CS3004_09

CS3004 Precision Low-voltage Amplifier Features & Description      – 10 μV Max. – 0.05 μV/°C Max. – 17 nV/√Hz Description The CS3004 dual amplifier is designed for precision amplification of low-level signals. These amplifiers achieve excellent offset stability, hi gh open loop gain, and low noise. T he d evices also exhibit e xcellent CMRR an d PSRR. The common mode input range includes the supply rails. The amplifiers operate with any supply voltage from 2.7 V to 5 V (±1.35 V to ±2.50 V). Low Offset: Low Drift: Low Noise: Rail-to-Rail Inputs  Rail-to-Rail Output Swing – to within 10 mV of supply voltage   – 150 dB Typ. Open-loop Voltage Gain: Pin Configurations – 0.25 V s /μ     2.1 mA Supply Current Slew rate: CS3004 (Top View) Out A 1 -In A 2 +In A 3 V- 4 8-Lead SOIC 1. Must not be connected. 8 V+ A -+ B +7 Out B 6 -In B 5 +In B Applications Thermocouple/Thermopile Amplifiers Load Cell and Bridge Transducer Amplifiers Precision Instrumentation Battery-powered Systems 1000 200 150 100 100 50 0 10 -50 -100 -150 1 0.01 0.1 1 10 -200 0 1 2 3 4 5 6 7 8 9 10 Frequency (Hz) Time (sec) Noise vs. Frequency (Measured) 0.01 Hz to 10 Hz Noise Performance Cirrus Logic, Inc. http://www.cirrus.com Copyright  Cirrus Logic, Inc. 2009 (All Rights Reserved) JUL ‘09 DS719F2 CS3004 TABLE OF CONTENTS 1. CHARACTERISTICS AND SPECIFICATIONS ............................................. 3 1.1 5 V Electrical Characteristics ................................................................... 3 1.2 3 V Electrical Characteristics ................................................................... 4 1.3 Absolute Maximum Ratings ..................................................................... 5 2. TYPICAL PERFORMANCE PLOTS ............... ............................................... 5 3. PACKAGE DRAWINGS ................................................................................. 7 4. ORDERING INFORMATION .......................................................................... 8 5. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION ... 8 6. REVISION HISTORY .................................................................................... 9 LIST OF FIGURES Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Noise vs Frequency (Measured) .................................................................................5 0.01 Hz to 10 Hz Noise ................................................................................................5 Gain & Phase vs. Frequency (2.7 V)............................................................................5 Gain & Phase vs. Frequency (5 V) ..............................................................................5 Supply Current vs. Supply Voltage ..............................................................................5 Supply Current vs. Temperature .................................................................................5 Voltage Swing vs. Output Current (2.7 V) ...................................................................6 Voltage Swing vs. Output Current (5 V) .......................................................................6 2 DS719F2 CS3004 1. CHARACTERISTICS AND SPECIFICATIONS 1.1 5 V Electrical Characteristics Parameter Input Offset Voltage Average Input Offset Drift Input Bias Current Input Offset Current Input Noise Voltage Density Input Noise Voltage Input Noise Current Density Input Noise Current Input Voltage Range Common Mode Rejection Ratio (dc) Power Supply Rejection Ratio Large Signal Voltage Gain (Note 3) Output Voltage Swing Slew Rate Overload Recovery Time Supply Current Oscillator Frequency Input Capacitance Differential Common Mode • RL = 2 kΩ to V+/2 RS = 100 Ω, f0 = 1 Hz RS = 100 Ω, f0 = 1 kHz 0.1 to 10 Hz f0 = 1 Hz 0.1 to 10 Hz (Note 2) • • • • • (Note 2) (Note 2) • • • • Min V110 110 120 (V+ – 100) (V+ – 10) Typ ±2 ±0.01 ±170 ±340 17 17 350 100 1.9 120 130 150 150 0.25 25 2.0 150 1.5 10 V+ (V- + 100 ) (V- + 10) 2.5 Max ±10 ±0.05 ±250 ±1.5 ±500 ±3.0 Unit µV µV/ºC pA nA pA nA nV/ Hz nV/ Hz V+ = +5 V, ±5%; V- = 0V; VCM = 2.5 V; Unless otherwise noted, TA = 25º C (See Note 1). - nVp-p fA/ Hz pAp-p V dB dB dB dB mV mV V/µs µs mA kHz pF pF RL = 2 kΩ to V+/2 (Note 4) RL = 100 kΩ to V+/2 RL = 2 k, 100 pF Notes: 1. Symbol “•” denotes specification applies over -40 to +125 ° C. 2. This parameter is guaranteed by design and/or laboratory characterization. 3. Guaranteed within the output limits of (V+ – 0.2 V) to (V- + 0.2 V). 4. Specifies the worst case drive voltage relative to the supply rail under stated load conditions. DS719F2 3 CS3004 1.2 3 V Electrical Characteristics Parameter Input Offset Voltage Average Input Offset Drift Input Bias Current Input Offset Current Input Noise Voltage Density Input Noise Voltage Input Noise Current Density Input Noise Current Input Voltage Range Common Mode Rejection Ratio (dc) Power Supply Rejection Ratio Large Signal Voltage Gain (Note 7) Output Voltage Swing Slew Rate Overload Recovery Time Supply Current Oscillator Frequency Input Capacitance Differential Common Mode • RL = 2 kΩ to V+/2 RS = 100 Ω, f0 = 1 Hz RS = 100 Ω, f0 = 1 kHz 0.1 to 10 Hz f0 = 1 Hz 0.1 to 10 Hz (Note 6) • • • • • (Note 6) (Note 6) • • • • Min V110 110 120 (V+ – 100) (V+ – 10) Typ ±2 ±0.01 ±110 ±220 17 17 350 100 1.9 120 130 160 150 0.25 25 2.0 150 1.5 10 V+ (V- + 100 ) (V- + 10) 2.5 Max ±10 ±0.05 ±150 ±1.0 ±300 ±2.0 Unit µV µV/ºC pA nA pA nA nV/ Hz nV/ Hz V+ = +3 V, ±10%; V- = 0V; VCM = 2.5 V; Unless otherwise noted, TA = 25º C (See Note 5). - nVp-p fA/ Hz pAp-p V dB dB dB dB mV mV V/µs µs mA kHz pF pF RL = 2 kΩ to V+/2 (Note 8) RL = 100 kΩ to V+/2 RL = 2 k, 100 pF Notes: 5. Symbol “•” denotes specification applies over -40 to +125 ° C. 6. This parameter is guaranteed by design and/or laboratory characterization. 7. Guaranteed within the output limits of (V+ – 0.2 V) to (V- + 0.2 V). 8. Specifies the worst case drive voltage relative to the supply rail under stated load conditions. 4 DS719F2 CS3004 1.3 Absolute Maximum Ratings Parameter Supply Voltage Input Voltage Storage Temperature Range [(V+) – (V-)] Min T 2.7 (V-) – 0.3 -65 yp Max 5.5 (V+) + 0.3 +150 Unit V V ºC 2. TYPICAL PERFORMANCE PLOTS 1000 200 150 100 100 50 0 10 -50 -100 -150 1 0.01 0.1 1 10 -200 0 1 2 3 4 5 6 7 8 9 10 Frequency (Hz) Time (sec) Figure 1. Noise vs Frequency (Measured) Figure 2. 0.01 Hz to 10 Hz Noise 180 160 140 120 100 80 60 40 20 0 -20 0.001 0.01 0.1 1 Frequency (Hz) 10 100 1k 10k 100k 1M 270 225 180 135 90 45 0 -45 -90 -135 -180 10M 180 160 140 120 100 80 60 40 20 0 -20 0.001 0.01 270 225 180 135 90 45 0 0.1 1 Frequency (Hz) 10 100 1k 10k 100k 1M -45 -90 -135 -180 10M Figure 3. Gain & Phase vs. Frequency (2.7 V) Figure 4. Gain & Phase vs. Frequency (5 V) 2.0 Supply Current (mA) Supply Current (mA) 1.9 1.8 1.7 1.6 1.5 2.5 3 3.5 4 4.5 5 5.5 2.5 2.0 1.5 1.0 0.5 -40 5V 2.7V -15 10 35 60 85 110 125 Supply voltage Temperature (°C) Figure 5. Supply Current vs. Supply Voltage Figure 6. Supply Current vs. Temperature DS719F2 5 CS3004 Typical Performance Plots (Cont.) V+ -50 -100 V+ +125°C -40°C -50 -100 +125°C -40°C Output Voltage (mV) -150 -200 Output Voltage (mV) +25°C -150 -200 +25°C +200 +150 +100 +50 V– -40°C +25°C +200 +150 +100 +50 -40°C +25°C +125°C +125°C 0 1 Output Current (mA) 2 3 4 5 V– 0 1 Output Current (mA) 2 3 4 5 Figure 7. Voltage Swing vs. Output Current (2.7 V) Figure 8. Voltage Swing vs. Output Current (5 V) 6 DS719F2 CS3004 3. PACKAGE DRAWINGS 8L SOIC (150 MIL BODY) PACKAGE DRAWING E H 1 b D SEATING PLANE e A1 A L c ∝ DIM A 0.0 A1 B C D E e H L ∝ MIN 53 0.004 0.013 0.007 0.189 0.150 0.040 0.228 0.016 0° INCHES MAX 0.069 0.010 0.020 0.010 0.197 0.157 0.060 0.244 0.050 8° MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.02 1.52 5.80 6.20 0.40 1.27 0° 8° JEDEC # : MS-012 DS719F2 7 CS3004 4. ORDERING INFORMATION Part # CS3004-FSZ Temperature Range -40 °C to +125 °C Package Description 8-lead SOIC, Lead Free 5. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION Model Number CS3004-FSZ Peak Reflow Temp 260 °C MSL Rating* 2 Max Floor Life 365 Days * MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020. 8 DS719F2 CS3004 6. REVISION HISTORY Revision PP4 F1 F2 Date FEB 2007 AUG 2007 JUL 2009 First public release. Updated to “Final” per QPL process. Removed lead-containing SOIC & QFN packages from ordering information. Changes DS719F2 9 CS3004 Contacting Cirrus Logic Support IMPORTANT NOTICE For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find one nearest you go to http://www.cirrus.com Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INC LUSION OF CIRRUS PRODUCTS IN S UCH APPLICATIONS IS U NDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUC H A M ANNER. IF TH E CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. 10 DS719F2