 (.001) 8.53 (.336) 8.28 (.326) 15.75 (.620) 14.73 (.580) 2.74(.108) 2.49(.098) 1.40 (.055) 1.14 (.045) 0.91 (.036) 0.66 (.026) 2.54 (.100) REF .254 (.010) REF 2.79 (.110) 2.29 (.090) 4.57 (.180) 4.31 (.170) 0.10 (.004) 0.00 (.000) Ordering Information Part Number CS52015-1GT3 CS52015-1GDP3 CS52015-1GDPR3 CS52015-1GST3 CS52015-1GSTR3 Rev. 2/17/98 Type 1.5A, adj. output 1.5A, adj. output 1.5A, adj. output 1.5A, adj. output 1.5A, adj. output Description 3 L TO-220 Straight 3 L D2PAK 3 L D2PAK (tape & reel) SOT-223 SOT-223 (tape & reel) Cherry Semiconductor Corporation reserves the right to make changes to the specifications without notice. Please contact Cherry Semiconductor Corporation for the latest available information. 7 © 1999 Cherry Semiconductor Corporation