CS4953

CS4952/53 NTSC/PAL Digital Video Encoder Features Description The CS4952/3 provides full conversion from YCbCr or YUV digital video formats into NTSC & PAL Composite and Y/C (S-video) analog video. Input formats can be 27 MHz 8-bit YUV, 8-bit YCbCr, or CCIR656 with support for EAV/SAV codes. Output video can be formatted to be compatible with NTSC-M, or PAL B,D,G,H,I,M,N, and Combination N systems. Also supported is NTSC line 21 and line 284 closed captioning encoding. Four 9-bit DACs provide two channels for an S-Video output port and two composite video outputs. 2x oversampling reduces the output filter requirements and guarantees no DAC related modulation components within the specified bandwidth of any of the supported video standards. Parallel or high speed I2C compatible control interfaces are provided for flexibility in system design. The parallel interface doubles as a general purpose I/O port when the CS4952/3 is in I2C mode to help conserve valuable board area. ORDERING INFORMATION CS4952/3-CL 44 pin PLCC CS4952/3-CQ 44 pin TQFP VAA CLK SCL SDA PDAT[7:0] RD* WR* 8 Host Parallel Interface l Simultaneous composite and S-video output l Supports RS170A and CCIR601 composite output timing l Multi-standard support for NTSC-M, PAL (B, D, G, H, I, M, N, Combination N) l Optional progressive scan @ MPEG2 field rates l CCIR656 input mode supporting EAV/SAV codes and CCIR601 Master/Slave input modes l Stable color subcarrier for MPEG2 systems l NTSC closed caption encoder with interrupt l Supports Macrovision copy protection in CS4953 version l Host interface configurable for parallel or I2C compatible operation l General purpose input and output pins l Individual DAC power-down capability l On-chip voltage reference generator l On-chip color bar generator l +5 volt only, CMOS, low power modes, tri-state DACs I 2C Interface Control Registers Output Interpolate LPF 9-Bit DAC 9-Bit DAC Σ 9-Bit DAC C Chroma Amplifier Chroma Modulate Burst Insert Chroma Interpolate CVBS37 CVBS75 ADDR XTAL Color Sub-carrier Synthesizer 9-Bit DAC Y VD[7:0] 8 Video Formatter U, V Y LPF Luma Delay Luma Amplifier HSYNC* VSYNC* FIELD INT RESET* Sync Insert Video Timing Generator Output Interpolate GND LPF Voltage Reference Current Reference TEST VREFIN VREFOUT ISET Preliminary Product Information Cirrus Logic, Inc. Crystal Semiconductor Products Division P.O. Box 17847, Austin, Texas 78760 (512) 445 7222 FAX: (512) 445 7581 http://www.crystal.com This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice. Copyright © Cirrus Logic, Inc. 1997 (All Rights Reserved) OCT ‘97 DS223PP2 1 CS4952/53 TABLE OF CONTENTS AC & DC PARAMETRIC SPECIFICATIONS .....................................................................4 INTRODUCTION ...............................................................................................................11 FUNCTIONAL DESCRIPTION .........................................................................................11 Video Timing Generator .........................................................................................11 Video Input Formatter .............................................................................................11 Color Subcarrier Synthesizer ..................................................................................12 Chroma Path ..........................................................................................................12 Luma Path ..............................................................................................................12 Digital to Analog Converters ...................................................................................13 Voltage Reference ..................................................................................................13 Current Reference ..................................................................................................13 Host Interface .........................................................................................................13 Closed Caption Services ........................................................................................13 Control Registers ....................................................................................................13 OPERATIONAL DESCRIPTION .......................................................................................14 Reset Hierarchy ......................................................................................................14 Video Timing ...........................................................................................................14 Slave Mode Input Interface .............................................................................14 Master Mode Input Interface ...........................................................................14 Vertical Timing .................................................................................................15 Horizontal Timing ............................................................................................15 NTSC Interlaced ..............................................................................................17 PAL Interlaced .................................................................................................17 Progressive Scan ............................................................................................19 PAL Progressive Scan ....................................................................................19 NTSC Progressive Scan .................................................................................19 CCIR-656 ................................................................................................................19 Digital Video Input Modes .......................................................................................22 Multi-standard Output Format Modes .....................................................................22 Subcarrier Generation ............................................................................................22 Subcarrier Compensation .......................................................................................22 Closed Caption Insertion ........................................................................................23 Color Bar Generator ...............................................................................................23 Interrupts ................................................................................................................24 General Purpose I/O Port .......................................................................................24 ANALOG ...........................................................................................................................24 Analog Timing .........................................................................................................24 VREF ......................................................................................................................25 ISET ........................................................................................................................25 DACs ......................................................................................................................25 Luminance DAC ..............................................................................................25 Chrominance DAC ..........................................................................................25 CVBS75 DAC ..................................................................................................26 CVBS37 DAC ..................................................................................................26 PROGRAMMING ..............................................................................................................27 Host Control Interface .............................................................................................27 I2C Interface ....................................................................................................27 8-bit Parallel Interface .....................................................................................27 Register Description ...............................................................................................28 Control Register 0 ............................................................................................28 Control Register 1 ............................................................................................29 Control Register 2 ............................................................................................30 DAC Power Down Register ..............................................................................30 Status Register.................................................................................................31 Background Color Register ..............................................................................31 GPIO Control Register .....................................................................................31 GPIO Data Register .........................................................................................32 Chroma Filter Register .....................................................................................32 Luma Filter Register .........................................................................................32 I2C Address Register .......................................................................................32 Subcarrier Amplitude Register .........................................................................33 2 DS223PP2 CS4952/53 Subcarrier Synthesis Register ......................................................................... 33 Hue LSB Adjust Register ................................................................................. 33 Hue MSB Adjust Register ................................................................................ 33 Closed Caption Enable Register...................................................................... 34 Closed Caption Data Register ......................................................................... 34 Interrupt Enable Register ................................................................................. 34 Interrupt Clear Register.................................................................................... 35 Device ID Register ........................................................................................... 35 BOARD DESIGN & LAYOUT CONSIDERATIONS ......................................................... 36 Power and Ground Planes ..................................................................................... 36 Power Supply Decoupling ...................................................................................... 36 VREF Decoupling ................................................................................................... 36 Digital Interconnect ................................................................................................ 36 Analog Interconnect ............................................................................................... 37 Analog Output Protection ....................................................................................... 37 ESD Protection ....................................................................................................... 37 External DAC Output Filter ..................................................................................... 37 DEVICE PINOUT - 44 PLCC ............................................................................................ 38 PLCC Pin Description ............................................................................................ 39 DEVICE PINOUT - 44 TQFP ............................................................................................ 41 TQFP Pin Description ............................................................................................ 42 DS223PP2 3 CS4952/53 AC & DC PARAMETRIC SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS: (AGND, DGND = 0 V, all voltages with respect to 0 V.) Parameter Power Supply Input Current Per Pin Output Current Per Pin Analog Input Voltage Digital Input Voltage Ambient Temperature Storage Temperature Power Applied Except Supply Pins Except Supply Pins Symbol VAA Min -0.3 -10 -50 -0.3 -0.3 -55 -65 Max 6.0 10 +50 VAA+0.3 VAA+0.3 +125 +150 Units V mA mA V V °C °C Warning: Operating beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS: (AGND, DGND = 0 V, all voltages with respect to 0 V.) Parameter Power Supplies: Digital Analog Operating Ambient Temperature Symbol VAA TA Min 4.75 0 Typ 5.0 +25 Max 5.25 +70 Units V °C 4 DS223PP2 CS4952/53 D.C. CHARACTERISTICS: (TA=25 C; VAA = 5 V; GND = 0 V.) Min Typ Max Units Parameter Symbol Digital Inputs High Level Input Voltage V [7:0], PDAT [7:0], VIH HSYNC/VSYNC/FIELD/CLKIN VIH High Level Input Voltage I2C Low Level Input Voltage Input Leakage Current Digital Outputs High Level Output Voltage Low Level Output Voltage Low Level Output Voltage Output Leakage Current Analog Outputs Full Scale Output Current Full Scale Output Current LSB Current LSB Current DAC-to-DAC Matching Output Compliance Output Impedance Output Capacitance DAC Output Delay DAC Rise/Fall Time Voltage Reference Reference Voltage Output Reference Input Current Power Supply Supply Voltage Supply Current All DACs on CVBS75/CVGS37 only CVBS75 only (Note 2) All Inputs Digital Inputs Io = -4mA Io = 4mA SDA pin only, Io = 6mA High-Z Digital Outputs CVBS37/Y/C (Note 1) CVBS75 (Note 1) CVBS37/Y/C (Note 1) CVBS75 (Note 1) VIL VOH VOL VOL IO37 IO75 IB37 IB35 MAT VOC ROUT COUT ODEL TRF VOV IVC VAA IAA1 IAA2 IAA3 2.0 0.7VAA -0.3 -10 2.4 -10 32.9 16.4 64.5 32.2 0 1.198 4.75 - 34.7 17.3 68 34 2 15 4 2.5 1.232 5 180 110 75 VAA+0.3 0.8 +10 VAA 0.4 0.4 +10 36.5 18.2 71.5 35.8 +1.4 30 12 5 1.272 10 5.25 200 - V V V µA V V V µA mA mA µA µA % V kΩ pF ns ns V µA V mA mA mA Notes: 1. Output current levels with ISET = 10 kΩ, VREFIN = 1.232 V. 2. Times for black-to-white level and white-to-black level transitions. DS223PP2 5 CS4952/53 D.C. CHARACTERISTICS (Continued) Parameter Static Performance DAC Resolution Differential Non-Linearity Integral Non-Linearity Dynamic Performance Differential Gain Differential Phase Signal to Noise Ratio Hue Accuracy Saturation Accuracy Symbol Min -1 -1 -70 Typ ±0.5 ±0.35 2 ±0.5 Max 9 +1 +1 5 ±2 2 2 Units Bits LSB LSB % ° dB ° % DNL INL DB DP SNR HA SA 6 DS223PP2 CS4952/53 A.C. CHARACTERISTICS: Parameter Pixel Input and Control Port Symbol Min Typ Max Units Clock Pulse High Time Clock Pulse Low Time Clock to Data Set-up Time Clock to Data Hold Time Clock to Data Output Delay CLK Tch V[7:0] Tcl Tisu Tch Tcl Tisu Tih Toa 14.82 14.82 6 0 - 18.52 18.52 - 22.58 22.58 17 ns ns ns ns ns Tih HSYNC*/VSYNC* (Inputs) HSYNC*/VSYNC*/ CB/FIELD/INT (Outputs) Toa Figure 1. Video Pixel Data and Control Port Timing Parameter Symbol Fclk Tsph Tspl Tsh Tssu Tsds Tsr Tsf Tss Tbuf Tdh Tvdo Min 100 0.1 0.7 100 100 50 Typ Max 1000 Units KHz µs µs ns ns ns I2C Host Port Timing SCL Frequency Clock Pulse High Time Clock Pulse Low Time Hold Time (Start Condition) Setup Time (Start Condition) Data Setup Time Rise Time Fall Time Setup Time (Stop Condition) Bus Free Time Data Hold Time SCL Low to Data Out Valid Tbuf SDA Tsr SCL 1 0.3 100 100 0 600 Tsh Tss µs µs ns ns ns ns Tsh Tdh Tsds Tsph Tvdo Tspl Tsf Tssu Figure 2. I C Host Port Timing 2 DS223PP2 7 CS4952/53 A.C. CHARACTERISTICS: Parameter 8-bit Parallel Host Interface Read Cycle Time Read Pulse Width Address Setup Time Read Address Hold Time Read Data Access Time Read Data Hold Time Write Recovery Time Write Pulse Width Write Data Setup Time Write Data Hold Time Write-Read/Read-Write Recovery Time Address from Write Hold Time Trd RD* Trpw ADDR Trah (Continued) Symbol Trd Trpw Tas Trah Trda Trdh Twr Twpw Twds Twdh Trec Twac Min 60 30 3 10 10 60 40 8 3 50 0 Typ Max 40 50 Units ns ns ns ns ns ns ns ns ns ns ns ns PDAT[7:0] Tas Trda Trdh 8-bit Parallel Host Port Timing: Read Cycle Twpw WR* Twac ADDR Twr PDAT[7:0] Tas Twds Twdh 8-bit Parallel Host Port Timing: Address Write Cycle WR* Trec RD* Trec 8-bit Parallel Host Port Timing: Read-Write/Write-Read Cycle Figure 3. 8 DS223PP2 CS4952/53 A.C. CHARACTERISTICS: (Continued) Parameter Symbol Tres Min 100 Typ Max Units ns Reset Timing Reset Pulse Width RESET* Tres Figure 4. Reset Timing DS223PP2 9 CS4952/53 L1 Ferrite Bead +5V (Vcc) 4.7 µF 0.1 µF 1 NC 18 19 XTAL ADDR 3 20 29 VAA 42 VREFOUT 41 VREFIN 0.1 µF 8 GPIO Port +5V (Vcc) 31 32 PDAT[7:0] RD* WR* CVBS75 5 75Ω 4 75Ω To RF Modulator CVBS37 1.5kΩ I2 C Controller 110Ω 27 MHz Clock 1.5kΩ 110Ω Composite Video Connector 35 36 SDA CS4952 CS4953 Y SCL 43 75Ω 33 8 CLK Pixel Data 7-14 15 V[7:0] C 44 75Ω S-Video Connector FIELD HSYNC*/CB VSYNC* TEST INT RESET* GND 2 21 22 38 ISET 34 37 40 16 17 6 10 kΩ±1% Figure 5. Typical Connection Diagram (I2C host interface) 10 DS223PP2 CS4952/53 INTRODUCTION The CS4952/3 is a complete multi-standard digital video encoder implemented in current 5-volt only CMOS technology. CCIR601 or CCIR656 compliant digital video input can be converted into NTSC-M, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, or PAL N Argentina-compatible analog video. The CS4952/3 is designed to connect to MPEG1 and MPEG2 digital video decompressors without glue logic. Two 9-bit DAC outputs provide high quality S-Video analog output while two other 9-bit DACs simultaneously generate composite analog video. The CS4952/3 will accept 8-bit YCbCr or 8-bit YUV input data. The CS4952/3 is completely configured and controlled via an 8-bit host interface port or an I2C compatible serial interface. This host port provides access and control of all CS4952/3 options and features like closed caption insertion, interrupts, etc. In order to lower the end user set-top overall system costs, the CS4952/3 provides an internal voltage reference which eliminates the requirement for an external discrete 3-pin voltage reference. puts. It automatically disables color burst on appropriate scan lines and generates serration and equalization pulses on appropriate scan lines. The CS4952/3 is designed to function as a video timing master or video timing slave. In both Master and Slave Modes, all timing is sampled and asserted with the rising edge of the CLK pin. In most cases the CS4952/3 will serve as the video timing master. The master timing cannot be externally altered other than through the host interface by changing the video display modes: PAL or NTSC and Progressive Scan. HSYNC, VSYNC and FIELD are configured as outputs for Master Mode. HSYNC can also be defined as a composite blanking output signal in Master Mode. Exact horizontal and vertical display timing is addressed in section: Operational Description (page 14). In Slave Mode HSYNC and VSYNC are configured as input pins and are used to initialize independent vertical and horizontal timing generators upon their respective falling edges. FIELD remains an output in Slave Mode. The CS4952/3 also provides a CCIR-656 Slave Mode where the video input stream contains EAV and SAV codes. In this case, proper HSYNC VSYNC timing is extracted automatically without aid from any inputs other than the V [7:0]. CCIR-656 input data is sampled with the leading edge of CLK. Slave Mode vertical and horizontal timing derived via CCIR-656 or external hardware must be equivalent to timing generated by the CS4952/3 in Master Mode. FUNCTIONAL DESCRIPTION In the following subsections, the functions of the CS4952/3 will be described. The descriptions refer to the block diagram on the cover page. Video Timing Generator All timing generation is accomplished via a 27 MHz input applied to the CLK pin. The CS4952/3 can also accept an optional color burst crystal on the ADDR & XTAL pins. See section: Color Subcarrier Synthesizer (page 12), for further details. The Video Timing Generator is responsible for orchestrating most all of the other modules in the device. It works in harmony with external sync input timing or by providing external sync timing outDS223PP2 Video Input Formatter The video input formatter translates YCbCr input data into YUV information, if necessary, and splits the luma and chroma information for filtering, scaling, and modulation. 11 CS4952/53 Color Subcarrier Synthesizer The subcarrier synthesizer is a digital frequency synthesizer that produces the correct subcarrier frequency for NTSC or PAL. The CS4952/3 generates the color burst frequency based on the input CLK (27 MHz). Color burst accuracy and stability are limited by the accuracy of the 27 MHz input. If the frequency varies then the color burst frequency will also vary accordingly. In order to handle situations in which the CLK varies unacceptably, a local crystal frequency reference may be used on the ADDR & XTAL device pins. In this instance the input CLK is continuously compared with the external crystal reference input and the internal timing of the CS4952/3 is automatically adjusted so that the color burst frequency remains close to the requirements. Controls are provided for phase adjustment of the burst to permit color adjustment and phase compensation. Chroma hue control is provided by the CS4952/3 via a 10-bit Hue Control Register (HUE_LSB and H_MSB). Burst amplitude control is also made available to the host via the 8-bit burst amplitude register (SC_AMP). The output of the chroma low pass filter is connected to the chroma interpolation filter where upsampling from 4:2:2 to 4:4:4 is accomplished. The chroma digital data is fed to a quadrature modulator where they are combined with the output from the subcarrier synthesizer to produce the proper modulated chrominance signal. Following chroma modulation the chroma data passes through a variable gain amplifier where the chroma amplitude may be varied via the C_AMP 8-bit host addressable register. The chroma then is interpolated by a factor of 2 in order to operate the output DACs at 2 times the pixel rate. The interpolated filters help reduce the sinx/x roll-off for higher frequencies and reduce the complexity of the external analog low pass filters. Luma Path Along with the chroma output path, the CS4952/3 Video Input Formatter initiates a parallel luma data path by directing the luma data to a digital delay line. The delay line is built as a digital FIFO where the depth of the FIFO replicates the clock period delay associated with the more complex chroma path. Following the luma delay, the data is passed through a variable gain amplifier where the luma DC values are modifiable via the Y_AMP register. The output of the luma amplifier connects to the sync insertion block. Sync insertion is accomplished by multiplexing into the luma data path the different sync DC values at the appropriate times. The digital sync generator takes horizontal sync and vertical sync timing signals and generates the appropriate composite sync timing (including vertical equalization and serration pulses), blanking information, and burst flag. The sync edge rates conform to RS-170A or CCIR specifications. The luma only path is concluded via output interpolation by a factor of two in order to operate the output DACs at two times the pixel rate. DS223PP2 Chroma Path The Video Input Formatter at conclusion delivers 4:2:2 YUV outputs into separate chroma and luma data paths. The chroma path will be discussed here. The chroma output of the Video Input Formatter is directed to a chroma low pass 19-tap FIR filter. The filter bandwidth is selected or the filter may be bypassed via the CONTROL_1 register. The passband of the filter is either 650 KHz or 1.3 MHz and the passband ripple is less than or equal to 0.05 dB. The stopband for the 1.3 MHz selection begins at 3 MHz with an attenuation of greater that 35 dB. The stopband for the 650 KHz selection begins around 1.1 MHz with an attenuation of greater than 20 dB. 12 CS4952/53 Digital to Analog Converters The CS4952/3 provides four complete simultaneous 27 MHz DACs for analog video output: one 9-bit for S-video chrominance, one 9-bit for S-Video luminance, and two 9-bit composite outputs. Both S-Video DACs are designed for 37.5 Ω overall loads. The two composite 9-bit DACs are not identical. One DAC is designed to drive 37.5 Ω derived from a double terminated 75 Ω circuit. The second 9-bit DAC is targeted for an on-board local video connection where single point 75 Ω termination is sufficient i.e. Ch3/4 RF modulators, video amps, muxes. The DACs can be put into tri-state mode via host addressable control register bits. Each of the four DACs has its own separate DAC enable associated with it. In the disable mode, the 9-bit DACs source or sink zero current. For lower power standby scenarios the CS4952/3 also provides power shut-off control for the DACs. Each DAC has a separate DAC shut-off associated with it. Host Interface The CS4952/3 provides a parallel 8-bit data interface for overall configuration and control. The host interface uses active low read and write strobes along with an active low address enable signal to provide microprocessor compatible read and write cycles. Indirect host addressing to the CS4952/3 internal registers is accomplished via an internal address register which is uniquely accessible via bus write cycles with the host address enable signal asserted. The CS4952/3 also provides an I2C compatible serial interface for device configuration and control. This port can operate in standard or fast (400 KHz) modes. When in I2C mode, the parallel data interface PDAT [7:0] pins may be used as a general purpose I/O port controlled by the I2C interface. Closed Caption Services The CS4952/3 supports the generation of NTSC Closed Caption services. Line 21 and Line 284 captioning can be generated and enabled independently via a set of control registers. When enabled, clock run-in, start bit, and data bytes are automatically inserted at the appropriate video lines. A convenient interrupt interface simplifies the software interface between the host processor and the CS4952/3. Voltage Reference The CS4952/3 is equipped with an on-board 1.235 V voltage reference generator used by the Video DACs. For most requirements, the voltage reference output pin can be connected to the voltage reference input pin along with a decoupling capacitor. Otherwise the voltage reference input may be connected to an external voltage reference. Control Registers The control and configuration of the CS4952/3 is primarily accomplished through the control register block. All of the control registers are uniquely addressable via the internal address register. The control register bits are initialized during a chip reset. See the detailed operation section of this data sheet for all of the individual register bit allocations, bit operational descriptions and initialization states. Current Reference The DAC output current per bit is derived in the current reference block. The current step is specified by the size of resistor place between the ISET current reference pin and electrical ground. This has been optimized for 10kΩ (see “ISET” on page 25 for more informmation on selecting the proper ISET value). DS223PP2 13 CS4952/53 OPERATIONAL DESCRIPTION Reset Hierarchy The CS4952/3 is equipped with an active low asynchronous reset input pin RESET. RESET is used to initialize the internal registers and the internal state machines for subsequent default operation. See the electrical and timing specification section of this data sheet for specific CS4952/3 chip reset and power-on signaling timing requirements and restrictions. All chip outputs are valid after a time period following RESET pin low. When the RESET pin is held low, the host interface in the CS4952/3 is disabled and will not respond to host initiated bus cycles. A reset initializes the CS4952/3 internal registers to their default values as described by Table 5. In the default state, the CS4952/53 video DACs are disabled and the device is configured to internally provide blue field video data to the DACs (any input data present on the V [7:0] pins is ignored). Otherwise the CS4952/53 registers are configured for NTSC-M CCIR601 output operation. At a minimum, the DAC register (0x04) must be written (to enable the DACs) and the IN_MODE bit of the CONTROL_0 register (0x01) must be set (to enable CCIR601 data input on V [7:0]) for the CS4952/53 to become operational after RESET. Video Timing Slave Mode Input Interface In Slave Mode, the CS4952/3 takes VSYNC and HSYNC as inputs. Slave Mode is the default following a reset and is changed to Master Mode via a contol register bit (CONTROL_0 [4]). The CS4952/3 is limited to CCIR601 horizontal and vertical input timing. All clocking in the CS4952/3 is generated from the CLK pin. In Slave Mode the Sync Generator uses externally provided horizontal and vertical sync signals to synchronize the internal timing of the CS4952/3. Video data that is sent to the CS4952/3 must be synchronized to the horizontal and vertical sync signals. Figure 6 illustrates horizontal timing for CCIR601 input in Slave Mode. Note that the CS4952/3 expects to receive the first active pixel data on clock cycle 245 (NTSC) when bit SYNC_DLY=0 in the CONTROL_2 Register (Ox02). When SYNC_DLY=1, it expects the first active pixel data on clock cycle 246 (NTSC). Master Mode Input Interface The CS4952/3 defaults to Slave Mode following RESET high but may be switched into Master Mode via the MSTR bit in the CONTROL_0 Register (0x00). In Master Mode, the CS4952/3 uses the VSYNC, HSYNC and FIELD device pins as 1 1 2 2 3 3 ••• ••• 128 128 129 129 ••• ••• 244 264 245 265 246 266 247 267 248 268 NTSC 27MHz Clock Count PAL 27MHz Clock Count CLK 1682 1683 1684 1685 1686 1702 1703 1704 1705 1706 ••• ••• 1716 1728 HSYNC* (input) V[7:0] (SYNC_DLY=0) Y ••• Cr Y horizontal blanking Cb Y Cr Y active pixel #720 Y Cr Y active pixel #1 Cb active pixel #2 Y Cr active pixel #2 V[7:0] (SYNC_DLY=1) Cb active pixel #719 active pixel #720 horizontal blanking active pixel #1 Figure 6. CCIR601 Input Slave Mode Horizontal Timing 14 DS223PP2 CS4952/53 outputs to schedule the proper external delivery of digital video into the V [7:0] pins. Figure 7 illustrates horizontal timing for CCIR601 input in Master Mode. Note that the CS4952/3 expects to receive the first active pixel data on clock cycle 245 (NTSC) when bit SYNC_DLY=0 in the CONTROL_2 Register (0x02). When SYNC_DLY=1, it expects the first active pixel data on clock cycle 246 (NTSC). specifies active line numbers for both NTSC and PAL. Refer to Figure 8 for HSYNC, VSYNC and FIELD signal timing. MODE NTSC PAL NTSC Progressive-Scan PAL Progressive-Scan FIELD 1, 3 2, 4 1, 3, 5, 7 2, 4, 6, 8 NA NA ACTIVE LINES 22-261 285-524 23-310 336-623 22-261 23-310 Vertical Timing The CS4952/3 can be selected through the CONTROL_0 register (0x00) to operate in four different timing modes: PAL which is 625 vertical lines 25 frames per second interlaced, NTSC which is 525 vertical lines 30 frames per second interlaced and both PAL and NTSC again but in Progressive Scan where the display is non-interlaced. The CS4952/3 conforms to standard digital decompression dimensions and does not process digital input data for the active analog video half lines as they are typically in the over/underscan region of televisions. For NTSC, 240 active lines total per field are processed and for PAL 288 active lines total per field. Frame vertical dimensions are 480 lines for NTSC and 576 lines for PAL. Table 1 Table 1. Vertical Timing Horizontal Timing HSYNC is used to synchronize the horizontal input to output timing in order to provide proper horizontal alignment. HSYNC defaults to an input pin following RESET but switches to output in Master Mode (CONTROL_0 [4] = 1). Horizontal timing is referenced to HSYNC transitioning low. For active video lines, digital video input is to be applied to the V [7:0] inputs 244 (NTSC) or 264 (PAL), CLK periods following HSYNC going low to determine the horizontal alignment of the active video. NTSC 27MHz Clock Count PAL 27MHz Clock Count CLK 1682 1683 1684 1685 1686 1702 1703 1704 1705 1706 ••• ••• 1716 1728 1 1 2 2 3 3 ••• ••• 128 128 129 129 ••• ••• 244 264 245 265 246 266 247 267 248 268 HSYNC* (output) CB* (output) V[7:0] (SYNC_DLY=0) Y ••• Cr Y horizontal blanking Cb Y Cr Y active pixel #720 Y Cr Y active pixel #1 Cb active pixel #2 Y Cr active pixel #2 V[7:0] (SYNC_DLY=1) Cb active pixel #719 active pixel #720 horizontal blanking active pixel #1 Figure 7. CCIR601 Input Master Mode Horizontal Timing DS223PP2 15 CS4952/53 NTSC Vertical Timing (odd field) Line HSYNC* VSYNC* FIELD 3 4 5 6 7 8 9 10 NTSC Vertical Timing (even field) Line HSYNC* VSYNC* FIELD PAL Vertical Timing (odd field) Line HSYNC* VSYNC* FIELD PAL Vertical Timing (even field) Line HSYNC* VSYNC* FIELD 311 312 313 314 315 316 317 318 265 1 2 3 4 5 6 7 264 265 266 267 268 269 270 271 Figure 8. Vertical Timing 16 DS223PP2 CS4952/53 NTSC Interlaced The CS4952/3 supports NTSC-M and PAL-M modes where there are 525 total lines per frame and two fixed 262.5 line fields per frame and 30 total frames occuring per second. Please reference Figure 9 for NTSC interlaced vertical timing. Each field consists of 1 line for closed caption, 240 active lines of video plus 21.5 lines of blanking. VSYNC field one transistions low at the beginning of line 4 and will remain low for 3 lines or (858 x 3) 2574 pixel cycles. The CS4952/3 exclusively reserves line 21 of field one for closed caption insertion. Digital video input is expected to be delivered to the CS4952/3 V [7:0] pins for 240 lines beginning on active video lines 22 and continuing through line 261. VSYNC field two transistions low in the middle of line 266 and stays low for 3 lines times and transitions high in the middle of line 269. The CS4952/3 exclusively reserves line 284 of field two for closed caption insertion. Video input on the V [7:0] pins is expected between lines 285 through line 525. PAL Interlaced The CS4952/3 supports PAL modes B, D, G, H, I, N, and Combination N where there are 625 total lines per frame and two fixed 312.5 line fields per frame and 25 total frames occuring per second. Please reference Figure 10 for PAL interlaced vertical timing. Each field consists of 288 active lines of video plus 24.5 lines of blanking. Analog Field 1 VSYNC* Drops 523 524 525 1 2 3 4 5 6 7 8 9 10 22 Analog Field 2 261 262 263 264 265 266 267 268 269 270 271 272 284 285 Analog Field 3 VSYNC* Drops 523 524 525 1 2 3 4 5 6 7 8 9 10 22 Analog Field 4 261 262 263 264 265 266 267 268 269 270 271 272 284 285 Burst begins with positive half-cycle Burst begins with negative half-cycle Figure 9. NTSC Video Interlaced Timming DS223PP2 17 CS4952/53 VSYNC* Drops Analog Field 1 620 621 622 623 624 625 1 Analog Field 2 2 3 4 5 6 7 23 24 308 309 310 311 312 313 314 Analog Field 3 315 316 317 318 319 320 336 337 620 621 622 623 624 625 1 Analog Field 4 2 3 4 5 6 7 23 24 308 309 310 311 312 313 314 315 316 317 318 319 320 336 337 Analog Field 5 620 621 622 623 624 625 1 Analog Field 6 2 3 4 5 6 7 23 24 308 309 310 311 312 313 314 Analog Field 7 315 316 317 318 319 320 336 337 620 621 622 623 624 625 1 Analog Field 8 2 3 4 5 6 7 23 24 308 309 310 311 312 313 314 315 316 317 318 319 320 336 337 Burst Phase = 135 degrees relative to U Burst Phase = 225 degrees relative to U Figure 10. PAL Video Interlaced Timing 18 DS223PP2 CS4952/53 VSYNC will transition low to begin field one and will remain low for 2.5 lines or (864 x 2.5) 2160 pixel cycles. Digital video input is expected to be delivered to the CS4952/3 V [7:0] pins for 287 lines beginning on active video line 24 and continuing through line 310. Field two begins with VSYNC transitioning low after 312.5 lines from the beginning of field one. VSYNC stays low for 2.5 lines times and transitions high with the beginning of line 315. Video input on the V [7:0] pins is expected between line 336 through line 622. VSYNC stays low for 2.5 line times and transitions high during the middle of line 315. Video input on the V [7:0] pins is expected between line 335 through line 622. Field two is 313 lines long while field one is 312. NTSC Progressive Scan VSYNC will transition low at line 4 to begin field one and will remain low for 3 lines or (858 x 3) 2574 pixel times. Please reference Figure 12 for NTSC interlaced timing. Digital video input is expected to be delivered to the CS4952/3 V [7:0] pins for 240 lines beginning on active video line 22 and continuing through line 261. Field two begins with VSYNC transitioning low at line 266. VSYNC stays low for 2.5 line times and transitions high during the middle of line 268. Video input on the V [7:0] pins is expected between line 284 through line 524. Field two is 263 lines long while field one is 262. Progressive Scan The CS4952/3 supports a progessive scan mode where the video output is non-interlaced. This is accomplished by displaying only the first video field for NTSC or PAL. To preserve exact MPEG-2 frame rates of 30 and 25 per second, the CS4952/3 displays the same first field repetitively but alternately varies the field times. Other digital video encoders commonly support progressive scan by repetitively displaying a 262 line field (524/525 lines for NTSC). In the long run this method is flawed in that over time, the output display rate will overrun a system clock locked MPEG-2 decompressor and display a field twice every 8.75 seconds. CCIR-656 The CS4952/3 supports an additional Slave Mode feature that is selectable through the CCIR601 bit of the CONTROL_0 register. The CCIR-656 slave feature is unique because the horizontal and vertical timing and digital video are combined into a single 8-bit 27 MHz input. With CCIR-656 there are no horizontal and vertical input or output strobes, only 8-bit 27 MHz active CbYCrY data with start and end of video codes being implemented with reserved 00 and FF code sequences within the video feed. As with all modes, V [7:0] are sampled with the rising edge of CLK. The CS4952/3 expects the digital CCIR-656 stream to be error free. The FIELD output toggles as with non CCIR-656 input. CCIR-656 input timing is illustrated in Figure 13. PAL Progressive Scan VSYNC will transistion low to begin field one and will remain low for for 2.5 lines or (864 x 2.5) 2160 pixel times. Please reference Figure 11 for PAL non-interlaced timing. Digital video input is expected to be delivered to the CS4952/3 V [7:0] pins for 288 lines beginning on active video line 23 and continuing through line 309. Field two begins with VSYNC transitioning low after 312 lines from the beginning of field one. DS223PP2 19 CS4952/53 VSYNC* Drops Analog Field 1 309 310 311 312 313 1 Analog Field 2 2 3 4 5 6 7 23 24 308 309 310 311 312 1 2 3 4 5 6 7 23 24 Analog Field 3 309 310 311 312 313 1 Analog Field 4 2 3 4 5 6 7 23 24 308 309 310 311 312 1 2 3 4 5 6 7 23 24 Burst Phase = 135 degrees relative to U Burst Phase = 225 degrees relative to U Figure 11. PAL Video Non-Interlaced Progressive Scan Timing 20 DS223PP2 CS4952/53 Start of VSYNC Field 1 262 263 1 2 3 4 5 6 7 8 9 10 22 Field 2 261 262 1 2 3 4 5 6 7 8 9 10 22 Start of VSYNC Field 3 262 263 1 2 3 4 5 6 7 8 9 10 22 Field 4 261 262 1 2 3 4 5 6 7 8 9 10 22 Burst begins with positive half-cycle Burst phase = reference phase = 180 0 relative to B-Y Burst begins with negative half-cycle Burst phase = reference phase = 180 0 relative to B-Y Figure 12. NTSC Video Non-Interlaced Progressive Scan Timing Composite Video CCIR656 V[7:0] DATA Y Cr Y FF 00 00 XY 80 10 80 10 EAV Code 4 Clocks 80 10 80 10 80 10 Ancilliary Data 268 Clocks (NTSC) 280 Clocks (PAL) Horizontal Blanking 80 10 80 10 FF 00 00 XY Cb Y Cr Cb Y Cr SAV Code 4 Clocks 1440 Clocks Active Video Active Video Figure 13. CCIR656 Input Mode Timing DS223PP2 21 CS4952/53 Address 0x00 0x01 0x10 0x11 0x12 0x13 0x14 Register CONTROL_0 CONTROL_1 SC_AMP SC_SYNTH0 SC_SYNTH1 SC_SYNTH2 SC_SYNTH3 NTSC-MC CIR601 01h 04h 1Ch 3Eh F8h E0h 43h NTSC-MCCI R60 NTSC-MR (Japan) S170A 01h 21h 00h 04h 1Ch 1Ch 3Eh 3Eh F8h F8h E0h E0h 43h 43h PAL-B,D, G,H,I 41h 04h 15h 96h 15h 13h 54h PAL-M 61h 04h 15h 4Eh 4Ah E1h 43h PAL-N A1h 04h 15h 96h 15h 13h 54h PAL-NCom (Argentina) 81h 04h 15h 8Ch 28h EDh 43h Table 2. Multi-standard Format Register Configurations (Slave Mode, interlaced timing, non-656 data) Digital Video Input Modes The CS4952/3 provides 2 different digital video input modes that are selectable through the IN_MODE bit of the CONTROL_0 register. In mode 0 and upon RESET, the CS4952/3 defaults to output a solid color (1 of a possible of 256 colors). The background color is selected by writing the BKG_COLOR register (0x08). The colorspace of the register is RGB 3:3:2 and is unaffected by gamma correction. The default color following RESET is blue. In mode 1 the CS4952/3 supports a single 8-bit 27 MHz CbYCrY source as input on the V [7:0] pins. Input video timing can be CCIR601 master or slave and progressive scan. Output formats are configured by writing control registers as shown in Table 2. Subcarrier Generation The CS4952/3 automatically synthesizes NTSC and PAL color subcarrier clocks using the CLK frequency and four control registers (SC_SYNTH0/1/2/3). The NTSC subcarrier synthesizer is reset every four fields and every eight fields for PAL. The SC_SYNTH0/1/2/3 registers used together provide a 32-bit value which defaults to NTSC values of 43E0F83Eh following reset. Table 3 indicates the 32-bit value required for the different broadcast formats. Multi-standard Output Format Modes The CS4952/53 supports a wide range of output formats compatible with worldwide broadcast standards. These formats include NTSC-M, PAL-B/D/G/H/I, PAL-M, PAL-N and PAL Combination N (PAL-Nc) which is the broadcast standard used in Argentina. After RESET, the CS4952/53 defaults to NTSC-M operation with CCIR601 analog timing. NTSC-M can also be supported in the Japanese format by turning off the 7.5 IRE pedestal through the PED bit in the CONTROL_1 register (0x01). 22 Subcarrier Compensation Since the subcarrier is synthesized from CLK the subcarrier frequency error will track the clock frequency error. If the input clock has a tolerance of 200 ppm then the resulting subcarrier will also have a tolerance of 200 ppm. Per the NTSC specification the final subcarrier tolerance is ±10 Hz which is more like 3 ppm. Care must be taken in selecting a suitable clock source. In MPEG-2 system environments the clock is actually recovered from the data stream. In these cases the recovered clock can be 27 MHz ±50 ppm or DS223PP2 CS4952/53 System NTSC-M PAL-B, D, G, H, I, N PAL-N (Argentina) PAL-M Fsubcarrier 3.5795455 MHz 4.43361875 MHz 3.582056 MHz 3.579611 MHz Value (dec) 1138817086 1410536854 1139615885 1138838095 Value (hex) 43E0F83E 54131596 43ED288D 43CDDFC7 Table 3. Multi-standard Format FSC Register Configurations ±1350 Hz. It varies per television but in many cases given an MPEG-2 system clock of 27 MHz ±1350 Hz the resultant color subcarrier produced will be outside of the televisions ability to compensate and the chrominance information will not be displayed (black and white picture only). The CS4952/3 is designed to provide automatic compensation for an excessively inaccurate MPEG-2 system clock. Sub-carrier compensation is enabled through the XTAL bit of the CONTROL_2 register. When enabled the CS4952/3 will utilize a common quartz color burst crystal (3.579545 MHz ±50 ppm for NTSC) attached to the ADDR and XTAL pins to automatically compare and compensate the color subcarrier synthesis process. Use of the ADDR and XTAL pins requires that the host interface is configured for I2C operation. & CC_284_2 for line 284). Interrupts are also provided to simplify the handshake between the driver software and the chip. Typically the host would write all 4 bytes to be inserted into the registers and then enable closed caption insertion and interrupts. As the closed caption interrupts occur the host software would respond by writing the next two bytes to be inserted to the correct control registers and then clear the interrupt and wait for the next field. Color Bar Generator The CS4952/3 is equipped with a color bar generator that is enabled through the CBAR bit of the CONTROL_1 register. The color bar generator works in Master or Slave Mode and has no effect on the video input/output timing. If the CS4952/3 is configured for Slave Mode color bars, proper video timing must be present on the HSYNC and VSYNC pins for the color bars to be displayed. Given proper Slave Mode input timing or Master Mode, the color bar generator will override the video input pixel data. The output of the color bar generator is instantiated after the chroma interpolation filter and before the luma delay line. The generated color bar numbers are for 100% amplitude, 100% saturation NTSC EIA color bars or 100% amplitude, 100% saturation PAL EBU color bars. For PAL color bars, the CS4952/3 generates NTSC color bar values, which are very close to standard PAL values. The exact luma and chroma values are listed in Table 4. Closed Caption Insertion The CS4952/3 is capable of NTSC Closed Caption insertion on lines 21 and 284 independently. Closed captioning is enabled for either or both lines 21 & 284 via the CC_EN [1:0] register bits and data to be inserted is also written into the four Closed Caption Data registers. The CS4952/3 when enabled automatically generates the seven cycles of clock run-in (32 x line rate), start bit insertion (001)and finally insertion of the two data bytes per line. Data low at the video outputs corresponds to 0 IRE and data high corresponds to 50 IRE. There are two independent 8-bit registers per line (CC_21_1 & CC_21_2 for line 21 and CC_284_1 DS223PP2 23 CS4952/53 GPIO_CTRL_REG [7:0] bits are cleared. In GPIO input mode, the CS4952/53 will latch the data on the PDAT [7:0] pins into the corresponding bit locations of GPIO_DATA_REG when it detects register address 0x0A through the I2C interface. A detection of address 0x0A can happen in two ways. The first and most common way this will happen is when address 0x0A is written to the CS4952/53 via its I2C interface. The second method for detecting address 0x0A is implemented by accessing register address 0x09 through I2C. In I2C host interface operation, the CS4952/53 register address pointer will auto-increment to address 0x0A after an address 0x09 access. The GPIO port PDAT [7:0] pins are configured for output operation when the corresponding GPIO_CTRL_REG [7:0] bits are set. In GPIO output mode, the CS4952/53 will output the data in GPIO_DATA_REG [7:0] bit locations onto the corresponding PDAT [7:0] pins when it detects a register address 0x0A through the I2C interface. COLOR White Yellow Cyan Green Magenta Red Blue Black Cb 0 -84 +28 -56 +56 -28 +84 0 Cr 0 +14 -84 -70 +70 +84 -14 0 Y +180 +162 +131 +112 +84 +69 +35 +16 Table 4. Internal Color Bar Values (8-bit values, Cb/Cr are in 2’s complement format) Interrupts In order to better support precise video mode switches and to establish a software/hardware handshake with the closed caption insertion block the CS4952/3 is equipped with an interrupt pin named INT. The INT pin is active high. There are three interrupt sources: VSYNC, Line 21 and Line 284. Each interrupt can be individually disabled with the INT_EN register. Each interrupt is also cleared via writing a one to the corresponding INT_CLR register bits. The three individual interrupts are ORed together to generate an interrupt signal which is presented on the INT output pin. If an interrupt has occurred, it cannot be eliminated with a disable, it must be cleared. ANALOG Analog Timing All CS4952/3 analog timing and sequencing is derived from the 27 MHz clock input. The analog outputs are controlled internally by the video timing generator in conjunction with master and slave timing. The video output signals perform accordingly for NTSC, PAL specifications and both modes again but with progressive scan non-interlaced video output. Being that the CS4952/3 is almost entirely a digital circuit, great care has been taken to guarantee analog timing and slew rate performance as specified in the NTSC and PAL analog specifications. Reference the Analog Parameters section of this data sheet for exact performance parameters. General Purpose I/O Port The CS4952/53 has a GPIO port and register which is available when the device is configured for I2C host interface operation. In I2C host interface mode, the PDAT [7:0] pins are unused by the host interface and they may operate independently as input or output pins for the GPIO_DATA_REG register (0x0A). The CS4952/53 also contains the GPIO_CTRL_REG Register (0x09) which is used to configure the GPIO pins for input or output operation. The GPIO port PDAT [7:0] pins are configured for input operation when the corresponding 24 DS223PP2 CS4952/53 VREF The CS4952/3 can operate with or without the aid of an external voltage reference. The CS4952/3 is designed with an internal voltage reference generator that provides a VREFOUT signal. The internal voltage reference is utilized by electrically connecting the VREFOUT and VREFIN pins. VREFIN can also be connected to an external precision 1.235 volt reference. In either case, VREFIN is to be decoupled to ground with a 0.1 µF capacitor. Decoupling should be applied as close to the device pin as possible. DACs The CS4952/3 is equipped with 4 independent video grade current output digital to analog converters. They are 9-bit DACs operating at a 27 MHz two times oversampling rate. All four DACs are disabled and put in a low power mode upon RESET. All four DACs can be individually powered down and disabled. The output current per bit of all four DACs is determined by the size of resistor connected between the ISET pin and electrical ground. Luminance DAC The Y pin is driven from a 9-bit 27 MHz current output DAC that internally receives the Y or luminance portion of the video signal (black and white intensity and syncronization information only). Y is designed to drive proper video levels into a 37.5 Ω load. Reference the detailed electrical section of this data sheet for the exact Y digital to analog AC and DC performance data. A Y_EN enable control bit in the DAC register (0x08) is provided to enable or disable the luminance DAC. For a complete disable and lower power operation the Luminance DAC can be totally shut down via the Y_PD control bit in the DAC register (0x08). In this mode turn-on through the control register will not be instantaneous. ISET All four of the CS4952/3 digital to analog converter DACs are output current normalized with a common ISET device pin. The DAC output current per bit is determined by the size of the resistor connected between ISET and electrical ground. Typically a 10 kΩ±1% metal film resistor should be used. The ISET resistance can be changed by the user to accommodate varying video output attenuation via post filters and also to suit individual preferred performance. In conjunction with the ISET value, the user may also independently vary the chroma, luma and colorburst amplitude levels via host addressable control register bits that are used to control internal digital amplifiers. The DAC output levels are defined by the following operations: VREFIN/RISET = IREF 1.235 V/10 kΩ = 123.5 µA CVBS37/Y/C Outputs: VOUT (max) = IREF × (8/15) × 511 × 37.5 Ω = 1.262 V CVBS75 Output: VOUT (max) = IREF × (4/15) × 511 × 75 Ω = 1.262 V Chrominance DAC The C pin is driven from a 9-bit 27 MHz current output DAC that internally receives the C or chrominance portion of the video signal (color only). C is designed to drive proper video levels into a 37.5 Ω load. Reference the detailed electrical section of this data sheet for the exact C digital to analog AC and DC performance data. A C_EN enable control register bit in the DAC register (0x08) is provided to enable or disable the Chrominance DAC. For a complete disable and lower power operation the Chrominance DAC can be totally shut down via the C_PD control register bit in the DAC DS223PP2 25 CS4952/53 register (0x08). In this mode turn-on through the control register will not be instantaneous. CVBS37 DAC The CVBS37 pin is driven from a 9-bit 27 MHz current output DAC that internally receives a combined luma and chroma signal to provide composite video output. CVBS37 is designed to drive proper composite video levels into a 37.5 Ω load. Reference the detailed electrical section of this data sheet for the exact CVBS37 digital to analog AC and DC performance data. The C_37_EN DAC enable control register bit is in the DAC register (0x08) provided to enable or disable the ouput pin. When disabled, no current flow from the output. For a complete disable and lower power operation the CVBS37 DAC can be totally shut down via the C_37_PD control register bit in the DAC register (0x08). In this mode turn-on through the control register will not be instantaneous. CVBS75 DAC The CVBS75 pin is driven from a 9-bit 27 MHz current output DAC that internally receives a combined luma and chroma signal to provide composite video output. CVBS75 is designed to drive proper composite video levels into a 75 Ω load. Reference the detailed electrical section of this data sheet for the exact CVBS75 digital to analog AC and DC performance data. A C_75_EN enable control register bit in the DAC register (0x08) is provided to enable or disable the ouput pin. When disabled, no current flows from the output. For a complete disable and lower power operation the CVBS75 DAC can be totally shut down via the C_75_PD control register bit in the DAC register (0x08). In this mode turn-on through the control register will not be instantaneous. 26 DS223PP2 CS4952/53 PROGRAMMING Host Control Interface The CS4952/3 host control interface can be configured for I2C or 8-bit parallel operation. The CS4952/3 will default to I2C operation when the RD and WR pins are both tied low at power up. The RD and WR pins are active for 8-bit parallel operation only. The I2C bus address for the CS4952/3 is programmable via register I2C_ADR (0x0F). 8-bit Parallel Interface The CS4952/3 is equipped with a full 8-bit parallel microprocessor write and read control port. Along with the PDAT [7:0] pins the control port interface is comprised of host read RD and host write WR active low strobes and host address enable ADDR which, when low, enables unique address register accesses. The control port is used to access internal registers which configure the CS4952/3 for various modes of operation. The internal registers are uniquely addressed via an address register. The address register is accessed during a host write cycle with the WR and ADDR pins set low. Host write cycles with ADDR set high will write the 8-bits on the PDAT [7:0] pins into the register currently selected by the address register. Likewise read cycles occur with RD set low and ADDR set high will return the register contents selected by the address register. Reference the detailed electrical timing parameter section of this data sheet for exact host parallel interface timing characteristics and specifications. When I2C interface operation is being used, RD and WR must be tied to ground. PDAT [7:0] are available to be used for GPIO operation in I2C host interface mode. I2C Interface The CS4952/3 provides an I2C interface for accessing the internal control and status registers. External pins are a bidirectional data pin (SDA) and a serial input clock (SCL). The protocol follows the I2C specifications. A complete data transfer is shown in Figure 14. Note that this I2C interface will work in Slave Mode only - it is not a bus master. SDA and SCL are connected via an external pull-up resistor to a positive supply voltage. When the bus is free, both lines are high. The output stages of devices connected to the bus must have an open-drain or open-collector in order to perform the wired-AND function. Data on the I2C bus can be transferred at a rate of up to 400 kbits/sec in fast mode. The number of interfaces to the bus is solely dependent on the limiting bus capacitance of 400 pF. When 8-bit parallel interface operation is being used, SDA and SCL can be tied directly to ground. I 2 C Protocol SDA SCL A Start 1-7 8 Address R/W 9 ACK 1-7 8 9 ACK 1-7 8 9 ACK P Stop Data Data Note: I 2 C transfers data always with MSB first, LSB last Figure 14. I2C Data Transfer DS223PP2 27 CS4952/53 Register Description A set of internal registers are available for controlling the operation of the CS4952/3. The registers extend from internal address 0x00 through 0x3D. Table 5 shows a complete list of these registers and Address 0x00 0x01 0x02 0x03 0x04 0x05 - 0x06 0x07 0x08 0x09 0x0A 0x0B - 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D - 0x3A 0x3B 0x3C 0x3D Register Name CONTROL_0 CONTROL_1 CONTROL_2 RESERVED DAC RESERVED STATUS BKG_COLOR GPIO_CTRL_REG GPIO_DATA_REG RESERVED C_AMP Y_AMP I2C_ADR SC_AMP SC_SYNTH0 SC_SYNTH1 SC_SYNTH2 SC_SYNTH3 HUE_LSB HUE_MSB RESERVED CC_EN CC_21_1 CC_21_2 CC_284_1 CC_284_2 RESERVED INT_EN INT_CLR ID_REG their internal addresses. Note that this table and the subsequent register description section describe the full register map for CS4952 only. A complete CS4953 register set description is only available to Macrovision ACP-PPV Licensed Buyers. Type r/w r/w r/w r/w read only r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w r/w read only Default Value 01h 04h 00h F0h 00h 03h 00h 80h 80h n/a 1Ch 3Eh F8h E0h 43h 00h 00h 00h 00h 00h 00h 00h 00h 00h n/a Table 5. Control Register Map 28 DS223PP2 CS4952/53 Control Register 0 Address Bit Number Bit Name Default Bit 7:5 0x00 7 0 Mnemonic TV_FMT CONTROL_0 6 TV_FMT 0 5 0 4 MSTR 0 Read/Write 3 CCIR656 0 2 PROG 0 Default Value = 01h 1 0 IN_MODE CBCR_UV 0 1 4 3 2 1 0 MSTR CCIR656 PROG IN_MODE CBCR_UV Function selects the TV display format 000: NTSC-M CCIR601 timing (default) 001: NTSC-M RS170A timing 010: PAL-B, D, G, H, I 011: PAL-M 100: PAL-N (Argentina) 101: PAL-N (non Argentina) 110-111: reserved 1: Master Mode, 0: Slave Mode video input is in CCIR656 format (0: off, 1: on) Progressive scanning enable (enable with 1) Input select (0: solid background, 1: use V [7:0] data) enable YCbCr to YUV conversion (1: enable, 0: disable) Control Register 1 Address Bit Number Bit Name Default Bit 7 6 5 4 3 2 1 0 0x01 7 CBLANK 0 Mnemonic CBLANK Y_DELAY C_BW C_LPF_EN FLD PED CBAR CBCRSEL CONTROL_1 6 Y_DELAY 0 5 C_BW 0 4 C_LPF_EN 0 Read/Write 3 FLD 0 2 PED 1 Default Value = 04h 1 CBAR 0 0 CBCRSEL 0 Function Composite Blank / HSYNC output select (1: CB, 0: HSYNC) luma to chroma delay (0: no delay, 1: luma is delayed by one 13.5 MHz cycle) chroma lpf bandwidth (0: 650 KHz, 1: 1.3 MHz) chroma lpf on/off (0: off, 1: on) Polarity of Field (0: odd field - 0, 1: odd field - 1) Pedestal offset (0: 0 IRE, 1: 7.5 IRE) internal color bar generator (0: off, 1: on) CbCr select (0: chroma undelayed, 1: chroma delayed by one clock) DS223PP2 29 CS4952/53 Control Register 2 Address Bit Number Bit Name Default Bit 7:4 3 0x02 7 0 Mnemonic Y_BW 6 0 CONTROL_2 5 RESERVED 0 4 0 Read/Write 3 0 Default Value = 00h 2 SYNC_DLY 0 1 XTAL 0 0 SC_EN 0 2 1 0 SYNC_DLY XTAL SC_EN Function reserved Selects between 4.2 Mhz and 6 Mhz on-chip luminance low pass filters; default value is zero which selects the 4.2 Mhz low pass filter option Delays expected timing of first active pixel input data relative to falling edge of HSYNC from 245 27 MHz clock cycles to 246 for NTSC and from 265 to 266 for PAL. Default State is SYNC_DLY=0 for no delay Crystal oscillator for subcarrier adjustment enable (1: enable) Chroma burst disable (1: disable) DAC Power Down Register Address Bit Number Bit Name Default Bit 7 6 5 4 3 2 1 0 0x04 7 C_75_PD 1 Mnemonic C_75_PD C_37_PD Y_PD C_PD C_75_EN C_37_EN Y_EN C_EN DAC 6 C_37_PD 1 5 Y_PD 1 4 C_PD 1 Read/Write 3 C_75_EN 0 Default Value = F0h 2 C_37_EN 0 1 Y_EN 0 0 C_EN 0 Function power down composite DAC with 75 Ω load (0: power up, 1: power down) power down composite DAC with 37.5 Ω load (0: power up, 1: power down) power down luma s-video DAC (0: power up, 1: power down) power down chroma s-video DAC (0: power up, 1: power down) enable composite video DAC output for 75 Ω (0: tri-state, 1: enable) enable composite video DAC output for 37.5 Ω (0: tri-state, 1: enable) enable s-video DAC for luma output (0: tri-state, 1: enable) enable s-video DAC for chroma output (0: tri-state, 1: enable) 30 DS223PP2 CS4952/53 Status Register Address Bit Number Bit Name Default Bit 7:6 5 4 3 2:0 0x07 7 6 RESERVED 0 0 Mnemonic CC_INT_21 CC_INT_284 VS_INT FIELD STATUS 5 CC_INT_21 0 Read Only 4 CC_INT_284 0 3 VS_INT 0 Default Value = 00h 2 0 1 FIELD 0 0 0 Function reserved Interrupt flag for line 21 (closed caption) complete Interrupt flag for line 284 (closed caption) complete Interrupt flag for video field change Field Status bits 000: field 8 001: field 1 010: field 2 011: field 3 100: field 4 101: field 5 110: field 6 111: field 7 Background Color Register Address Bit Number Bit Name Default Bit 7:0 0x08 7 0 Mnemonic BG_COLR 6 0 BKG_COLOR 5 0 4 Read/Write 3 BG_COLR 0 0 0 2 Default Value = 03h 1 1 0 1 Function Background color (7:5 = R, 4:2 = G, 1:0 = B) GPIO Control Register Address Bit Number Bit Name Default Bit 7:0 0x09 7 0 Mnemonic GPIO_IO 6 0 GPIO_CTRL_REG 5 0 4 Read/Write 3 GPIO_IO 0 0 0 2 Default Value = 00h 1 0 0 0 Function input(0)/output(1) control of GPIO registers (bit X: PDAT(X) I/O configuration) DS223PP2 31 CS4952/53 GPIO Data Register Address Bit Number Bit Name Default Bit 7:0 0x0A 7 0 Mnemonic GPIO_DATA 6 0 GPIO_DATA_REG 5 0 Read/Write 4 3 GPIO_DATA 0 0 2 0 Default Value = 00h 1 0 0 0 Function GPIO data register; data is output on PDAT [7:0] bus if appropriate bit in GPIO_CTRL_REG (0x09) is set to “1”; data on PDAT [7:0] is latched into GPIO_DATA_REG [7:0] when register address 0x0A is accessed via I2C. This register is only accessible in I2C mode. Chroma Filter Register Address Bit Number Bit Name Default Bit 7:0 0x0D 7 1 Mnemonic C_COEF 6 0 C_AMP 5 0 4 Read/Write 3 C_COEF 0 0 Function 0 2 Default Value = 80h 1 0 0 0 Chroma amplitude coefficient Luma Filter Register Address Bit Number Bit Name Default Bit 7:0 0x0E 7 1 Mnemonic Y_COEF 6 0 Y_AMP 5 0 4 Read/Write 3 Y_COEF 0 0 Function 0 2 Default Value = 80h 1 0 0 0 Luma amplitude coefficient I2C Address Register Address Bit Number Bit Name Default Bit 7 6:0 0x0F 7 RESERVED Mnemonic ADDR 6 - I2C_ADR 5 4 - Read/Write 3 ADDR Function 2 - Default Value = N/A 1 0 - reserved I2C device address (programmable) 32 DS223PP2 CS4952/53 Subcarrier Amplitude Register Address Bit Number Bit Name Default Bit 7:0 0x10 7 0 Mnemonic AMP 6 0 SC_AMP 5 0 4 Read/Write 3 AMP 1 1 Function 1 2 Default Value = 1Ch 1 0 0 0 Color burst amplitude Subcarrier Synthesis Register Address 0x11 0x12 0x13 0x14 Bits 7:0 7:0 7:0 7:0 SC_SYNTH0 SC_SYNTH1 SC_SYNTH2 SC_SYNTH3 Mnemonic - Read/Write Default Value = 3Eh F8h E0h 43h Register SC_SYNTH0 SC_SYNTH1 SC_SYNTH2 SC_SYNTH3 Function Subcarrier synthesis bits 7:0 Subcarrier synthesis bits 15:8 Subcarrier synthesis bits 23:16 Subcarrier synthesis bits 31:24 Hue LSB Adjust Register Address Bit Number Bit Name Default Bit 7:0 0x15 7 0 Mnemonic LSB 6 0 HUE_LSB 5 0 4 Read/Write 3 LSB 0 0 Function 0 2 Default Value = 00h 1 0 0 0 8 LSBs for hue phase shift Hue MSB Adjust Register Address Bit Number Bit Name Default Bit 7:2 1:0 0x16 7 0 Mnemonic MSB 6 0 HUE_MSB 5 4 RESERVED 0 0 Read/Write 3 0 Function 2 0 Default Value = 00h 1 MSB 0 0 0 reserved 2 MSBs for hue phase shift DS223PP2 33 CS4952/53 Closed Caption Enable Register Address Bit Number Bit Name Default Bit 7:2 1 0 0x18 7 0 Mnemonic EN_284 EN_21 6 0 CC_EN 5 4 RESERVED 0 0 Read/Write 3 0 Function 2 0 Default Value = 00h 1 EN_284 0 0 EN_21 0 reserved enable closed caption for line 284 enable closed caption for line 21 Closed Caption Data Register Address 0x19 0x1A 0x1B 0x1C Bit 7:0 7:0 7:0 7:0 CC_21_1 CC_21_2 CC_284_1 CC_284_2 Mnemonic - Read/Write Default Value = 00h 00h 00h 00h Register CC_21_1 CC_21_2 CC_284_1 CC_284_2 Function first closed caption databyte of line 21 second closed caption databyte of line 21 first closed caption databyte of line 284 second closed caption databyte of line 284 Interrupt Enable Register Address Bit Number Bit Name Default Bit 7:3 2 1 0 0x3B 7 0 Mnemonic EN_21 EN_284 VS_EN 6 0 INT_EN 5 RESERVED 0 4 0 Read/Write 3 0 Default Value = 00h 2 EN_21 0 1 EN_284 0 0 VS_EN 0 Function reserved interrupt enable for closed caption line 21 interrupt enable for closed caption line 284 interrupt enable for new field 34 DS223PP2 CS4952/53 Interrupt Clear Register Address Bit Number Bit Name Default Bit 7:3 2 1 0 0x3C 7 0 Mnemonic CLR_21 CLR_284 VS_CLR 6 0 INT_CLR 5 RESERVED 0 4 0 Read/Write 3 0 Default Value = 00h 2 CLR_21 0 1 CLR_284 0 0 VS_CLR 0 Function reserved clear interrupt for closed caption line 21 (INT_21) clear interrupt for closed caption line 284 (INT_284) clear interrupt for new video field (INT_V) Device ID Register Address Bit Number Bit Name Default Bit 7:4 3:0 0x3D 7 0 Mnemonic DEV_ID 6 ID_REG 5 DEV_ID 0 0 0 4 Read Only 3 Function Default Value = N/A 2 1 RESERVED 0 - 0000 device ID for CS4952 0001 device ID for CS4953 These bits are reserved and the value they return on a read is not defined DS223PP2 35 CS4952/53 BOARD DESIGN & LAYOUT CONSIDERATIONS The printed circuit layout should be optimized for lowest noise on the CS4952/3 power and ground lines. Digital and analog sections should be physically separated and the CS4952/3 placed as close to the output connectors as possible. All analog supply traces should be as short as possible to minimize inductive ringing. A well designed power distribution network is essential in eliminating digital switching noise. The ground planes must provide a low-impedance return path for the digital circuits. A PC board with a minimum of four layers is recommended. The ground layer should be used as a shield to isolate noise from the analog traces. The top layer (1) should be reserved for analog traces but digital traces may share this layer if the digital signals have low edge rates and switch little current or if they are separated from the analog traces by a significant distance (dependent on their frequency content and current). The second layer should then be the ground plane followed by the analog power plane on layer three and the digital signal layer on layer four same supply. If necessary, further isolate the digital and analog power supplies by using ferrite beads on each supply branch followed by a low ESR capacitor. Place all decoupling caps as close as possible to the device as possible. Surface mount capacitors generally have lower inductance than radial lead or axial lead components. Surface mount caps should be placed on the component side of the PCB to minimize inductance caused by board vias. Any vias, especially to ground, should be as large as practical to reduce their inductive effects. VREF Decoupling The VREFOUT pin provides a 1.235 V reference for the internal DACs. VREFOUT is only intended to drive VREFIN. Do not connect to an external load. A small bypass cap, however, may be placed on VREFOUT to reduce noise. Usually a 0.1uF MLC surface mount capacitor is sufficient. Digital Interconnect The digital inputs and outputs of the CS4952/3 should be isolated from the analog outputs as much as possible. Use separate signal layers whenever possible and do not route digital signals over the analog power and ground planes. Noise from the digital section is directly related to the digital edge rates used. Ringing, overshoot, undershoot, and ground bounce are all related to edge rate. Use lower speed logic such as HCMOS for the host port interface to reduce switching noise. For the video input ports, higher speed logic is required, but use the slowest practical edge rate to reduce noise. To reduce digital noise, it is important to match the source impedance, line impedance, and load impedance as much as possible. Generally, if the line length is greater than one fourth the signal edge rate, line termination is necessary. Ringing may also be reduced by damping the line with a series resistor (22 - 150 Ω). Under extreme cases, it may DS223PP2 Power and Ground Planes The power and ground planes need isolation gaps of at 0.05” to minimize digital switching noise effects on the analog signals and components. A split analog/digital ground plane should be connected at one point as close as possible to the CS4952/3. A split analog/digital power plane should be connected at one point as close as possible to the power entry point and decoupled properly. Power Supply Decoupling Start by reducing power supply ripple and wiring harness inductance by placing a large (33 - 100uF) capacitor as close to the power entry point as possible. Use separate power planes or traces for the digital and analog sections even if they use the 36 CS4952/53 be advisable to use microstrip techniques to further reduce radiated switching noise if very fast edge rates (