CS8312YN8

CS8312 CS8312 IGBT Ignition Predriver with Dynamic Current Regulation Description The CS8312 is a bipolar microprocessor interface IC designed to drive an IGBT (or logic level MOSFETs) powering large inductive loads in harsh operating environments. The ICÕs dynamic current limit function lets the microprocessor adjust the current limit threshold to the real time needs of the system. CLI, the current limit input, sets the current limit for the IGBT high or low as directed by the system microprocessor. CLI also raises and lowers the threshold on the diagnostic FLAG output signal. The FLAG output signals the microprocessor when the current level approaches current limit on the IGBT. The CTRL input enables the FLAG function. Features s µP Compatible Inputs s Adjustable Current Limit Thresholds s External Sense Resistor s Flag Signal to Indicate Output Status Absolute Maximum Ratings Supply Voltage.................................................................................-0.3V to +12V Digital Input Currents....................................................................................2mA Internal Power Dissipation (TA = 25¡C) .................................................700mW Junction Temperature Range.....................................................-40¡C to +150¡C Storage Temperature Range ......................................................-55¡C to +165¡C Lead Temperature Soldering Wave Solder(through hole styles only).............10 sec. max, 260¡C peak Reflow (SMD styles only).............60 sec. max above 183¡C, 230¡C peak Electrostatic Discharge (Human Body Model) ............................................2kV Package Options 8L PDIP & SO Narrow FLAG 1 SENSE+ VCC CTRL CLI OUT Block Diagram VCC CTRL VT Control Logic Gate Driver OUT SENSEÐ Gnd FLAG Latch VT SENSE+ VREF Gnd CLI SENSEÐ Cherry Semiconductor Corporation 2000 South County Trail, East Greenwich, RI 02818 Tel: (401)885-3600 Fax: (401)885-5786 Email: info@cherry-semi.com Web Site: www.cherry-semi.com Rev. 4/7/97 1 A ¨ Company CS8312 Electrical Characteristics 7V ² VCC ² 10V; -40¡C ² TA ² +125¡C; unless otherwise specified PARAMETER TEST CONDITIONS MIN TYP MAX UNIT s General Power Supply including Ripple Voltage Supply Ripple Frequency Differential Ground Voltage Differential Ground Frequency Quiescent Current, IQ Turn On Turn Off Supply Voltage Rejection Differential Ground Rejection Ratio Differential Ground Current Ratio Unity Gain Bandwidth Clamp Voltage Output Off Voltage Turn On Delay Turn Off Delay s Control Function Input Voltage Range Input Threshold Turn On Turn Off Hysteresis Voltage Input Capacitance 7 10 -0.1 -0.2 10 10 60 1.0 0.6 60 15 5 V kHz V V kHz mA mA dB dB mA DC SENSE- to Gnd AC SENSE- to Gnd VCTRL=5.5V VCTRL=-0.3V VCTRL=5.5V VCTRL=5.5V VCTRL= -0.3V (VSENSE--VGnd)DC=1V (VSENSE--VGnd)AC=0.6V VCTRL=5.5V VCTRL=5.5V; IOUT=1mA VCTRL=-0.3V; IOUT=10µA VCTRL=-0.3V; IOUT=200µA CTRL increasing CTRL decreasing 30 30 3 400 5.5 0.5 1.2 30 30 kHz V V V us us ICTRL=2mA CTRL increasing CTRL decreasing ICTRL=10µA MAX -0.3 5.5 3.5 V V V V V pF 1.5 0.4 2.0 1.1 50 s Current Limit Increase Function Input Voltage Range ICTRL=2mA Input Threshold Turn On Turn Off Hysteresis Voltage Input Capacitance s Output Stage IOUT s Flag Function Output Low Leakage Current Output Capacitance Turn On (VSENSE+ Ð VSENSE-) CLI increasing CLI decreasing ICLI=10µA max -0.3 5.5 3.5 V V V V V pF 1.5 0.4 2.0 1.1 50 5 mA VCTRL=5.5V; IFLAG=1.5mA VCTRL=-0.3V VCTRL=5.5V; VCLI=-0.3V VCTRL=5.5V; VCLI=5.5V 2 210 300 225 0.9 10 50 240 350 V µA pF mV mV CS8312 Electrical Characteristics continued PARAMETER TEST CONDITIONS MIN TYP MAX UNIT s Flag Function: continued Turn Off Delay Turn On Delay Disable Time s Sense Function Input Voltage Range Sense Regulation Voltage Input Leakage Current Propagation Delay CTRL decreasing 100 10 10 450 us us us VCTRL=5.5V; VCLI=-0.3V VCTRL=5.5V; VCLI=5.5V VCTRL=5.5V VCTRL=5.5V -0.3 270 380 295 410 2.5 320 440 5 20 V mV mV µA us Package Pin Description PACKAGE PIN # PIN SYMBOL FUNCTION 8L PDIP & SO 1 2 3 4 5 6 7 8 FLAG SENSE+ SENSEÐ Gnd OUT CLI CTRL VCC Indicates whether current through the IGBT has reached a preset level. Positive input to current comparator. Ground (SENSE-) for current sense resistor. Ground connection. Output voltage to IGBT (MOSFET) gate. Current limit input increase. Control input. Supply voltage. Circuit Description Flag Function (see Application Diagram) Output Stage The flag indicates when the voltage across the two sense pins is approaching a current limit level that has been determined by the value of the external sense resistor (RSENSE) and the state of the CTRL and CLI pins. If the voltage across the sense pins (SENSE+, SENSE-) is less than the flag turn-on voltage, then the FLAG is off. When the voltage between the sense pins equals the FLAG turn on voltage, the FLAG will latch on until the CTRL pin goes low. FLAG is disabled whenever CTRL is low. Changing the CLI pin from low to high will increase nominal FLAG turn on voltage by approximately 45%. Table 1 FLAG Timing Sequence State 0 1 2 3 0 CONTROL Low High High High Low SENSE+ X Below Threshold Above Threshold X X FLAG OFF OFF ON ON OFF The CS8312 output (OUT) saturates and supplies voltage to the IGBT (or MOSFET) gate once the CTRL switches from low to high. As current through the IGBT (MOSFET) increases and the voltage across the sense resistor passes the flag turn on voltage, the FLAG will turn on. If the current through the sense resistor continues to rise and the sense resistor voltage reaches the regulation sense voltage, then the gate voltage will fall to a level that regulates the driver and maintains the regulation sense voltage at the sense resistor. Current Limit Function Changing the CLI pin from a logic low to a logic high increases the FLAG turn on voltage by approximately 45% and the regulation sense voltage by approximately 39% respectively. 3 CS8312 Application and Test Diagram VCC VBA T 0.1mF VCC VCC OUT R LOAD CS8312 FLAG CTRL CLI SENSE+ RSENSE SENSEÐ Gnd Microprocessor 4 CS8312 Package Specification PACKAGE DIMENSIONS IN mm (INCHES) PACKAGE THERMAL DATA D Lead Count 8 Lead SO Narrow 8 Lead PDIP Metric Max Min 5.00 4.80 10.16 9.02 English Max Min .197 .189 .400 .355 Thermal Data RQJC RQJA typ typ 8L SO 45 165 8L PDIP 52 100 ûC/W ûC/W Surface Mount Narrow Body (D); 150 mil wide 4.00 (.157) 3.80 (.150) 6.20 (.244) 5.80 (.228) 0.51 (.020) 0.33 (.013) 1.27 (.050) BSC 1.75 (.069) MAX 1.57 (.062) 1.37 (.054) 1.27 (.050) 0.40 (.016) 0.25 (.010) 0.19 (.008) D REF: JEDEC MS-012 0.25 (0.10) 0.10 (.004) Plastic DIP (N); 300 mil wide 7.11 (.280) 6.10 (.240) 8.26 (.325) 7.62 (.300) 3.68 (.145) 2.92 (.115) 1.77 (.070) 1.14 (.045) 2.54 (.100) BSC .356 (.014) .203 (.008) 0.39 (.015) MIN. .558 (.022) .356 (.014) Some 8 and 16 lead packages may have 1/2 lead at the end of the package. All specs are the same. REF: JEDEC MS-001 D Ordering Information Part Number CS8312YN8 CS8312YD8 CS8312YDR8 Rev. 4/7/97 Description 8L PDIP 8L SO Narrow 8L SO Narrow (tape & reel) 5 Cherry Semiconductor Corporation reserves the right to make changes to the specifications without notice. Please contact Cherry Semiconductor Corporation for the latest available information. © 1999 Cherry Semiconductor Corporation