CS8130-CSZR

CS8130 CS8130 Semiconductor Corporation Multi-Standard Infrared Transceiver Features General Description • Adds IR port to standard UART • IrDA, HPSIR, ASK (CW) & TV remote The CS8130 is an infrared transceiver integrated circuit. The receive channel includes on-chip high gain PIN diode amplifier, IrDA, HPSIR, ASK & TV remote compatible decoder, and data pulse stretcher. The transmit path includes IrDA, HPSIR, ASK & TV remote compatible encoder, and LED driver. The computer data port is standard UART TxD and RxD compatible, and operates from 1200 to 115200 baud. compatible • 1200bps to 115kbps data rate • Programmable Tx LED power • Programmable Rx threshold level • Power down modes • Direct, no modulation, mode • Tiny 5x7mm 20 pin SSOP package • +2.7V to +5.5V supply External PIN diode and transmit LED are required. A control mode is provided to allow easy UART programming of different modes. The CS8130 operates from power supplies of +2.7V to +5.5V. Ordering Information: See page 28. +Supply +Supply VA+ VD+ 8 PINA PINC 12 11 6 13 Threshold Detect/Decode PIN Diode Preamplifier 7 RESET RXD RxD Demodulator 16 FORM/BSY CTS +Supply LED1C 1 LED Driver 1 LED2C 4 LED Driver 2 14 Data/Control Decoder FIFO Modulator 15 3 TGND2 Baud Rate Generator 2 TGND1 5 AGND 19 EXTCLK 17 10 18 9 XTALIN XTALOUT TXD STANDARD UART TxD D/C DTR PWRDN 20 CLKFR DGND Preliminary Product Information This document contains information for a new product. Crystal Semiconductor reserves the right to modify this product without notice. Crystal Semiconductor Corporation http://www.cirrus.com P.O. Box 17847, Austin, TX 78760 (512) 445-7222 FAX: (512) 445-7581 Copyright  Crystal Copyright © Cirrus Logic, Inc. 2005 Semiconductor Corporation 1994 (All Rights Reserved) (All Rights Reserved) JUN ‘05 ’94 SEP DS134PP2 DS134F1 1 CS8130 CS8130 TRANSMITTER DRIVER CHARACTERISTICS (TA = 25 °C; All V+ = 3.0V, Digital Input Levels: Logic 0 = 0V, Logic 1 = V+; unless otherwise specified) Parameter Symbol Output capacitance (Note 1) Output rise time (10% to 90%) tr Output fall time (90% to 10%) tf Overshoot over final current On resistance Off leakage current Output current (each driver) (Note 2) Output jitter relative a jitter free input clock Notes: 1. Typical LED junction capacitance is 20pF. 2. 50% duty cycle, max pulse width 165 µs (3/16 of (1/1200 bps + Min Typ Max Units - 10 20 20 - TBD 50 50 25 0.5 20 250 200 pF ns ns % Ω µA mA ns 5%)). RECEIVER CHARACTERISTICS (TA = 25 °C; All V+ = 3.0V, Digital Input Levels: Logic 0 = 0V, Logic 1 = V+; unless otherwise specified) Parameter Symbol Min Typ Max Units Input capacitance (Note 3) 10 TBD pF Input noise current 11 pA/rtHz Maximum signal input current from detector 2 mA Maximum DC input current (typically sunlight) 200 µA Input current detection thresholds RS4-0=00000: 7.8 nA (Programmable with a 5 bit value) RS4-0=00001: 15.6 nA 16.4 23.4 30.4 nA (Min, Max = Typical ±30%) RS4-0=00010: " ↓ ↓ ↓ (Note 4) ↓ nA 169.5 242.2 314.9 RS4-0=11110: nA 175 250 325 RS4-0=11111: Bandpass filter response High Pass -3dB: 35 kHz Low Pass -3dB: 700 kHz 5 10 ms Receiver power up time With high (200µA) dc ambient 0.3 1 ms With normal (2µA) dc ambient Turn-around time, with receiver on continuously (Note 5) 5 10 ms EMI rejection of system (0.5MHz to 100MHz). (Note 6) 3 V/m Notes: 3. Typical PIN diode junction capacitance is 50pF. 4. The ±30% tolerance covers chip-to-chip variation. The temperature coefficient of the receiver threshold setting is low. Current detection thresholds are above the DC ambient condition. Settings of RS4-0 of less than 00010 are not practical because of noise. 5. Turn-around time is the time taken for the PIN diode receiver to recover from the IR energy from the transmitter. The remote end of the link must wait for this time after receiving data before transmitting a reply. This time may be reduced to 1 µs). Clock Generation Power Down The primary clock required is 3.6864 MHz. This may be generated by attaching a 3.6864 MHz crystal to the XTALIN and XTALOUT pins. In this case, the EXTCLK pin becomes an output, and may be used to drive external devices. If this is not required, power may be saved by disabling the EXTCLK output. The CLKFR pin should be connected to DGND, which causes the clock circuits to be configured for 3.6864 MHz operation. When the PWRDN pin is brought low, all internal logic is stopped, including the crystal oscillator. The power consumption in power down mode is very low (25 ms if using the crystal oscillator (see Clock Generation above). The following tables define the detailed function of all the registers inside the CS8130. Control Register Definitions The various control registers within the CS8130 may be written by setting the D/C pin to low, and sending characters from the UART to the TXD pin. The characters are interpreted as a 4bit address field and a 4-bit data field, as shown in Figure 7. After the control character is received and written into the control register, it is optionally echoed back out the RXD pin. The baud rate used for this control mode is whatever is currently set in the baud rate register. If the "load baud rate" bit is written to, then the new baud rate takes effect after the character has been echoed back, if echo is enabled. Otherwise, the new baud rate is effective immediately. One of the control registers contains a shadow register set enable bit, which effectively becomes the MSB of the 5-bit register address. Hence there are 31 4-bit registers. The shadow bit must be written to a 1 to allow access to the registers with addresses 16 through 31. The shadow bit Start Bit TXD Data CD0 CD1 CD2 Stop Bit Address CD3 AD0 AD1 AD2 AD3 D/C Start Bit RXD Data CD0 CD1 CD2 Stop Bit Address CD3 AD0 AD1 AD2 AD3 Figure 7. Control Mode Timing 12 DS134F1 DS134PP2 CS8130 CS8130 Control Data Byte Format BIT D7 D6 D5 D4 D3 D2 D1 D0 AD3 AD2 AD1 AD0 CD3 CD2 CD1 CD0 NAME AD3-0 Register Address (4 bits of transmitted address + MSB, which is the shadow (SHDW) bit state [Control Reg #3]. All registers have 4 data bits). CD3-0 Control Data VALUE 0_0000 0_0001 0_0010 0_0011 0_0100 0_0101 0_0110 0_0111 0_1000 0_1001 0_1010 0_1011 0_1100 0_1101 0_1110 0_1111 1_0000 1_0001 1_0010 1_0011 1_0100 1_0101 1_0110 1_0111 1_1000 1_1001 1_1010 1_1011 1_1100 1_1101 1_1110 1_1111 FUNCTION 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Control register #1 Control register #2 Transmit Mode Register #1 Transmit Mode Register #2 Output Power register Receive Mode register Receive Sensitivity register #1 Receive Sensitivity register #2 Baud Rate Divider register #1 Baud Rate Divider register #2 Modulator Divider register #1 Modulator Divider register #2 Digital Output Pin Control register Control Register #3 Reserved Status register (read only) TV Remote Receive Sample Rate & T Period Divider TV Remote Receive Sample Rate & T Period Divider TV Remote Receive Sample Rate & T Period Divider TV Remote Transmit Bit Rate Divider #1 TV Remote Transmit Bit Rate Divider #2 Control Register #4 Reserved Reserved ASK Receive Timing Sensitivity register Reserved Reserved Reserved CS8130 Revision Level register (Read Only) Reserved Reserved (Resets to 1111; must not be changed) Reserved (Resets to 1111; must not be changed) Contains control register data. It is essential that all reserved registers and bits are not changed from their reset state. If reserved bits are changed, then internal test modes may be invoked, which may change some input pins to output pins, and may completely change the definition of some functions and signals. Reserved bits in registers, and reserved registers, may not return a known state when read, and should be ignored. Registers 28 and 15 are read only. Other non-reserved registers are write only. The CS8130 can be set to echo back register write commands to verify correct reception of the control settings. DS134F1 DS134PP2 13 13 CS8130 CS8130 Register 0, Control Register #1 D3 D2 D1 D0 Register ECHO 0 RXEN TXEN Reset (R) 0 0 0 0 BIT ECHO RXEN NAME Echo Control Characters Receiver Enable TXEN Transmitter Enable VALUE 0 1 0 1 0 1 FUNCTION R Do not echo control characters Echo control characters. R Receiver disabled Receiver enabled R Transmitter disbabled Transmitter enabled VALUE 0 1 0 1 FUNCTION R Auto detect receive format disabled Auto detect receive format enabled R Do not load new baud rate count value Load new baud rate count value Register 1, Control Register #2 D3 D2 D1 Register 0 0 AUTD Reset (R) 0 0 0 BIT AUTD LODB NAME Receiver auto detect mode enable Load Baud Rate Counter D0 LODB 0 The LODB bit resets to 0 automatically. 14 DS134F1 DS134PP2 CS8130 CS8130 Register 2, Transmit Mode Register #1 D3 D2 D1 Register DIR TVR PWID Reset (R) 0 0 0 BIT DIR NAME Direct Mode Enable TVR TV Remote Mode Enable Select Pulse Width PWID MODU D0 MODU 0 VALUE 0 1 0 1 0 1 0 1 Select Modulation Method R R R R FUNCTION Mode 4 Direct access mode disabled Mode 4 Direct access mode enabled Mode 3 TV remote mode disabled Mode 3 TV remote mode enabled Set pulse width to 1.6 µS Set pulse width to 3/16 of the bit period Mode 1 IrDA pulse modulation enabled Mode 2 Amplitude modulated carrier modulation Register 3, Transmit Mode Register #2 D3 D2 D1 D0 Register 0 CHSY BC1 BC0 Reset (R) 0 1 1 BIT CHSY BC1-0 0 NAME Character/bit synchronized Number of bits per character (only needed if CHSY = 1) VALUE 0 1 00 01 10 11 0 1 2 3 FUNCTION Bits are transmitted based on TXD bit transitions R Bits are transmitted timed from the start bit 6 data bits per character 7 data bits per character R 8 data bits per character 9 data bits ( 8 data, 1 parity) per character 0 1 2 3 FUNCTION R No LED output enabled LED1C output only enabled LED2C output only enabled Both LED1C and LED2C outputs enabled Register 4, Output Power Register D3 D2 D1 D0 Register 0 0 OP1 OP0 Reset (R) 0 0 0 0 BIT OP1-0 DS134F1 DS134PP2 NAME Output Power Level VALUE 00 01 10 11 15 15 CS8130 CS8130 Register 5, Receive Mode Register D3 Register Reset (R) BIT RTVR, RMOD, RWIDS, RWIDL D2 D1 D0 RTVR RMOD RWIDS RWIDL 0 0 1 1 NAME Receive Mode VALUE 0000 0001 0010 0011 0100 1000 1100 FUNCTION 0 Mode 2 Amplitude modulated carrier mode 1 Mode 1a IRDA - fixed 1.6µs pulse 2 Mode 1b IRDA - variable 3/16 bit cell time pulse 3 R Mode 1c IRDA - Any width pulse from 1.6µs to 3/16 bit cell time 4 Mode 4 Direct access mode 8 Mode 3 TV remote mode, oversampling receive 12 Mode 3 TV remote mode, timed bit cell receive All other combinations are reserved Register 6, Receive Sensitivity Register #1 D3 D2 D1 D0 Register RS3 RS2 RS1 RS0 Reset (R) 0 1 1 1 Register 7, Receive Sensitivity Register #2 D3 D2 D1 D0 Register 0 0 0 RS4 Reset (R) 0 0 0 0 BIT RS4-0 NAME Receive threshold setting. VALUE 00000 00001 " 00111 " 11110 11111 FUNCTION 0 7.8 nA nominal receive threshold 1 15.6 nA nominal receive threshold " " 7 R 62.5 nA nominal receive threshold " " 30 242.2 nA nominal receive threshold 31 250 nA nominal receive threshold Threshold settings of less than 20nA should not be used because background noise will cause the apparent occurrence of constant signal. 16 DS134F1 DS134PP2 CS8130 CS8130 Register 8, Baud Rate Divider Register #1 D3 D2 D1 D0 Register BR3 BR2 BR1 BR0 Reset (R) 0 1 1 1 Register 9, Baud Rate Divider Register #2 D3 D2 D1 D0 Register BR7 BR6 BR5 BR4 Reset (R) 0 0 0 1 BIT BR7-0 NAME Baud Rate Divider Value (BRD). BRD=(3.6864E6/ (16*BR))-1, where BRD = divider value and BR = desired baud rate. VALUE 01011111 00101111 00010111 00001011 00001001 00000010 00000001 FUNCTION 95 2400 bps 47 4800 bps 23 R 9600 bps 11 19.2 kbps 5 38.4 kbps 2 76.8 kbps 1 115.2 kbps Register 10, Modulator Divider Register #1 D3 D2 D1 D0 Register MD3 MD2 MD1 MD0 Reset (R) 0 1 1 0 Register 11, Modulator Divider Register #2 D3 D2 D1 D0 Register MD7 MD6 MD5 MD4 Reset (R) 0 0 0 0 BIT MD7-0 NAME Modulator Divider Value (MD). MD=(3.6864E6/FR)1, where MD = divider value and FR = desired modulation frequency. VALUE 01100000 96 38 kHz 00000110 6 R 527kHz FUNCTION The transmitted modulation frequency will be exact. The receive carrier detection frequency can be slightly different from the programmed frequency (see Receive ASK Carrier Timing Register). DS134F1 DS134PP2 17 17 CS8130 CS8130 Register 12, Output Pin Control Register D3 Register Reset (R) BIT RXDT RXDH FORT FORH D2 RXDT RXDH 0 1 D1 FORT 0 D0 FORH 1 NAME RXD output pin three-state enable RXD output pin high/low enable FORM/BSY output pin three-state enable FORM/BSY output pin high/low enable VALUE 0 1 0 1 0 1 R In In In R In R In In 0 1 In power down, FORM/BSY will go low, if FORT = 0 R In power down, FORM/BSY will go high, if FORT = 0 VALUE 0 1 FUNCTION R Enable access to registers 0 though 15 Enable access to shadow registers (16 through 31) VALUE 0 FUNCTION Oscillator not running, using external clock input, oscillator circuit is powered down. Oscillator running, EXTCLK is an output, if enabled. R No error A framing error has occurred since the last read of this bit. Resets after read R IrDA pulse style data format detected Amplitude modulated carrier style data format detected power power power power power power down, down, down, down, down, down, FUNCTION RXD will go high or low. RXD will float. RXD will go low, if RXDT = 0 RXD will go high, if RXDT = 0 FORM/BSY will go high or low. FORM/BSY will float. Register 13, Control Register #3 D3 D2 D1 Register 0 0 0 Reset (R) 0 0 BIT SHDW 0 D0 SHDW 0 NAME Shadow register set enable Register 15, Status Register D3 D2 Register 0 OSCR Reset (R) 0 BIT OSCR D1 D0 ERR DMOD 0 0 NAME Oscillator running flag ERR Framing error flag 1 0 1 DMOD Detected Modulation Type 0 1 To read this register, write 0000 to address 15. Independent of the setting of the ECHO bit, the CS8130 will transmit the above contents, with an address field of 1111. 18 DS134F1 DS134PP2 CS8130 CS8130 Register 16, TV Remote Receive Timing Register #1 D3 Register Reset (R) D2 D1 TVR3 TVR2 TVR1 1 1 1 D0 TVR0 1 Register 17, TV Remote Receive Timing Register #2 D3 D2 Register TVR7 TVR6 Reset (R) 1 1 D1 TVR5 1 D0 TVR4 1 Register 18, TV Remote Receive Timing Register #3 D3 Register Reset (R) BIT TVR11-0 D2 TVR11 TVR10 0 1 D1 TVR9 1 NAME TV remote mode receiver timing register TVR = (3.6864E6 * T) -1 where T = the incoming bit period, and TVR = this register value. D0 TVR8 1 VALUE 000000000000 000000000001 ↓ 011111111111 ↓ 111111111111 FUNCTION 0 1 ↓ 2047R ↓ 4095 T = 271 ns T = 542 ns ↓ T = 555 µs (1800 bps) ↓ T = 1.11 ms For TV remote receive "oversampled" mode, this register value determines the input data sample rate. The sample rate is 3.6864 MHz divided by this register value. The sample rate should be set to as fast as possible, to give the best resolution on the incoming data edges, but should be less than 80% of the main UART communication baud rate. For TV remote receive "programmed T period" mode, this register sets the expected incoming bit cell time (T). The main UART communications rate must be set to at least 20% greater than 1/T. DS134F1 DS134PP2 19 19 CS8130 CS8130 Register 19, TV Remote Transmit Bit Rate Divider Register #1 D3 Register Reset (R) D2 D1 TBR3 TBR2 TBR1 1 1 1 D0 TBR0 1 Register 20, TV Remote Transmit Bit Rate Divider Register #2 D3 D2 Register TBR7 TBR6 Reset (R) 0 1 BIT TBR7-0 D1 D0 TBR5 1 TBR4 1 NAME TV remote mode transmit bit rate register TBR= (3.6864E6/(16*RATE)) -1 where TBR is this register value & RATE is the desired transmit bit rate. VALUE 01111111 127 R FUNCTION RATE = 1800 bps Register 21, Control Register #4 D3 Register Reset (R) BIT OSCE OSCL EXCK SRES 20 D2 D1 OSCE OSCL EXCK 0 0 0 NAME Disable crystal oscillator in D/C controlled power down state Set oscillator in low power mode Disable external clock output driver Software Reset D0 SRES 0 VALUE 0 1 0 1 0 1 0 1 FUNCTION R In D/C controlled power down state, crystal oscillator stays running. In D/C controlled power down state, crystal oscillator stops. R Oscillator in normal power, high accuracy, mode. Oscillator in low power, medium accuracy mode. R If crystal is used, enable clock output driver If crystal is used, disable clock output driver (Hi-Z) R Normal operation Causes a software reset, which forces all registers into their reset state. If ECHO is true, then the echo will occur at the current baud rate, before the baud rate changes to the default value. DS134F1 DS134PP2 CS8130 CS8130 Register 24, Receive ASK Timing Sensitivity Register D3 Register Reset (R) BIT RAT3-0 D2 D1 RAT3 RAT2 RAT1 0 0 0 D0 RAT0 0 NAME Receiver ASK Timing Sensitivity. Timing window = +0.27 µs to -RAT(2/3.6864E06) - 0.27 µs VALUE 0000 0001 0010 ↓ 1111 0 R +0.27 1 +0.27 2 +0.27 ↓ 15 +0.27 FUNCTION µs to -0.27 µs window (500 kHz ASK mode) µs to -0.54 - 0.27 µs window µs to -1.08 - 0.27 µs window ↓ µs to -8.14 - 0.27 µs window The timing window is relative to the modulation divider register nominal setting. Register 28, CS8130 Silicon Revision Register D3 Register BIT REV3-0 D2 D1 REV3 REV2 REV1 NAME CS8130 silicon revision level D0 REV0 VALUE 0000 FUNCTION 1st silicon, designed to meet DS134PP2 data sheet, dated June 1994 This register should be read by the CS8130 driver to allow CS8130 future enhancements to be recognized, and incorporated into future versions of the driver. DS134F1 DS134PP2 21 21 CS8130 CS8130 Grounding & Layout Optical Components Grounding and layout for the CS8130 are critical, because of the sensitive nature of the PIN diode amplifier. The CS8130 should be over its own dedicated ground plane. The PIN diode should be very close to the PINA and PINC pins. The PIN diode traces should be very short (< 5 mm), and should be surrounded by ground plane. There should be holes in the ground plane provided for mounting a metal shield over the CS8130 and the PIN diode for EMI shielding. The PIN diode and transmit LEDs should be positioned so as to line up the front optical surfaces of the packages. The optical surface of the PIN diode and transmit LED(s) should be positioned 1cm back from the daylight IR filter window inside the case of the equipment. This ensures that direct sunlight does not fall upon the top surface of the PIN diode. TEMIC (Tel: 408 970 5684) provides Telefunken infrared LEDs and PIN diodes which are compatible with the CS8130. Contact Crystal for details of additional qualified LED and PIN diode sources. Example Application Schematics Crystal has prepared some example schematics which demonstrate possible uses for the CS8130. Figure 8 shows a computer or PDA motherboard example, where one UART is used to drive both a wired RS232 COM port and an IR port. Figure 9 shows a pod schematic. This is an external unit which can be plugged into any existing COM port to create an IR port. An evaluation kit, CDB8130, is available from Crystal. This may be used as an example of the correct layout for the CS8130 and the optical components. Schematic & Layout Review Service Confirm Optimum Schematic & Layout Before Building Your Board. For Our Free Review Service Call Applications Engineering. C a l l : ( 5 1 2 ) 4 4 5 - 7 2 2 2 22 DS134F1 DS134PP2 CS8130 CS8130 10 Ω 10 µF + 0.1 µF 5 7 BPV23NF 8 12 VA+ VD+ AGND PINA +3V RESET CS8130 RXD FORM/BSY 5.2 Ω (2) 5.2 Ω (2) 1 4 17 3.6864 MHz PINC 47 µF Notes: (1) This circuit has not yet been built and debugged. (2) Choice of LED, power consumption and physical positioning will affect R value. EXTCLK XTALOUT 6 +3V 10 µF 19 XTALIN TSHA5502 + + 0.1 µF TXD LED1C D/C LED2C PWRDN CLKFR 18 11 13 16 14 15 10 9 TGND1 TGND2 DGND 2 3 20 +3V 0.33 µF 1 5 0.33 µF CIA- EN 2 CIA+ 4 0.33 µF VCC 3 SHDN CIB- C2+ MAX562 CIB+ C2- 14 25 24 0.33 µF UART 6 DSR 23 R1IN R1OUT 6 8 CTS 22 R2IN R2OUT 7 2 RXD 21 R3IN R3OUT 8 DB9 1 Serial Connector 9 (COM PORT) 4 DCD 20 R4IN R4OUT 9 RI 19 R5IN R5OUT 10 DTR 18 T1OUT T1IN 11 7 RTS 17 T2OUT T2IN 12 3 TXD 16 T3OUT T3IN 13 5 SG V- RS-232/IR SELECT 15 DSR CTS RXD DCD RI DTR RTS TXD 26 V+ 28 GND 27 0.68 µF UART to both RS232 and IR Port Interface Motherboard Example Schematic 0.33 µF Steven Harris Crystal Semiconductor 5/26/94 Figure 8. IR and RS232 from 1 UART DS134F1 DS134PP2 23 23 CS8130 CS8130 10 Ω 10 µF + 0.1 µF 5 7 BPV23NF 8 12 VA+ VD+ AGND EXTCLK PINC TSHA5502 PINA XTALIN 47 µF 5.5 Ω (2) 5.5 Ω (2) 1 4 LED1C +3V 0.33 µF 5 19 0.33 µF VCC CIB- CIA- XTALOUT 17 C2+ 18 C2- 13 11 T1IN 12 T2IN 6 R1OUT 7 R2OUT 8 R3OUT 16 FORM/BSY 14 TXD 15 D/C 11 RESET LED2C PWRDN CLKFR 10 +3V +3V 9 14 MAX562 EN Notes: (1) This circuit has not yet been built and debugged. (2) Choice of LED, power consumption and physical positioning will affect R value. (3) The creation of +3V or +5V supply is not included here. 24 26 V+ 28 GND 27 0.33 µF 25 T1OUT 18 T2OUT 17 23 R1IN 22 R2IN 21 R3IN V- 15 SHDN TGND1 TGND2 DGND 2 3 20 4 CIB+ 3 2 CIA+ 3.6864 MHz RXD +3V +3V 10 µF 1 CS8130 6 + + 0.1 µF 0.68 µF 0.33 µF RXD CTS TXD 2 8 3 DTR RTS 4 7 5 DB9 Serial Connector (COM PORT) 0.33 µF RS232 COM PORT to Infra Red Interface Pod Schematic Steven Harris Crystal Semiconductor 5/26/94 Figure 9. Example Pod Schematic 24 DS134F1 DS134PP2 CS8130 CS8130 LED1 CATHODE TRANSMIT GROUND 1 TRANSMIT GROUND 2 LED2 CATHODE ANALOG GROUND PIN DIODE ANODE PIN DIODE CATHODE ANALOG SUPPLY CLOCK FREQUENCY POWER DOWN LED1C TGND1 TGND2 LED2C AGND PINA PINC VA+ CLKFR PWRDN 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 DGND EXTCLK XTALOUT XTALIN FORM/BSY D/C TXD RXD VD+ RESET DIGITAL GROUND EXTERNAL CLOCK CRYSTAL OUTPUT CRYSTAL INPUT FORMAT/BUSY DATA/CONTROL TRANSMIT DATA RECEIVE DATA DIGITAL SUPPLY RESET Power Supplies VD+ - Digital Positive Supply. Digital positive supply voltage. Nominally +3V VA+ - Analog Positive Supply. Analog positive supply voltage. Nominally +3V. DGND - Digital Ground. Digital ground, 0V, connection. AGND - Analog Ground. Analog ground, 0V, connection. TGND1, TGND2 - Transmitter Grounds. LED Transmitter grounds, 0V, connections. Analog Pins LED1C, LED2C - Transmit LED Cathode. These pins are connected to the transmit LED cathode via resistors. Appropriate resistor choice allows user setting of LED current options. The anode of the LED is connected to the positive supply. PINC - Receiver PIN Diode Cathode Receiver PIN diode cathode. PINA - Receiver PIN Diode Anode. Receiver PIN diode anode. DS134F1 DS134PP2 25 25 CS8130 CS8130 Digital Pins RXD - Receiver Data Output Receiver output data. Normally connected to RxD on the UART. TXD - Transmit Data Input Transmitter input data. Normally connected to TxD on the UART. D/C - Data/Control Mode Input The D/C pin determines whether the input data on TXD is treated as data to be transmitted via the LED, or as control information to set up the CS8130 internal registers. The D/C pin also can act as a power down control. FORM/BSY - Received Data Format Output/Busy Signal Output If auto format detect mode is enabled, this pin indicates the format of the incoming data. FORM is low for ASK format data, and high for IRDA/HPSIR format data. In TV remote data mode (Mode 3), this pin becomes a handshake signal to the UART. FORM/BSY low means OK to send a character. FORM/BSY high means "I am busy, do not send another character". PWRDN - Power Down Control Input PWRDN low places the CS8130 into a very low power consumption "off" state. RESET - Reset Input RESET low places all the internal logic into a known state. All the control register bits are forced high or low, as defined in the register definition section. If the crystal oscillator is in use, then RESET must be held low for >25 ms, with PWRDN high and power applied. If an external clock is used, then the RESET pulse can be short (>1 µs). XTALIN, XTALOUT - Crystal Connections To use the internal oscillator, connect either a 3.6864 MHz or a 1.8432 MHz crystal between XTALOUT and XTALIN. If using an external clock, connect XTALIN to DGND. EXTCLK - External Clock Input or Output If no crystal is present on XTALIN and XTALOUT, EXTCLK becomes an input. A 3.6864 MHz or 1.8432 MHz clock should be connected to EXTCLK. XTALIN should be connected to DGND. If a crystal is present on XTALIN and XTALOUT, EXTCLK becomes an output. EXTCLK will output the same frequency as the crystal. The EXTCLK output driver may be disabled to conserve power. CLKFR - Clock Frequency Select Input Tie CLKFR to ground to select a 3.6864 MHz clock. Connect CLKFR to the VD+ pin to select a 1.8432 MHz clock. 26 DS134F1 DS134PP2 CS8130 20 PIN SSOP 28 PIN SSOP N E SSOP Package Dimensions 1 2 3 TOP VIEW D1 E 11 A2 e A A1 b2 L Seating Plane END VIEW SIDE VIEW INCHES MILLIMETERS Notes: 1. "D" and "E 1 " are reference datums and do not include mold flash or protrusions, but do include mold mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20mm per side. 2. Dimension b does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be 0.13mm total in excess of b dimension at maximum material condition. Dambar intrusion shall not reduce dimension b by more than 0.07mm at least material condition. 3. These dimensions apply to the flat section of the lead between 0.10 and 0.25mm from lead tips. 44 DS134F1 DIM MIN NOM MAX MIN NOM A - - 2.13 - - A1 0.05 0.15 0.25 0.002 A2 1.62 1.75 1.88 0.064 0.070 0.074 b 0.22 0.30 0.38 0.009 D E 7.80 0.084 0.006 0.010 0.012 0.015 2, 3 see other table see other table 7.40 MAX Note 1 8.20 0.291 0.307 0.323 E1 5.00 5.30 5.60 0.197 0.209 0.220 e 0.61 0.65 0.69 0.024 0.026 0.027 L 0.63 0.90 1.03 0.025 N ∝ 4° 0.035 0.040 see other table see other table 0° 1 8° 0° 4° 8° D MILLIMETERS N MIN NOM MAX 20 6.90 7.20 7.50 28 9.90 INCHES MIN NOM MAX 0.272 0.283 0.295 10.20 10.50 0.390 0.402 0.413 Note 1 1 27 CS8130 ORDERING INFORMATION Model Package CS8130-CS Temperature 20-pin SSOIC 0 to +70 °C ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION Model Number Peak Reflow Temp CS8130-CS 240 °C MSL Rating* 2 Max Floor Life 365 Days * MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020. REVISION HISTORY Revision Date Changes PP2 JUN 1994 Initial Release F1 SEP 2005 Updated device ordering info. Updated legal notice. Added MSL data.. Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries (“Cirrus”) believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. Smart AnalogTM is a Trademark of Crystal Semiconductor Corporation 28 DS134F1