EP9307 Data Sheet
FEATURES
•
•
•
•
•
Linux®, Microsoft® Windows® CE-enabled MMU
100-MHz System Bus
•
•
•
MaverickCrunch™ Math Engine
• Floating Point, Integer and Signal Processing
Instructions
• Optimized for digital music compression and
decompression algorithms.
• Hardware interlocks allow in-line coding.
Peripheral Bus
12 Channel DMA
(3) UARTs
w/
IrDA
(3) USB
Hosts
•
Clocks &
Timers
MaverickCrunchTM
Interrupts
& GPIO
ARM920T
MaverickKeyTM
Boot
ROM
D-Cache
16KB
I-Cache
16KB
Bus
Bridge
MMU
Keypad &
Touch
Screen I/F
USER INTERFACE
Serial
Audio
Interface
Touchscreen Interface with ADC
8 x 8 Keypad Scanner
One Serial Peripheral Interface (SPI) Port
• 6-channel or 2-channel Serial Audio Interface (I2S)
• 2-channel, Low-cost Serial Audio Interface (AC'97)
Internal Peripherals
• 12 Direct Memory Access (DMA) Channels
• Real-time Clock with Software Trim
• Dual PLL controls all clock domains.
• Watchdog Timer
• Two General-purpose 16-bit Timers
• One General-purpose 32-bit Timer
• One 40-bit Debug Timer
• Interrupt Controller
• Boot ROM
Package
• 272 pin TFBGA
•
MaverickKey™ IDs
• 32-bit unique ID can be used for DRM-compliant,
128-bit random ID.
Integrated Peripheral Interfaces
• 32-bit SDRAM Interface (up to 4 banks)
• 32/16-bit SRAM/FLASH/ROM
• Serial EEPROM Interface
• 1/10/100 Mbps Ethernet MAC
• Three UARTs
• Three-port USB 2.0 Full-speed Host (OHCI)
(12 Mbits per second)
• IrDA Interface
• LCD and Raster Interface with Graphics
Accelerator
COMMUNICATIONS PORTS
•
ARM9 SOC with Ethernet, USB,
Display, and Touchscreen
200-MHz ARM920T Processor
• 16-kbyte Instruction Cache
• 16-kbyte Data Cache
Processor Bus
Ethernet MAC
SRAM &
Flash I/F
Unified
SDRAM I/F
Video/LCD
Controller
Graphic
Accelerator
MEMORY AND STORAGE
Copyright 2010 Cirrus Logic (All Rights Reserved)
http://www.cirrus.com
Mar ‘10
DS667F2
1
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
OVERVIEW
The EP9307 is an ARM920T-based system-on-a-chip
(SOC) design with a large peripheral set targeted to a
variety of applications:
•
•
•
•
•
•
•
Thin client computers for business and home
Internet radio
Internet access devices
Industrial computers
Specialized terminals
Point of sale terminals
Test and measurement equipment
important role in the delivery of digital media such as
books or music, traditional software methods are quickly
becoming unreliable. The MaverickKey unique IDs
provide OEMs with a method of utilizing specific
hardware IDs such as those assigned for SDMI (Secure
Digital Music Initiative) or any other authentication
mechanism.
A high-performance 1/10/100 Mbps Ethernet media
access controller (MAC) is included along with external
interfaces to SPI, I2S audio, Raster/LCD, keypad and
touchscreen. A three-port USB 2.0 Full-speed Host
(OHCI) (12 Mbits per second) and three UARTs are
included as well.
The ARM920T microprocessor core with separate 16kbyte, 64-way set-associative instruction and data
caches is augmented by the MaverickCrunch™ coprocessor,
enabling
high-speed
floating
point
calculations.
The EP9307 is a high-performance, low-power, RISCbased, single-chip computer built around an ARM920T
microprocessor core with a maximum operating clock
rate of 200 MHz (184 MHz for industrial conditions). The
ARM core operates from a 1.8 V supply, while the I/O
operates at 3.3 V with power usage between 100 mW
and 750 mW (dependent on speed).
MaverickKey™ unique hardware programmed IDs are a
solution to the growing concern over secure web content
and commerce. With Internet security playing an
Table A. Change History
Revision
2
Date
Changes
PP1
July 2004
PP2
August 2004
Initial Release.
PP3
August 2004
Minor correction.
PP4
March 2005
Update electrical characteristics with most-current characterization data.
F1
February 2010
F2
March 2010
Correct error in pin out table, pages 42 & 43.
Removed “Preliminary Data” statement from legal disclaimer. Removed lead-containing device part numbers.
Increased minimum CVDD & VDD_PLL voltages from 1.65 V min. to 1.71 V min. Changed operating
temperatures to 0 to 60°C commercial, -40 to 70°C industrial.
Increased commercial/industrial temperatures to 70/85 deg. C max.
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table of Contents
FEATURES .........................................................................................................1
OVERVIEW .........................................................................................................2
Processor Core - ARM920T ......................................................................................... 6
MaverickCrunch™ Math Engine .................................................................................. 6
MaverickKey™ Unique ID ............................................................................................ 6
General Purpose Memory Interface (SDRAM, SRAM, ROM, FLASH) ........................ 6
Ethernet Media Access Controller (MAC) .................................................................... 7
Serial Interfaces (SPI, I2S and AC ’97) ........................................................................ 7
Raster/LCD Interface ................................................................................................... 7
Graphics Accelerator ................................................................................................... 8
Touch Screen Interface with 12-bit Analog-to-digital Converter (ADC) ........................ 8
64-key Keypad Interface .............................................................................................. 8
Universal Asynchronous Receiver/Transmitters (UARTs) ............................................ 9
Internal Boot ROM ....................................................................................................... 9
Triple-port USB Host .................................................................................................... 9
Two-wire Interface Support .......................................................................................... 9
Real-Time Clock with Software Trim .......................................................................... 10
PLL and Clocking ....................................................................................................... 10
Timers ........................................................................................................................ 10
Interrupt Controller ..................................................................................................... 10
Dual LED Drivers ....................................................................................................... 10
General Purpose Input/Output (GPIO) ....................................................................... 10
Reset and Power Management ..................................................................................11
Hardware Debug Interface ..........................................................................................11
12-Channel DMA Controller ........................................................................................11
Electrical Specifications .................................................................................12
Absolute Maximum Ratings ....................................................................................... 12
Recommended Operating Conditions ........................................................................ 12
DC Characteristics ..................................................................................................... 13
Timings .............................................................................................................14
Memory Interface ....................................................................................................... 15
Ethernet MAC Interface ............................................................................................ 30
Audio Interface ........................................................................................................... 32
AC’97 ........................................................................................................................ 36
LCD Interface ............................................................................................................ 37
ADC ........................................................................................................................... 38
JTAG .......................................................................................................................... 39
272 Pin TFBGA Package Outline ...................................................................40
272 TFBGA Diagram ................................................................................................. 40
272 Pin TFBGA Pinout (Bottom View) ....................................................................... 41
Acronyms and Abbreviations ........................................................................48
Units of Measurement .....................................................................................48
ORDERING INFORMATION ............................................................................49
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
3
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
List of Figures
Figure 1. Timing Diagram Drawing Key ................................................................................. 14
Figure 2. SDRAM Load Mode Register Cycle Timing Measurement ..................................... 15
Figure 3. SDRAM Burst Read Cycle Timing Measurement ................................................... 16
Figure 4. SDRAM Burst Write Cycle Timing Measurement ................................................... 17
Figure 5. SDRAM Auto Refresh Cycle Timing Measurement ................................................ 18
Figure 6. Static Memory Single Word Read Cycle Timing Measurement .............................. 19
Figure 7. Static Memory Single Word Write Cycle Timing Measurement .............................. 20
Figure 8. Static Memory Multiple Word Read 8-bit Cycle Timing Measurement .................... 21
Figure 9. Static Memory Multiple Word Write 8-bit Cycle Timing Measurement .................... 22
Figure 10. Static Memory Multiple Word Read 16-bit Cycle Timing Measurement ................ 23
Figure 11. Static Memory Multiple Word Write 16-bit Cycle Timing Measurement ................ 24
Figure 12. Static Memory Burst Read Cycle Timing Measurement ....................................... 25
Figure 13. Static Memory Burst Write Cycle Timing Measurement ....................................... 26
Figure 14. Static Memory Single Read Wait Cycle Timing Measurement ............................. 27
Figure 15. Static Memory Single Write Wait Cycle Timing Measurement .............................. 28
Figure 16. Static Memory Turnaround Cycle Timing Measurement ....................................... 29
Figure 17. Ethernet MAC Timing Measurement ..................................................................... 31
Figure 18. TI Single Transfer Timing Measurement ............................................................... 33
Figure 19. Microwire Frame Format, Single Transfer ............................................................ 33
Figure 20. SPI Format with SPH=1 Timing Measurement ..................................................... 34
Figure 21. Inter-IC Sound (I2S) Timing Measurement ........................................................... 35
Figure 22. AC ‘97 Configuration Timing Measurement .......................................................... 36
Figure 23. LCD Timing Measurement .................................................................................... 37
Figure 24. ADC Transfer Function ......................................................................................... 38
Figure 25. JTAG Timing Measurement .................................................................................. 39
Figure 26. 272 Pin TFBGA Diagram ...................................................................................... 40
Figure 27. 272 Pin TFBGA Pinout
.................................................................................... 42
4
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
List of Tables
Table A. Change History .......................................................................................................... 2
Table B. General Purpose Memory Interface Pin Assignments .............................................. 6
Table C. Ethernet Media Access Controller Pin Assignments ................................................. 7
Table D. Audio Interfaces Pin Assignment .............................................................................. 7
Table E. LCD Interface Pin Assignments ................................................................................ 8
Table F. Touch Screen Interface with 12-bit Analog-to-Digital Converter Pin Assignments ... 8
Table G. 64-Key Keypad Interface Pin Assignments ............................................................... 8
Table H. Universal Asynchronous Receiver / Transmitters Pin Assignments .......................... 9
Table I. Triple Port USB Host Pin Assignments ..................................................................... 9
Table J. Two-Wire Port with EEPROM Support Pin Assignments .......................................... 9
Table K. Real-Time Clock with Pin Assignments ................................................................... 10
Table L. PLL and Clocking Pin Assignments ........................................................................ 10
Table M.External Interrupt Controller Pin Assignment .......................................................... 10
Table N. Dual LED Pin Assignments ..................................................................................... 10
Table O. General Purpose Input/Output Pin Assignment ...................................................... 11
Table P. Reset and Power Management Pin Assignments ................................................... 11
Table Q. Hardware Debug Interface ...................................................................................... 11
Table R. 272 Pin Diagram Dimensions .................................................................................. 41
Table S. Pin Descriptions ..................................................................................................... 46
Table T. Pin Multiplex Usage Information ............................................................................. 47
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
5
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Processor Core - ARM920T
The ARM920T is a Harvard architecture processor with
separate 16 kbyte instruction and data caches with an 8word line length but a unified memory. The processor
utilizes a five-stage pipeline consisting of fetch, decode,
execute, memory and write stages. Key features include:
•
•
•
•
•
•
•
•
ARM (32-bit) and Thumb (16-bit compressed)
instruction sets
32-bit Advanced Micro-Controller Bus Architecture
(AMBA)
16 kbyte Instruction Cache with lockdown
16 kbyte Data Cache (programmable write-through or
write-back) with lockdown
MMU for Linux®, Microsoft® Windows® CE and other
operating systems
Translation Look Aside Buffers with 64 Data and 64
Instruction Entries
Programmable Page Sizes of 1 Mbyte, 64 kbyte,
4 kbyte, and 1 kbyte
Independent lockdown of TLB Entries
MaverickCrunch™ Math Engine
The MaverickCrunch Engine is a mixed-mode
coprocessor designed primarily to accelerate the math
processing required to rapidly encode digital audio
formats. It accelerates single- and double-precision
integer and floating point operations plus an integer
multiply-accumulate
(MAC)
instruction
that
is
considerably faster than the ARM920T's native MAC
instruction. The ARM920T coprocessor interface is
utilized thereby sharing its memory interface and
instruction stream. Hardware forwarding and interlock
allows the ARM to handle looping and addressing while
MaverickCrunch handles computation. Features include:
•
•
•
•
•
•
•
•
IEEE-754 single and double precision floating point
32/64-bit integer
Add/multiply/compare
Integer MAC 32-bit input with 72-bit accumulate
Integer Shifts
Floating point to/from integer conversion
Sixteen 64-bit register files
Four 72-bit accumulators
MaverickKey™ Unique ID
MaverickKey unique hardware programmed IDs are a
solution to the growing concern over secure web content
and commerce. With Internet security playing an
important role in the delivery of digital media such as
books or music, traditional software methods are quickly
becoming unreliable. The MaverickKey unique IDs
6
provide OEMs with a method of utilizing specific
hardware IDs such as those assigned for SDMI (Secure
Digital Music Initiative) or any other authentication
mechanism.
Both a specific 32-bit ID as well as a 128-bit random ID
are programmed into the EP9307 through the use of
laser probing technology. These IDs can then be used to
match secure copyrighted content with the ID of the
target device the EP9307 is powering, and then deliver
the copyrighted information over a secure connection. In
addition, secure transactions can benefit by also
matching device IDs to server IDs. MaverickKey IDs
provide a level of hardware security required for today’s
Internet appliances.
General Purpose Memory Interface (SDRAM,
SRAM, ROM, FLASH)
The EP9307 features a unified memory address model
where all memory devices are accessed over a common
address/data bus. A separate internal port is dedicated to
the read-only Raster/LCD refresh engine, while the rest
of the memory accesses are performed via the Processor
bus. The SRAM memory controller supports 8, 16 and
32-bit devices and accommodates an internal boot ROM
concurrently with 32-bit SDRAM memory.
•
•
•
•
1 to 4 banks of 32-bit, 100 MHz SDRAM
One internal port dedicated to the Raster/LCD
Refresh Engine (Read Only)
Address and data bus shared between SDRAM,
SRAM, ROM, and FLASH memory
NOR FLASH memory supported
Table B. General Purpose Memory Interface Pin Assignments
Pin Mnemonic
Pin Description
SDCLK
SDRAM Clock
SDCLKEN
SDRAM Clock Enable
SDCSn[3:0]
SDRAM Chip Selects 3-0
RASn
SDRAM RAS
CASn
SDRAM CAS
SDWEn
SDRAM Write Enable
CSn[7:6] and CSn[3:0]
Chip Selects 7, 6, 3, 2, 1, 0
AD[25:0]
Address Bus 25-0
DA[31:0]
Data Bus 31-0
DQMn[3:0]
SDRAM Output Enables / Data Masks
WRn
SRAM Write Strobe
RDn
SRAM Read/OE Strobe
WAITn
SRAM Wait Input
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Ethernet Media Access Controller (MAC)
Table D. Audio Interfaces Pin Assignment
The MAC subsystem is compliant with the ISO/TEC
802.3 topology for a single shared medium with several
stations. Multiple MII-compliant PHYs are supported.
Features include:
•
•
Supports 1/10/100 Mbps transfer rates for
home/small-business/large-business applications
Interfaces to an off-chip PHY through industry
standard Media Independent Interface (MII)
Pin
Name
Normal Mode
I2S on SSP
Mode
I2S on AC'97
Mode
Pin
Description
Pin Description
Pin Description
SCLK1
SPI Bit Clock
SFRM1
SPI Frame Clock I2S Frame Clock
SSPRX1 SPI Serial Input
SSPTX1
SPI Serial
Output
Pin Description
SPI Bit Clock
SPI Frame Clock
I2S Serial Input
SPI Serial Input
I2S Serial Output
SPI Serial Output
(No I2S Master
Clock)
Table C. Ethernet Media Access Controller Pin Assignments
Pin Mnemonic
I2S Serial Clock
ARSTn
AC'97 Reset
AC'97 Reset
I2S Master Clock
AC'97 Bit Clock
I2S Serial Clock
MDC
Management Data Clock
ABITCLK AC'97 Bit Clock
MDIO
Management Data I/O
ASYNC
Receive Clock
AC'97 Frame
Clock
I2S Frame Clock
RXCLK
AC'97 Frame
Clock
MIIRXD[3:0]
Receive Data
ASDI
AC'97 Serial
Input
AC'97 Serial Input
I2S Serial Input
RXDVAL
Receive Data Valid
RXERR
Receive Data Error
ASDO
AC'97 Serial
Output
AC'97 Serial
Output
I2S Serial Output
TXCLK
Transmit Clock
MIITXD[3:0]
Transmit Data
TXEN
Transmit Enable
TXERR
Transmit Error
CRS
Carrier Sense
CLD
Collision Detect
Raster/LCD Interface
Serial Interfaces (SPI, I2S and AC ’97)
The SPI port can be configured as a master or a slave,
supporting the National Semiconductor®, Motorola®, and
Texas Instruments® signaling protocols.
The Raster/LCD interface provides data and interface
signals for a variety of display types. It features fully
programmable video interface timing for non-interlaced
flat panel or dual scan displays. Resolutions up to
1024 x 768 are supported from a unified SDRAM based
frame buffer. A 16-bit PWM provides control for LCD
panel contrast. LCD specific features include:
•
•
The AC'97 port supports multiple codecs for multichannel
audio output with a single stereo input. The I2S port can
be configured to support two channel, 24 bit audio.
•
These ports are multiplexed so that I2S port 0 will take
over either the AC'97 pins or the SPI pins. The second
and third I2S ports' serial input and serial output pins are
multiplexed with EGPIO[4,5,6,13]. The clocks supplied in
the first I2S port are also used for the second and third
I2S ports.
•
•
•
•
•
Normal Mode: One SPI Port and one AC’97 Port
•
I2S on SSP Mode: One AC’97 Port and up to three I2S
Ports
•
I2S on AC’97 Mode: One SPI Port and up to three I2S
Ports
Note:
DS667F2
•
Timing and interface signals for digital LCD and TFT
displays
Full programmability for either non-interlaced or dualscan color and grayscale flat panel displays
Dedicated data path to SDRAM controller for
improved system performance
Pixel depths of 4, 8, 16, or 24 bits per pixel or 256
levels of grayscale
Hardware Cursor up to 64 x 64 pixels
256 x 18 Color Lookup Table
Hardware Blinking
8-bit interface to low-end panel
I2S may not be output on AC’97 and SSP ports at the
same time.
Copyright 2010 Cirrus Logic (All Rights Reserved)
7
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table E. LCD Interface Pin Assignments
Pin Mnemonic
Table F. Touch Screen Interface with 12-bit Analog-to-Digital
Converter Pin Assignments
Pin Description
Pin Mnemonic
SPCLK
Pixel Clock
P[17:0]
Pixel Data Bus [17:0]
HSYNC/LP
Horizontal
Synchronization/Line Pulse
VCSYNC/FP
Vertical or Composite
Synchronization / Frame Pulse
BLANK
Composite Blank
BRIGHT
Pulse Width Modulated Brightness
Xp, Xm
Pin Description
Touch screen ADC X Axis
Yp, Ym
Touch screen ADC Y Axis
SXp, SXm
Touch screen ADC X Axis
Voltage Feedback
SYp, SYm
Touch screen ADC Y Axis
Voltage Feedback
64-key Keypad Interface
Graphics Accelerator
The EP9307 contains a hardware graphics acceleration
engine that improves graphic performance by handling
block copy, block fill and hardware line draw operations.
The Graphics Accelerator is used in the system to offload graphics operations from the processor.
Pixel depths supported by the Graphics Accelerator are
4, 8, 16 or 24 bits per pixel (bpp). The 24 bits per pixel
mode can be operated as packed (4 pixels every 3
words) or unpacked (1 pixel per word with the high byte
unused.)
The block copy operations of the Graphics Accelerator
are similar to a DMA (Direct Memory Access) transfer
that understands pixel organization, block width,
transparency, and transformation from 1bpp to higher 4,
8, 16 or 24 bpp.
The line draw operations also allow for solid lines or
dashed lines. The colors for line drawing can be either
foreground color and background color or foreground
color with the background being transparent.
Touch Screen Interface with 12-bit Analogto-digital Converter (ADC)
The keypad circuitry scans an 8 x 8 array of 64 normally
open, single pole switches. Any one or two keys
depressed will be de-bounced and decoded. An interrupt
is generated whenever a stable set of depressed keys is
detected. If the keypad is not utilized, the 16 column/row
pins may be used as general purpose I/O. The Keypad
interface:
•
•
•
•
•
Provides scanning, debounce, and decoding for a 64key switch array.
Scans an 8-row by 8-column matrix.
May decode 2 keys at once.
Generates an interrupt when a new stable key is
determined.
Also generates a 3-key reset interrupt.
Table G. 64-Key Keypad Interface Pin Assignments
Pin Mnemonic
Pin
Description
Alternative Usage
COL[7:0]
Key Matrix Column
Inputs
General Purpose I/O
ROW[7:0]
Key Matrix Row
Inputs
General Purpose I/O
The touch screen interface performs all sampling,
averaging, ADC range checking, and control for a wide
variety of analog resistive touch screens. This controller
only interrupts the processor when a meaningful change
occurs. The touch screen hardware may be disabled and
the switch matrix and ADC controlled directly if desired.
Features include:
•
•
•
8
Support for 4-, 5-, 7-, or 8-wire analog resistive touch
screens.
Flexibility - unused lines may be used for temperature
sensing or other functions.
Touch screen interrupt function.
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Universal Asynchronous
Receiver/Transmitters (UARTs)
Three 16550-compatible UARTs are supplied. Two
provide asynchronous HDLC (High-level Data Link
Control) protocol support for full duplex transmit and
receive. The HDLC receiver handles framing, address
matching, CRC checking, control-octet transparency, and
optionally passes the CRC to the host at the end of the
packet. The HDLC transmitter handles framing, CRC
generation, and control-octet transparency. The host
must assemble the frame in memory before
transmission. The HDLC receiver and transmitter use the
UART FIFOs to buffer the data streams. A third IrDA®
compatible UART is also supplied.
•
•
•
UART1 supports modem bit rates up to 115.2 kbps,
supports HDLC and includes a 16 byte FIFO for
receive and a 16 byte FIFO for transmit. Interrupts are
generated on Rx, Tx and modem status change.
UART2 contains an IrDA encoder operating at either
the slow (up to 115 kbps), medium (0.576 or 1.152
Mbps), or fast (4 Mbps) IR data rates. It also has a 16
byte FIFO for receive and a 16 byte FIFO for transmit.
UART3 supports HDLC and includes a 16 byte FIFO
for receive and a 16 byte FIFO for transmit. Interrupts
are generated on Rx and Tx.
Triple-port USB Host
The USB Open Host Controller Interface (Open HCI)
provides full-speed serial communications ports at a
baud rate of 12 Mbits/sec. Up to 127 USB devices
(printer, mouse, camera, keyboard, etc.) and USB hubs
can be connected to the USB host in the USB “tieredstar” topology.
This includes the following features:
•
•
•
Compliance with the USB 2.0 specification
Compliance with the Open HCI Rev 1.0 specification
Supports both low-speed (1.5 Mbps) and full-speed
(12 Mbps) USB device connections
• Root HUB integrated with 3 downstream USB ports
• Transceiver buffers integrated, over-current protection
on ports
• Supports power management
• Operates as a master on the bus
The Open HCI host controller initializes the master DMA
transfer with the AHB bus:
•
•
•
•
Fetches endpoint descriptors and transfer descriptors
Accesses endpoint data from system memory
Accesses the HC communication area
Writes status and retire transfer descriptor
Table H. Universal Asynchronous Receiver / Transmitters Pin
Assignments
Pin Mnemonic
Pin Name - Description
Table I. Triple Port USB Host Pin Assignments
Pin Mnemonic
Pin Name - Description
USBp[2:0]
USB Positive signals
USBm[2:0]
USB Negative Signals
TXD0
UART1 Transmit
RXD0
UART1 Receive
CTSn
UART1 Clear To
Send / Transmit Enable
DSRn/DCDn
UART1 Data Set
Ready / Data Carrier Detect
DTRn
UART1 Data Terminal Ready
RTSn
UART1 Ready To Send
EGPIO[0]/RI
UART1 Ring Indicator
TXD1/SIROUT
UART2 Transmit / IrDA
Output
Pin Mnemonic
RXD1/SIRIN
UART2 Receive / IrDA Input
EECLK
Two-wire Interface Clock
TXD2
UART3 Transmit
General
Purpose I/O
RXD2
UART3 Receive
EEDATA
Two-wire Interface Data
General
Purpose I/O
TENn
HDLC3 Transmit Enable
Two-wire Interface Support
The two-wire interface provides communication and
control for synchronous-serial-driven devices.
Table J. Two-Wire Port with EEPROM Support Pin Assignments
Pin Name - Description
Alternative
Usage
Internal Boot ROM
The Internal 16-kbyte ROM allows booting from FLASH
memory, SPI or UART. Consult the EP9307 User’s Guide
for operational details.
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
9
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Real-Time Clock with Software Trim
The software trim feature on the real time clock (RTC)
provides software controlled digital compensation of the
32.768 KHz input clock. This compensation is accurate to
±1.24 sec/month.
Note:
A real time clock must be connected to RTCXTALI or
the EP9307 device will not boot.
low level sensitive inputs. GPIO pins programmed as
interrupts may be programmed as active high level
sensitive, active low level sensitive, rising edge triggered,
falling edge triggered, or combined rising/falling edge
triggered.
•
•
Table K. Real-Time Clock with Pin Assignments
Pin Mnemonic
Pin Name - Description
RTCXTALI
Real-Time Clock Oscillator Input
RTCXTALO
Real-Time Clock Oscillator Output
•
•
•
PLL and Clocking
The Processor and the Peripheral Clocks operate from a
single 14.7456 MHz crystal.
Supports 64 interrupts from a variety of sources (such
as UARTs, GPIO, and key matrix)
Routes interrupt sources to either the ARM920T’s
IRQ or FIQ (Fast IRQ) inputs
Three dedicated off-chip interrupt lines operate as
active high level sensitive interrupts
Any of the 16 GPIO lines maybe configured to
generate interrupts
Software supported priority mask for all FIQs and
IRQs
Table M. External Interrupt Controller Pin Assignment
Pin Mnemonic
The Real Time Clock operates from a 32.768 KHz
external oscillator.
Table L. PLL and Clocking Pin Assignments
Pin Mnemonic
Pin Name - Description
XTALI
Main Oscillator Input
XTALO
Main Oscillator Output
VDD_PLL
Main Oscillator Power
GND_PLL
Main Oscillator Ground
Timers
The Watchdog Timer ensures proper operation by
requiring periodic attention to prevent a reset-on-timeout.
Two 16-bit timers operate as free running down-counters
or as periodic timers for fixed interval interrupts and have
a range of 0.03 ms to 4.27 seconds.
One 32-bit timer, plus a 6-bit prescale counter, has a
range of 0.03 μs to 73.3 hours.
One 40-bit debug timer, plus a 6-bit prescale counter, has
a range of 1.0 μs to 12.7 days.
Interrupt Controller
The interrupt controller allows up to 62 interrupts to
generate an Interrupt Request (IRQ) or Fast Interrupt
Request (FIQ) signal to the processor core. Thirty-two
hardware priority assignments are provided for assisting
IRQ vectoring, and two levels are provided for FIQ
vectoring. This allows time critical interrupts to be
processed in the shortest time possible. Internal
interrupts may be programmed as active high or active
10
INT[2:0]
Pin Name - Description
External Interrupts 2, 1, 0
Dual LED Drivers
Two pins are assigned specifically to drive external
LEDs.
Table N. Dual LED Pin Assignments
Pin Mnemonic
Pin Name Description
GRLED
Green LED
General Purpose I/O
REDLED
Red LED
General Purpose I/O
Alternative Usage
General Purpose Input/Output (GPIO)
The 14 EGPIO pins may each be configured individually
as an output, an input, or an interrupt input.
There are 22 pins that may alternatively be used as input,
output, or open-drain pins, but do not support interrupts.
These pins are:
• Key Matrix ROW[7:0], COL[7:0]
• Ethernet MDIO
• Both LED Outputs
• Two-wire Clock and Data
• GGPIO[2]
• HGPIO[7:2]
6 pins may alternatively be used as inputs only:
• CTSn, DSRn/DCDn
• 4 Interrupt Lines
2 pins may alternatively be used as outputs only:
• RTSn
• ARSTn
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table O. General Purpose Input/Output Pin Assignment
Pin Mnemonic
decrement, or stay at the same value. All DMA
addresses are physical, not virtual addresses.
Pin Name - Description
EGPIO[15]
EGPIO[13:0]
Expanded General Purpose Input / Output
Pins with Interrupts
FGPIO[7]
FGPIO[5]
FGPIO[0]
Expanded General Purpose Input / Output
Pins with Interrupts
Reset and Power Management
The chip may be reset through the PRSTn pin or through
the open drain common reset pin, RSTOn.
Clocks are managed on a peripheral-by-peripheral basis
and may be turned off to conserve power.
The processor clock is dynamically adjustable from 0 to
200 MHz (184 MHz for industrial conditions).
Table P. Reset and Power Management Pin Assignments
Pin Mnemonic
Pin Name - Description
PRSTn
Power On Reset
RSTOn
User Reset In/Out – Open Drain –
Preserves Real Time Clock value
Hardware Debug Interface
The JTAG interface allows use of ARM’s Multi-ICE or
other in-circuit emulators.
Table Q. Hardware Debug Interface
Pin Mnemonic
Pin Name - Description
TCK
JTAG Clock
TDI
JTAG Data In
TDO
JTAG Data Out
TMS
JTAG Test Mode Select
TRSTn
JTAG Port Reset
12-Channel DMA Controller
The DMA module contains 12 separate DMA channels.
These may be used for peripheral-to-memory or
memory-to-peripheral access. Two of these are
dedicated to memory-to-memory transfers. Each DMA
channel is connected to the 16-bit DMA request bus.
The request bus is a collection of requests, Serial Audio
and UARTs. Each DMA channel can be used
independently or dedicated to any request signal. For
each DMA channel, source and destination addressing
can be independently programmed to increment,
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
11
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Electrical Specifications
Absolute Maximum Ratings
(All grounds = 0 V, all voltages with respect to 0 V)
Parameter
Power Supplies
Total Power Dissipation
Symbol
Min
Max
Unit
RVDD
CVDD
VDD_PLL
VDD_ADC
-
3.96
2.16
2.16
3.96
V
V
V
V
-
2
W
(Note 1)
Input Current per Pin, DC (Except supply pins)
-
±10
mA
Output current per pin, DC
-
±50
mA
-0.3
RVDD+0.3
V
-40
+125
°C
Digital Input voltage
(Note 2)
Storage temperature
Note:
1. Includes all power generated due to AC and/or DC output loading.
2. The power supply pins are at maximum values listed in “Recommended Operating Conditions”, below.
WARNING: Operation beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
Recommended Operating Conditions
(All grounds = 0 V, all voltages with respect to 0 V)
Parameter
Symbol
Min
Typ
Max
Unit
RVDD
CVDD
VDD_PLL
VDD_ADC
3.0
1.71
1.71
3.0
3.3
1.80
1.80
3.3
3.6
1.94
1.94
3.6
V
V
V
V
Operating Ambient Temperature - Commercial
TA
0
+25
+70
°C
Operating Ambient Temperature - Industrial
TA
-40
+25
+85
°C
FCLK
-
-
200
MHz
Processor Clock Speed - Industrial
FCLK
-
-
184
MHz
System Clock Speed - Commercial
HCLK
-
-
100
MHz
System Clock Speed - Industrial
HCLK
-
-
92
MHz
Power Supplies
Processor Clock Speed - Commercial
12
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
DC Characteristics
(TA = 0 to 70° C; CVDD = VDD_PLL = 1.8; RVDD = 3.3 V;
All grounds = 0 V; all voltages with respect to 0 V unless otherwise noted)
Parameter
High level output voltage
Iout = -4 mA
Low level output voltage
Iout = 4 mA
Symbol
Min
Max
Unit
Voh
0.85 × RVDD
-
V
Vol
-
0.15 × RVDD
V
(Note 3)
High level input voltage
(Note 4)
Vih
0.65 × RVDD
VDD + 0.3
V
Low level input voltage
(Note 4)
Vil
−0.3
0.35 × RVDD
V
High level leakage current
Vin = 3.3 V
(Note 4)
Iih
-
10
µA
Low level leakage current
Vin = 0
(Note 4)
Iil
-
-10
µA
Parameter
Min
Typ
Max
Unit
Power Supply Pins (Outputs Unloaded)
Power Supply Current:
CVDD/VDD_PLL Total
RVDD
-
190
45
240
80
mA
mA
Low-Power Mode Supply Current
CVDD/VDD_PLL Total
RVDD
-
2
1.0
3.5
2
mA
mA
Note:
DS667F2
3. For open drain pins, high level output voltage is dependent on the external load.
4. All inputs that do not include internal pull-ups or pull-downs, must be externally driven for proper operation (See Table S on
page 46). If an input is not driven, it should be tied to power or ground, depending on the particular function. If an I/O pin is not
driven and programmed as an input, it should be tied to power or ground through its own resistor.
Copyright 2010 Cirrus Logic (All Rights Reserved)
13
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Timings
Timing Diagram Conventions
This data sheet contains one or more timing diagrams. The following key explains the components used in these
diagrams. Any variations are clearly labelled when they occur. Therefore, no additional meaning should be attached
unless specifically stated.
Clock
High to Low
High/Low to High
Bus Change
Bus Valid
Undefined/Invalid
Valid Bus to Tristate
Bus/Signal Omission
Figure 1. Timing Diagram Drawing Key
Timing Conditions
Unless specified otherwise, the following conditions are true for all timing measurements.
• TA = 0 to 70° C
• CVDD = VDD_PLL = 1.8V
• RVDD = 3.3 V
• All grounds = 0 V
• Logic 0 = 0 V, Logic 1 = 3.3 V
• Output loading = 50 pF
• Timing reference levels = 1.5 V
• The Processor Bus Clock (HCLK) is programmable and is set by the user. The frequency is typically between
33 MHz and 100 MHz (92 MHz for industrial conditions).
14
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Memory Interface
Figure 2 through Figure 5 define the timings associated with all phases of the SDRAM. The following table contains the
values for the timings of each of the SDRAM modes.
Parameter
Symbol
Min
Typ
Max
Unit
SDCLK high time
tclk_high
-
(tHCLK) / 2
-
ns
SDCLK low time
tclk_low
-
(tHCLK) / 2
-
ns
tclkrf
-
2
4
ns
SDCLK rise/fall time
Signal delay from SDCLK rising edge time
td
-
-
8
ns
Signal hold from SDCLK rising edge time
th
1
-
-
ns
DQMn delay from SDCLK rising edge time
tDQd
-
-
8
ns
DQMn hold from SDCLK rising edge time
tDQh
1
-
-
ns
DA valid setup to SDCLK rising edge time
tDAs
2
-
-
ns
DA valid hold from SDCLK rising edge time
tDAh
3
-
-
ns
SDRAM Load Mode Register Cycle
tclk_low
tclkrf
tclk_high
SDCLK
td
th
SDCSn
RASn
CASn
SDWEn
DQMn
AD
OP-Code
DA
Figure 2. SDRAM Load Mode Register Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
15
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
SDRAM Burst Read Cycle
tclk_low
tclk_high
SDCLK
tclkrf
td
th
SDCSn
RASn
CASn
SDWEn
tDQh
tDQd
DQMn
CL = 2
tDQh
DQMn
CL = 3
AD
td
tDAs
DA
tDAh
n
n+1
n+2
n+3
CL = 2
tDAs
DA
CL = 3
tDAh
n
n+1
n+2
n+3
Figure 3. SDRAM Burst Read Cycle Timing Measurement
16
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
SDRAM Burst Write Cycle
tclk_high
tclk_low
SDCLK
tclkrf
td
th
th
SDCSn
RASn
CASn
SDWEn
DQMn
AD
DA
n
n +1
n+2
n+3
Figure 4. SDRAM Burst Write Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
17
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
SDRAM Auto Refresh Cycle
tclk_high
tclk_low
SDCLK
tclkrf
td
SDCSn
th
7
b
d
e
RASn
CASn
SDWEn
Note:
Chip select shown as bus to illustrate multiple devices being put into auto refresh in one access
Figure 5. SDRAM Auto Refresh Cycle Timing Measurement
18
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Single Word Read Cycle
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to CSn assert time
tADs
0
-
-
ns
AD hold from CSn deassert time
tADh
tHCLK
-
-
ns
RDn assert time
tRDpw
-
tHCLK × (WST1 + 2)
-
ns
CSn to RDn delay time
tRDd
-
-
3
ns
tDQMd
-
-
1
ns
DA setup to RDn deassert time
tDAs
tHCLK + 12
-
-
ns
DA hold from RDn deassert time
tDAh
0
-
-
ns
CSn assert to DQMn assert delay time
See “Timing Conditions” on page 14 for definition of HCLK.
tADs
tADh
AD
CSn
WRn
tRDd
tRDd
RDn
DQMn
tDQMd
tDAs
tDAh
DA
WAIT
Figure 6. Static Memory Single Word Read Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
19
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Single Word Write Cycle
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to WRn assert time
tADs
tHCLK
-3
-
-
ns
AD hold from WRn deassert time
tADh
tHCLK × 2
-
-
ns
WRn deassert to CSn deassert time
tCSh
7
-
-
ns
CSn to WRn assert delay time
tWRd
-
-
2
ns
WRn assert time
tWRpw
-
tHCLK × (WST1 + 1)
-
ns
CSn to DQMn assert delay time
tDQMd
-
-
1
ns
WRn deassert to DA transition time
tDAh
tHCLK
-
-
ns
WRn assert to DA valid
tDAV
-
-
8
ns
tADs
tADh
AD
tCSh
CSn
tWRd
tWRpw
WRn
RDn
DQMn
tDQMd
tDAV
tDAh
DA
WAIT
Figure 7. Static Memory Single Word Write Cycle Timing Measurement
20
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory 32-bit Read on 8-bit External Bus
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to CSn assert time
tADs
tHCLK
-
-
ns
CSn assert to Address transition time
tAD1
-
tHCLK × (WST1 + 1)
-
ns
Address assert time
tAD2
-
tHCLK × (WST1 + 1)
-
ns
AD transition to CSn deassert time
tAD3
-
tHCLK × (WST1 + 2)
-
ns
tADh
-
ns
tHCLK
-
tRDpwL
-
tHCLK × (4 × WST1 + 5)
-
ns
tRDd
-
-
3
ns
CSn assert to DQMn assert delay time
tDQMd
-
-
1
ns
DA setup to AD transition time
tDAs1
15
-
-
ns
DA setup to RDn deassert time
tDAs2
tHCLK + 12
-
-
ns
DA hold from AD transition time
tDAh1
0
-
-
ns
DA hold from RDn deassert time
tDAh2
0
-
-
ns
AD hold from CSn deassert time
RDn assert time
CSn to RDn delay time
tADs
tAD1
tAD2
tAD2
tADh
tAD3
AD
CSn
WRn
tRDd
tRDd
RDn
tDQMd
DQMn
tDAh1
tDAh1
tDAh11
tDAh2
DA
tDAs1
tDAs1
tDAs1
tDAs2
WAIT
Figure 8. Static Memory Multiple Word Read 8-bit Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
21
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory 32-bit Write on 8-bit External Bus
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to WRn assert time
tADs
tHCLK − 3
-
-
ns
WRn/DQMn deassert to AD transition time
tADd
-
-
tHCLK + 6
ns
AD hold from WRn deassert time
tADh
tHCLK × 2
-
-
ns
CSn hold from WRn deassert time
tCSh
7
-
-
ns
tWRd
2
ns
CSn to WRn assert delay time
-
-
WRn assert time
tWRpwL
-
tHCLK × (WST1 + 1)
-
ns
WRn deassert time
tWRpwH
-
tHCLK × 2
(tHCLK × 2) + 14
ns
tDQMd
-
-
1
ns
DQMn assert time
tDQMpwL
-
tHCLK × (WST1 + 1)
-
ns
DQMn deassert time
tDQMpwH
-
-
(tHCLK × 2) + 7
ns
WRn / DQMn deassert to DA transition time
tDAh
tHCLK
-
-
ns
WRn / DQMn assert to DA valid time
tDAV
-
-
8
ns
CSn to DQMn assert delay time
tADs
tADd
tADd
tADd
tADh
AD
CSn
tWRd
tWRpwL
tWRpwL
tCSh
tWRpwL
WRn
tWRpwH
tWRpwH
tWRpwH
RDn
tDQMd
tDQMpwL
tDQMpwL
tDQMpwL
DQMn
tDQMpwH
tDAV
tDQMpwH
tDAV
tDQMpwH
tDAV
tDAV
DA
tDAh
tDAh
tDAh
tDAh
WAIT
Figure 9. Static Memory Multiple Word Write 8-bit Cycle Timing Measurement
22
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory 32-bit Read on 16-bit External Bus
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to CSn assert time
tADs
tHCLK
-
-
ns
CSn assert to AD transition time
tADd1
-
tHCLK × (WST1 + 1)
-
ns
AD transition to CSn deassert time
tADd2
-
tHCLK × (WST1 + 2)
-
ns
AD hold from CSn deassert time
tADh
tHCLK
-
-
ns
tRDpwL
-
tHCLK × ((2 × WST1) + 3)
-
ns
tRDd
-
-
3
ns
CSn assert to DQMn assert delay time
tDQMd
-
-
1
ns
DA setup to AD transition time
tDAs1
15
-
-
ns
DA to RDn deassert time
tDAs2
tHCLK + 12
-
-
ns
DA hold from AD transition time
tDAh1
0
-
-
ns
DA hold from RDn deassert time
tDAh2
0
-
-
ns
RDn assert time
CSn to RDn delay time
tADs
tADd1
tADd2
tADh
AD
CSn
WRn
tRDd
tRDh
tRDpwl
RDn
DQMn
tDQMh
tDQMd
tDAs1
tDAh1
tDAs2
tDAh2
DA
WAIT
Figure 10. Static Memory Multiple Word Read 16-bit Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
23
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory 32-bit Write on 16-bit External Bus
Parameter
Symbol
Min
Typ
Max
Unit
AD setup to WRn assert time
tADs
tHCLK – 3
-
-
ns
WRn/DQMn deassert to AD transition time
tADd
-
-
tHCLK + 6
ns
AD hold from WRn deassert time
tADh
tHCLK × 2
-
-
ns
CSn hold from WRn deassert time
tCSh
7
-
-
ns
tWRd
CSn to WRn assert delay time
-
-
2
ns
WRn assert time
tWRpwL
-
tHCLK × (WST1 + 1)
-
ns
WRn deassert time
tWRpwH
-
-
(tHCLK × 2) + 14
ns
tDQMd
-
-
1
ns
DQMn assert time
tDQMpwL
-
tHCLK × (WST1 + 1)
-
ns
DQMn deassert time
tDQMpwH
-
-
(tHCLK × 2) + 7
ns
WRn / DQMn deassert to DA transition time
tDAh1
tHCLK
-
-
ns
WRn / DQMn assert to DA valid time
tDAV
-
-
8
ns
CSn to DQMn assert delay time
tADs
tADd
tADh
AD
CSn
tWRd
tWRpwL
WRn
tWRpwL
tCSh
tWRpwH
RDn
tDQMd
tDQpwL
DQMn
tDQpwL
tDQpwH
tDAV
tDAh
tDAV
tDAh
DA
WAIT
Figure 11. Static Memory Multiple Word Write 16-bit Cycle Timing Measurement
24
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Burst Read Cycle
Parameter
Symbol
Min
Typ
Max
Unit
CSn assert to Address 1 transition time
tADd1
-
tHCLK × (WST1 + 1)
-
ns
Address assert time
tADd2
-
tHCLK × (WST2 + 1)
-
ns
AD transition to CSn deassert time
tADd3
-
tHCLK × (WST1 + 2)
-
ns
AD hold from CSn deassert time
tADh
tHCLK
-
-
ns
tRDd
-
-
3
ns
CSn to RDn delay time
CSn to DQMn assert delay time
tDQMd
-
-
1
ns
DA setup to AD transition time
tDAs1
15
-
-
ns
DA setup to CSn deassert time
tDAs2
tHCLK + 12
-
-
ns
DA hold from AD transition time
tDAh1
0
-
-
ns
DA hold from RDn deassert time
tDAh2
0
-
-
ns
Note:
These characteristics are valid when the Page Mode Enable (Burst Mode) bit is set. See the User's Guide for details.
tADs
tADd1
tADd2
tADd2
tADh
tADd3
AD
CSn
WRn
tRDd
RDn
DQMn
tDQMd
tDAh1
tDAh1
tDAh1
tDAh2
DA
tDAs1
tDAs1
tDAs1
tDAs2
WAIT
Figure 12. Static Memory Burst Read Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
25
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Burst Write Cycle
Parameter
Symbol
Min
AD setup to WRn assert time
tADs
tHCLK − 3
ns
AD hold from WRn deassert time
tADh
tHCLK × 2
ns
WRN/DQMn deassert to AD transition time
tADd
CSn hold from WRn deassert time
tCSh
CSn to WRn assert delay time
tWRd
CSn to DQMn assert delay time
tDQMd
DQMn assert time
tDQpwL
DQMn deassert time
tDQpwH
WRn assert time
tWRpwL
WRn deassert time
tWRpwH
WRn/DQMn deassert to DA transition time
tDAh
WRn/DQMn assert to DA valid time
tDAv
Note:
Typ
Max
Unit
tHCLK + 6
ns
7
ns
2
ns
1
ns
tHCLK × (WST1 + 1)
ns
(tHCLK × 2) + 14
ns
tHCLK × (WST1 + 11)
ns
(tHCLK × 2) + 7
ns
tHCLK
ns
8
ns
These characteristics are valid when the Page Mode Enable (Burst Mode) bit is set. See the User's Guide for details.
tADs
tADd
tADh
AD
CSn
tWRpwL
WRn
tCSh
tWRpwH
tWRd
RD
tDQMd
tDQpwL
DQMn
tDQpwH
tDAv
tDAh
DA
WAIT
Figure 13. Static Memory Burst Write Cycle Timing Measurement
26
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Single Read Wait Cycle
Parameter
Symbol
Min
Typ
Max
Unit
CSn assert to WAIT time
tWAITd
-
-
tHCLK × (WST1-2)
ns
WAIT assert time
tWAITpw
tHCLK × 2
-
tHCLK × 510
ns
tCSnd
tHCLK × 3
-
tHCLK × 5
ns
WAIT to CSn deassert delay time
AD
CSn
WRn
RDn
DQMn
DA
WAIT
tWAITd
tWAITpw
tCSnd
Figure 14. Static Memory Single Read Wait Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
27
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Single Write Wait Cycle
Parameter
Symbol
Min
Typ
Max
Unit
tWRd
tHCLK × 2
-
tHCLK × 4
ns
CSn assert to WAIT time
tWAITd
-
-
tHCLK × (WST1-2)
ns
WAIT assert time
tWAITpw
tHCLK × 2
-
tHCLK × 510
ns
tCSnd
tHCLK × 3
-
tHCLK × 5
ns
WAIT to WRn deassert delay time
WAIT to CSn deassert delay time
AD
CSn
tWRd
WRn
RDn
DQMn
DA
tWAITd
tWAITpw
tCSnd
WAIT
Figure 15. Static Memory Single Write Wait Cycle Timing Measurement
28
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Static Memory Turnaround Cycle
Parameter
CSnX deassert to CSnY assert time
Symbol
Min
Typ
Max
Unit
tBTcyc
-
tHCLK × (IDCY+1)
-
ns
Notes: 1. X and Y represent any two chip select numbers.
2. IDCY occurs on read-to-write and write-to-read.
3. IDCY is honored when going from a asynchronous device (CSx) to a synchronous device (/SDCSy).
tBTcyc
AD
CSnX
CSnY
WRn
RDn
DQMn
DA
WAIT
Figure 16. Static Memory Turnaround Cycle Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
29
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Ethernet MAC Interface
Min
Parameter
Typ
Max
Symbol
10 Mbit
mode
100 Mbit
mode
10 Mbit
mode
100 Mbit
mode
10 Mbit
mode
100 Mbit
mode
Unit
TXCLK cycle time
tTX_per
-
-
400
40
-
-
ns
TXCLK high time
tTX_high
140
14
200
20
260
26
ns
TXCLK low time
tTX_low
140
14
200
20
260
26
ns
TXCLK to signal transition delay time
tTXd
0
0
10
10
25
25
ns
TXCLK rise/fall time
tTXrf
-
-
-
-
5
5
ns
RXCLK cycle time
tRX_per
-
-
400
40
-
-
ns
RXCLK high time
tRX_high
140
14
200
20
260
26
ns
RXCLK low time
tRX_low
140
14
200
20
260
26
ns
tRXs
10
10
-
-
-
-
ns
RXDVAL / RXERR hold time
tRXh
10
10
-
-
-
-
ns
RXCLK rise/fall time
tRXrf
-
-
-
-
5
5
ns
RXDVAL / RXERR setup time
MDC cycle time
tMDC_per
-
-
400
400
-
-
ns
MDC high time
tMDC_high
160
160
-
-
-
-
ns
MDC low time
tMDC_low
160
160
-
-
-
-
ns
MDC rise/fall time
tMDCrf
-
-
-
-
5
5
ns
MDIO setup time (STA sourced)
tMDIOs
10
10
-
-
-
-
ns
MDIO hold time (STA sourced)
tMDIOh
10
10
-
-
-
-
ns
MDC to MDIO signal transition delay time
(PHY sourced)
tMDIOd
-
-
-
-
300
300
ns
STA - Station - Any device that contains an IEEE 802.11 conforming Medium Access Control (MAC) and physical layer
(PHY) interface to the wireless medium.
PHY - Ethernet physical layer interface.
30
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
tTX_high
tTX_low
TXCLK
TXD[3:0]/
TXEN/
TXERR
tTXd
tTX_per
tRX_low
tRX_high
RXCLK
tRXh
RXD[3:0]/
RXDVAL/
RXERR
tRX_per
tRXs
MDC
MDIO
(Sourced
by STA)
tMDC_high
tMDC_low
tMDIOs
tMDIOh
tMDC_per
MDC
MDIO
(Sourced
by PHY)
tMDIOd
Figure 17. Ethernet MAC Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
31
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Audio Interface
The following table contains the values for the timings of each of the SPI modes.
Parameter
Symbol
Min
Typ
Max
Unit
SCLK cycle time
tclk_per
-
tspix_clk
-
ns
SCLK high time
tclk_high
-
(tspix_clk) / 2
-
ns
SCLK low time
tclk_low
-
(tspix_clk) / 2
-
ns
SCLK rise/fall time
tclkrf
1
-
8
ns
Data from master valid delay time
tDMd
-
-
3
ns
Data from master setup time
tDMs
20
-
-
ns
Data from master hold time
tDMh
40
-
-
ns
Data from slave setup time
tDSs
20
-
-
ns
Data from slave hold time
tDSh
40
-
-
ns
Note:
32
The tspix_clk is programmable by the user.
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Texas Instruments’ Synchronous Serial Format
tclk_per
tclk_high
tclkrf
SCLK
tclk_low
SFRM
SSPTXD/
SSPRXD
MSB
LSB
4 to 16 bits
Figure 18. TI Single Transfer Timing Measurement
Microwire
tclk_high
tclk_per
tclkrf
SCLK
tclk_low
SFRM
SSPTXD
LSB
MSB
8-bit control
SSPRXD
0
MSB
LSB
4 to 16 bits output data
Figure 19. Microwire Frame Format, Single Transfer
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
33
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Motorola SPI
tclk_per
tclk_high
tclkrf
SCLK
(SPO=0)
tclk_low
SCLK
(SPO=1)
tDMs
SSPTXD
(master)
tDMh
MSB
LSB
tDMd
tDSs
SSPRXD
(slave)
tDSh
MSB
LSB
SFRM
Figure 20. SPI Format with SPH=1 Timing Measurement
34
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Inter-IC Sound - I2S
Parameter
Symbol
Min
Typ
Max
Unit
SCLK cycle time
tclk_per
-
ti2s_clk
-
ns
SCLK high time
tclk_high
-
(ti2s_clk) / 2
-
ns
SCLK low time
tclk_low
-
(ti2s_clk) / 2
-
ns
SCLK rise/fall time
tclkrf
1
4
8
ns
SCLK to LRCLK assert delay time
tLRd
-
-
3
ns
Hold between SCLK assert then LRCLK deassert
or
Hold between LRCLK deassert then SCLK assert
tLRh
0
-
-
ns
SDI to SCLK deassert setup time
tSDIs
12
-
-
ns
SDI from SCLK deassert hold time
tSDIh
0
-
-
ns
SCLK assert to SDO delay time
tSDOd
-
-
9
ns
SDO from SCLK assert hold time
tSDOh
1
-
-
ns
Note:
ti2s_clk is programmable by the user.
tclk_per
tclk_low
tclk_high
tclkrf
SCLK
tLRd
tLRh
LRCLK
tSDIs
tSDIh
SDI
tSDOd
tSDOh
SDO
Figure 21. Inter-IC Sound (I2S) Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
35
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
AC’97
Parameter
Symbol
Min
Typ
Max
Unit
ABITCLK input cycle time
tclk_per
-
81.4
-
ns
ABITCLK input high time
tclk_high
36
-
45
ns
ABITCLK input low time
tclk_low
ns
36
-
45
tclkrf
2
-
6
ns
ASDI setup to ABITCLK falling
ts
10
-
-
ns
ASDI hold after ABITCLK falling
th
10
-
-
ns
ASDI input rise/fall time
trfin
2
-
6
ns
ABITCLK rising to ASDO / ASYNC valid, CL = 55 pF
tco
2
-
15
ns
trfout
2
-
6
ns
ABITCLK input rise/fall time
ASYNC / ASDO rise/fall time, CL = 55 pF
tclk_high
tclk_low
tclk_per
ABITCLK
tclkrf
tclkrf
th
ts
trfin
ASDI
ASDO
trfout
tco
tco
tco
ASYNC
trfout
trfout
Figure 22. AC ‘97 Configuration Timing Measurement
36
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
LCD Interface
Parameter
Symbol
Min
Typ
Max
Unit
SPCLK rise/fall time
tclkr
2
-
8
ns
SPCLK rising edge to control signal transition time
tCD
-
-
3
ns
SPCLK rising edge to data transition time
tDD
-
-
10
ns
Data valid time
tDv
tSPCLK
-
-
ns
tclkrf
tclkrf
SPCLK
HSYNC/
V_CSYNC/
BLANK/
BRIGHT
tCD
tDD
P [17:0]
tDv
Figure 23. LCD Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
37
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
ADC
Parameter
Resolution
Comment
Value
No missing codes
Range of 0 to 3.3 V
50K counts (approximate)
Integral non-linearity
Units
0.01%
Offset error
±15
Full scale error
mV
0.2%
Maximum sample rate
ADIV = 0
ADIV = 1
3750
925
Samples per second
Samples per second
Channel switch settling time
ADIV = 0
ADIV = 1
500
2
μs
ms
120
μV
Noise (RMS) - typical
Note:
ADIV refers to bit 16 in the KeyTchClkDiv register.
ADIV = 0 means the input clock to the ADC module is equal to the external 14.7456 MHz clock divided by 4.
ADIV = 1 means the input clock to the ADC module is equal to the external 14.7456 MHz clock divided by 16.
61A8
0000
FFFF
9E58
0
Vref/2
Vref
A/D Converter Transfer Function
(approximately ±25,000 counts)
Figure 24. ADC Transfer Function
Using the ADC:
This ADC has a state-machine based conversion engine that automates the conversion process. The initiator for a
conversion is the read access of the TSXYResult register by the CPU. The data returned from reading this register
contains the result as well as the status bit indicating the state of the ADC. However, this peripheral requires a delay
between each successful conversion and the issue of the next conversion command, or else the returned value of
successive samples may not reflect the analog input. Since the state of the ADC state machine is returned through the
same channel used to initiate the conversion process, there must be a delay inserted after every complete conversion.
Note that reading TSXYResult during a conversion will not affect the result of the ongoing process.
The following is a recommended procedure for safely polling the ADC from software:
1. Read the TSXYResult register into a local variable to initiate a conversion.
2. If the value of bit 31 of the local variable is '0' then repeat step 1.
3. Delay long enough to meet the maximum sample rate as shown above.
4. Mask the local variable with 0xFFFF to remove extraneous data.
5. If signed mode is used, do a sign extend of the lower halfword.
6. Return the sampled value.
38
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
JTAG
Parameter
Symbol
Min
Max
Units
TCK clock period
tclk_per
100
-
ns
TCK clock high time
tclk_high
50
-
ns
TCK clock low time
tclk_low
50
-
ns
TMS / TDI to clock rising setup time
tJPs
20
-
ns
Clock rising to TMS / TDI hold time
tJPh
45
-
ns
JTAG port clock to output
tJPco
-
30
ns
JTAG port high impedance to valid output
tJPzx
-
30
ns
JTAG port valid output to high impedance
tJPxz
-
30
ns
TMS
TDI
tclk_per
tclk_high
tJPs
tJPh
tclk_low
TCK
tJPzx
tJPco
tJPxz
TDO
Figure 25. JTAG Timing Measurement
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
39
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
272 Pin TFBGA Package Outline
272 TFBGA Diagram
Figure 26. 272 Pin TFBGA Diagram
D
0.600 REF
E1
E
D1
e
e
ddd
A
A2
c
A1
Øb
ddd
40
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table R. 272 Pin Diagram Dimensions
dimension in mm
dimension in inches
Symbol
MIN
NOM
MIN
NOM
MAX
A
1.35
1.40
1.45
0.053
0.055
0.057
A1
0.23
0.28
0.33
0.009
0.011
0.013
A2
0.65
0.70
0.75
0.026
0.028
0.030
b
0.35
0.40
0.45
0.014
0.016
0.018
c
0.21
0.26
0.31
0.0083
0.0102
0.0122
D
13.95
14.00
14.05
0.549
0.551
0.553
D3
12.75
12.80
12.85
0.502
0.504
0.506
E
13.95
14.00
14.05
0.549
0.551
0.553
E3
12.75
12.80
12.85
0.502
0.504
0.506
e
0.75
0.80
0.85
0.030
0.031
0.033
ddd
Note:
MAX
0.10
0.004
1. Controlling Dimension: Millimeter.
2. Primary Datum C and seating plane are defined by the spherical crowns of the solder balls.
3. Dimension b is measured at the maximum solder ball diameter, parallel to Primary Datum C.
4. There shall be a minimum clearance of 0.25 mm between the edge of the solder ball and the body edge.
5. Reference Document: JEDEC MO-151, BAL-2
272 Pin TFBGA Pinout (Bottom View)
The following table shows the 272 pin TFBGA pinout. (For better understanding, compare the coordinates on the x and
y axis on Figure 27, "272 Pin TFBGA Pinout", on page 42 with Figure 26, "272 Pin TFBGA Diagram", on page 40.
• VDD_core is vddc.
• VDD_ring is vddr.
• GND_core is gndc.
• GND_ring is gndr.
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
41
DS667F2
Figure 27. 272 Pin TFBGA Pinout
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
U
NC
NC
P[8]
P[4]
P[1]
DA[6]
DA[3]
AD[10]
DA[0]
TDO
NC
SCLK[1]
SSPRX[1]
INT[1]
RTSn
USBm[1]
NC
U
T
NC
NC
V_CSYNC
P[7]
P[2]
DA[7]
AD[11]
AD[9]
DSRn
TMS
gndr
SFRM[1]
INT[2]
INT[0]
USBp[1]
NC
NC
T
R
P[9]
HSYNC
P[6]
P[5]
P[0]
AD[14]
DA[4]
DA[1]
DTRn
TDI
BOOT[0]
ASYNC
USBm[0]
ABITCLK
USBp[0]
R
P SPCLK
P[10]
P[11]
P[3]
AD[15]
AD[13]
AD[12]
DA[2]
AD[8]
TCK
BOOT[1]
EEDAT
GRLED
RDLED
GGPIO[2]
RXD[1]
RXD[2]
P
N
P[16]
P[15]
P[13]
P[12]
DA[5]
vddr
vddr
vddr
vddr
EECLK
ASDO
CTSn
RXD[0]
TXD[0]
TXD[1]
TXD[2]
N
P[17]
gndr
gndr
vddc
vddc
gndr
gndr
ROW[6]
ROW[4]
ROW[1]
ROW[0]
ROW[3]
ROW[2]
M
gndr
ROW[7]
ROW[5]
PLL_GND
XTALI
XTALO
L
gndc
vddc
COL[4]
PLL_VDD
COL[2]
COL[1]
COL[0]
K
gndc
vddc
vddr
COL[5]
COL[6]
CSn[0]
COL[3]
J
gndc
gndr
vddr
EGPIO[8]
PRSTn
COL[7]
RSTOn
H
P[14]
M BRIGHT
AD[0]
L
DA[9]
AD[2]
AD[1]
DA[8]
BLANK
gndr
K
AD[4]
DA[12]
DA[10]
DA[11]
vddr
gndr
gndc
J
AD[6]
DA[14]
AD[7]
DA[13]
vddr
vddc
gndc
H DA[18]
DA[20]
DA[19]
DA[16]
vddr
vddc
gndc
G DQMn[0]
CASn
DA[21]
AD[22]
vddr
gndr
AD[5]
gndr
gndr
gndr
vddc
vddc
gndr
DA[15]
AD[21]
DA[17]
vddr
vddr
vddr
MIIRXD[0]
DA[28]
HGPIO[4]
AD[16]
MDC
MIIRXD[2]
F
RASn
DQMn[1] DQMn[2]
SDCSn[1] SDCSn[0] DQMn[3]
gndc
gndc
gndr
E SDCSn[2] SDWEN
DA[22]
AD[3]
D SDCSn[3]
DA[23]
SDCLK
DA[24] HGPIO[7] HGPIO[6]
C AD[23]
DA[26]
CSn[3]
DA[25]
AD[24]
AD[19]
HGPIO[5]
WRn
MDIO
B AD[25]
CSn[2]
CSn[6]
AD[20]
DA[30]
AD[18]
HGPIO[3]
AD[17]
RXCLK
A CSn[1]
CSn[7]
SDCLKEN DA[31]
DA[29]
DA[27]
HGPIO[2]
RDn
5
6
7
8
1
2
3
4
SSPTX[1] PWMOUT
EGPIO[9] EGPIO[10] EGPIO[11] RTCXTALO RTCXTALI
EGPIO[7] EGPIO[5] ADC_GND EGPIO[6]
sYm
sYp
F
EGPIO[4]
EGPIO[3]
sXp
sXm
E
RXERR
MIITXD[3] EGPIO[12] EGPIO[1]
EGPIO[0]
Ym
Yp
D
TXCLK
MIITXD[0]
EGPIO[13]
TRSTn
Xp
Xm
C
USBp[2]
ARSTn
ADC_VDD
B
A
TXERR
EGPIO[2]
CLD
MIIRXD[1] MIITXD[2]
TXEN
FGPIO[5] EGPIO[15]
MIIRXD[3] RXDVAL MIITXD[1]
CRS
FGPIO[7]
FGPIO[0]
WAITn
USBm[2]
ASDI
12
13
14
15
16
17
9
10
G
11
42
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Copyright 2010 Cirrus Logic (All Rights Reserved)
1
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Pin List
The following Thin-profile Fine-pitch Ball Grid Array (TFBGA) ball assignment table is sorted in order of ball.
Ball
Signal
Ball
Signal
Ball
Signal
Ball
Signal
A1
CSn[1]
E1
SDCSn[2]
J10
gndc
P1
SPCLK
A2
CSn[7]
E2
SDWEN
J12
vddc
P2
P[10]
A3
SDCLKEN
E3
DA[22]
J13
vddr
P3
P[11]
A4
DA[31]
E4
AD[3]
J14
COL[5]
P4
P[3]
A5
DA[29]
E5
DA[15]
J15
COL[6]
P5
AD[15]
A6
DA[27]
E6
AD[21]
J16
CSn[0]
P6
AD[13]
A7
HGPIO[2]
E7
DA[17]
J17
COL[3]
P7
AD[12]
A8
RDn
E8
vddr
K1
AD[4]
P8
DA[2]
A9
MIIRXD[3]
E9
vddr
K2
DA[12]
P9
AD[8]
A10
RXDVAL
E10
vddr
K3
DA[10]
P10
TCK
A11
MIITXD[1]
E11
MIIRXD[0]
K4
DA[11]
P11
BOOT[1]
A12
CRS
E12
TXERR
K5
vddr
P12
EEDAT
A13
FGPIO[7]
E13
EGPIO[2]
K6
gndr
P13
GRLED
A14
FGPIO[0]
E14
EGPIO[4]
K8
gndc
P14
RDLED
A15
WAITn
E15
EGPIO[3]
K9
gndc
P15
GGPIO[2]
A16
USBm[2]
E16
sXp
K10
gndc
P16
RXD[1]
A17
ASDI
E17
sXm
K12
vddc
P17
RXD[2]
B1
AD[25]
F1
RASn
K13
COL[4]
R1
P[9]
B2
CSn[2]
F2
SDCSn[1]
K14
PLL_VDD
R2
HSYNC
B3
CSn[6]
F3
SDCSn[0]
K15
COL[2]
R3
P[6]
B4
AD[20]
F4
DQMn[3]
K16
COL[1]
R4
P[5]
B5
DA[30]
F5
AD[5]
K17
COL[0]
R5
P[0]
B6
AD[18]
F6
gndr
L1
DA[9]
R6
AD[14]
B7
HGPIO[3]
F7
gndr
L2
AD[2]
R7
DA[4]
B8
AD[17]
F8
gndr
L3
AD[1]
R8
DA[1]
B9
RXCLK
F9
vddc
L4
DA[8]
R9
DTRn
B10
MIIRXD[1]
F10
vddc
L5
BLANK
R10
TDI
B11
MIITXD[2]
F11
gndr
L6
gndr
R11
BOOT[0]
B12
TXEN
F12
EGPIO[7]
L12
gndr
R12
ASYNC
B13
FGPIO[5]
F13
EGPIO[5]
L13
ROW[7]
R13
SSPTX[1]
B14
EGPIO[15]
F14
ADC_GND
L14
ROW[5]
R14
PWMOUT
B15
USBp[2]
F15
EGPIO[6]
L15
PLL_GND
R15
USBm[0]
B16
ARSTn
F16
sYm
L16
XTALI
R16
ABITCLK
B17
ADC_VDD
F17
sYp
L17
XTALO
R17
USBp[0]
C1
AD[23]
G1
DQMn[0]
M1
BRIGHT
T1
NC
C2
DA[26]
G2
CASn
M2
AD[0]
T2
NC
C3
CSn[3]
G3
DA[21]
M3
DQMn[1]
T3
V_CSYNC
C4
DA[25]
G4
AD[22]
M4
DQMn[2]
T4
P[7]
C5
AD[24]
G5
vddr
M5
P[17]
T5
P[2]
C6
AD[19]
G6
gndr
M6
gndr
T6
DA[7]
C7
HGPIO[5]
G12
gndr
M7
gndr
T7
AD[11]
C8
WRn
G13
EGPIO[9]
M8
vddc
T8
AD[9]
DS667F2
Copyright 2010 Cirrus Logic (All Rights Reserved)
43
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
44
Ball
Signal
Ball
Signal
Ball
Signal
Ball
Signal
C9
MDIO
G14
EGPIO[10]
M9
vddc
T9
DSRn
C10
MIIRXD[2]
G15
EGPIO[11]
M10
gndr
T10
TMS
C11
TXCLK
G16
RTCXTALO
M11
gndr
T11
gndr
C12
MIITXD[0]
G17
RTCXTALI
M12
ROW[6]
T12
SFRM[1]
C13
CLD
H1
DA[18]
M13
ROW[4]
T13
INT[2]
C14
EGPIO[13]
H2
DA[20]
M14
ROW[1]
T14
INT[0]
C15
TRSTn
H3
DA[19]
M15
ROW[0]
T15
USBp[1]
C16
Xp
H4
DA[16]
M16
ROW[3]
T16
NC
C17
Xm
H5
vddr
M17
ROW[2]
T17
NC
D1
SDCSn[3]
H6
vddc
N1
P[14]
U1
NC
D2
DA[23]
H8
gndc
N2
P[16]
U2
NC
D3
SDCLK
H9
gndc
N3
P[15]
U3
P[8]
D4
DA[24]
H10
gndc
N4
P[13]
U4
P[4]
D5
HGPIO[7]
H12
gndr
N5
P[12]
U5
P[1]
D6
HGPIO[6]
H13
vddr
N6
DA[5]
U6
DA[6]
D7
DA[28]
H14
EGPIO[8]
N7
vddr
U7
DA[3]
D8
HGPIO[4]
H15
PRSTn
N8
vddr
U8
AD[10]
D9
AD[16]
H16
COL[7]
N9
vddr
U9
DA[0]
D10
MDC
H17
RSTOn
N10
vddr
U10
TDO
D11
RXERR
J1
AD[6]
N11
EECLK
U11
NC
D12
MIITXD[3]
J2
DA[14]
N12
ASDO
U12
SCLK[1]
D13
EGPIO[12]
J3
AD[7]
N13
CTSn
U13
SSPRX[1]
D14
EGPIO[1]
J4
DA[13]
N14
RXD[0]
U14
INT[1]
D15
EGPIO[0]
J5
vddr
N15
TXD[0]
U15
RTSn
D16
Ym
J6
vddc
N16
TXD[1]
U16
USBm[1]
D17
Yp
J8
gndc
N17
TXD[2]
U17
NC
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
The following section focuses on the EP9307 pin signals
from two viewpoints - the pin usage and pad
characteristics, and the pin multiplexing usage. The first
table (Table S) is a summary of all the EP9307 pin
signals. The second table (Table T) illustrates the pin
signal multiplexing and configuration options.
Table S is a summary of the EP9307 pin signals, which
illustrates the pad type and pad pull type (if any). The
symbols used in the table are defined as follows. (Note: A
blank box means Not Applicable (NA) or, for Pull Type,
No Pull (NP).)
Under the Pad Type column:
• A - Analog pad
• P - Power pad
• G - Ground pad
• I - Pin is an input only
• I/O - Pin is input/output
• 4mA - Pin is a 4mA output driver
• 8mA - Pin is an 8mA output driver
• 12mA - Pin is an 12mA output driver
See the text description for additional information about
bi-directional pins.
Under the Pull Type Column:
•
•
DS667F2
PU - Resistor is a pull up to the RVDD supply
PD - Resistor is a pull down to the RGND supply
Copyright 2010 Cirrus Logic (All Rights Reserved)
45
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table S. Pin Descriptions (Continued)
.
Table S. Pin Descriptions
Pin Name
TCK
Block
Pad
Type
Pull
Type
JTAG
I
PD
TDI
JTAG
I
PD
TDO
JTAG
4ma
-
TMS
TRSTn
BOOT[1:0]
XTALI
JTAG
I
PD
I
PD
JTAG reset
I
PD
Boot mode select in
PLL
A
-
Main oscillator input
PLL
A
-
Main oscillator output
PLL
P
-
Main oscillator power, 1.8V
GND_PLL
PLL
G
-
Main oscillator ground
RTCXTALI
RTC
A
-
RTC oscillator input
RTC
A
-
RTC oscillator output
EBUS
4ma
-
SRAM Write strobe out
4ma
-
WAITn
EBUS
I
PU
EBUS
8ma
-
Shared Address bus out
EBUS
8ma
PU
Shared Data bus in/out
CSn[3:0]
EBUS
4ma
PU
Chip select out
CSn[7:6]
EBUS
4ma
PU
Chip select out
8ma
-
SDRAM
8ma
-
SDRAM clock out
SDCLKEN
SDRAM
8ma
-
SDRAM clock enable out
SDCSn[3:0]
SDRAM
4ma
-
SDRAM chip selects out
SDRAM
8ma
-
Data Terminal Ready output
-
Ready to send
TXD1
UART2
4ma
-
Transmit/IrDA output
RXD1
UART2
I
PU
TXD2
UART3
4ma
-
Transmit
RXD2
UART3
I
PU
Receive
PU
Management data input/output
Receive/IrDA input
MDC
EMAC
4ma
MDIO
EMAC
4ma
Management data clock
RXCLK
EMAC
I
PD
Receive clock in
MIIRXD[3:0]
EMAC
I
PD
Receive data in
RXDVAL
EMAC
I
PD
Receive data valid
RXERR
EMAC
I
PD
Receive data error
TXCLK
EMAC
4ma
PU
Transmit clock in
MIITXD[3:0]
EMAC
I
PD
Transmit data out
TXEN
EMAC
4ma
PD
Transmit enable
TXERR
EMAC
4ma
PD
Transmit error
CRS
EMAC
I
PD
Carrier sense
CLD
EMAC
I
PU
Collision detect
GRLED
LED
12ma
-
RDLED
LED
12ma
-
Green LED
EECLK
EEPROM
4ma
PU
EEPROM/Two-wire Interface clock
EEDAT
EEPROM
4ma
PU
EEPROM/Two-wire Interface data
ABITCLK
AC97
8ma
PD
AC97 bit clock
ASYNC
AC97
8ma
PD
AC97 frame sync
ASDI
AC97
I
PD
AC97 Primary input
ASDO
AC97
8ma
PU
AC97 output
ARSTn
AC97
8ma
-
AC97 reset
SCLK1
SPI1
8ma
PD
SPI bit clock
SFRM1
SPI1
8ma
PD
SPI Frame Clock
SSPRX1
SPI1
I
PD
SPI input
Red LED
Shared data mask out
SDCLK
RASn
-
4ma
SRAM Wait in
DA[31:0]
EBUS
4ma
UART1
SRAM Read/OE strobe out
AD[25:0]
DQMn[3:0]
UART1
RTSn
JTAG test mode select
JTAG
EBUS
DTRn
Description
JTAG data out
System
RDn
Pull
Type
JTAG data in
VDD_PLL
WRn
Pad
Type
JTAG clock in
XTALO
RTCXTALO
Block
Pin Name
Description
SDRAM RAS out
CASn
SDRAM
8ma
-
SDRAM CAS out
SDWEn
SDRAM
8ma
-
SDRAM write enable out
P[17:0]
Raster
4ma
PU
Pixel data bus out
SPCLK
Raster
12ma
PU
Pixel clock in/out
HSYNC
Raster
8ma
PU
Horizontal synchronization/ line pulse out
V_CSYNC
Raster
8ma
PU
Vertical or composite synchronization/frame
pulse out
SSPTX1
SPI1
8ma
-
BLANK
Raster
8ma
PU
Composite blanking signal out
INT[2:0]
INT
I
PD
External interrupts
BRIGHT
Raster
4ma
-
PWM brightness control out
PRSTn
Syscon
I
PU
Power on reset
PWMOUT
PWM
8ma
Pulse width modulator output
RSTOn
Syscon
4ma
-
SPI output
User Reset in out - open drain
Xp, Xm
ADC
A
-
Touchscreen ADC X axis
EGPIO[15]
GPIO
I/O, 4ma
PU
Enhanced GPIO
Yp, Ym
ADC
A
-
Touchscreen ADC Y axis
EGPIO[13:0]
GPIO
I/O, 4ma
PU
Enhanced GPIO
sXp, sXm
ADC
A
-
Touchscreen ADC X axis feedback
FGPIO[7, 5, 0]
GPIO
I/O, 8ma
PU
GPIO
GPIO
I/O, 8ma
PU
GPIO
sYp, sYm
ADC
A
-
Touchscreen ADC Y axis feedback
GGPIO[2]
VDD_ADC
ADC
P
-
Touchscreen ADC power, 3.3V
HGPIO[7:2]
GPIO
I/O, 8ma
PU
GND_ADC
ADC
G
-
Touchscreen ADC ground
vddc
Power
P
-
COL[7:0]
Key
8ma
PU
Key matrix column inputs
vddr
Power
P
-
Digital power, 3.3V
Ground
G
-
Digital ground
Ground
G
-
Digital ground
ROW[7:0]
Key
8ma
PU
Key matrix row outputs
gndc
USBp[2:0]
USB
A
-
USB positive signals
gndr
USBm[2:0]
USB
A
-
USB negative signals
TXD0
UART1
4ma
-
Transmit out
RXD0
UART1
I
PU
Receive in
CTSn
UART1
I
PU
Clear to send/transmit enable
DSRn
UART1
I
PU
Data set ready/Data Carrier Detect
46
Copyright 2010 Cirrus Logic (All Rights Reserved)
GPIO
Digital power, 1.8V
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Table T illustrates the pin signal multiplexing and configuration options.
Table T. Pin Multiplex Usage Information
DS667F2
Physical
Pin Name
Description
Multiplex signal name
COL[7:0]
GPIO
GPIO Port D[7:0]
ROW[7:0]
GPIO
GPIO Port C[7:0]
EGPIO[0]
Ring Indicator Input
RI
EGPIO[1]
1Hz clock monitor
CLK1HZ
EGPIO[2]
DMA request
DMARQ
EGPIO[3]
HDLC Clock
HDLCCLK1
EGPIO[4]
I2S Transmit Data 1
SDO1
EGPIO[5]
I2S Receive Data 1
SDI1
EGPIO[6]
I2S Transmit Data 2
SDO2
EGPIO[7]
DMA Request 0
DREQ0
EGPIO[8]
DMA Acknowledge 0
DACK0
EGPIO[9]
DMA EOT 0
DEOT0
EGPIO[10]
DMA Request 1
DREQ1
EGPIO[11]
DMA Acknowledge 1
DACK1
EGPIO[12]
DMA EOT 1
DEOT1
EGPIO[13]
I2S Receive Data 2
SDI2
EGPIO[15]
Device active / present
DASP
ABITCLK
I2S Serial clock
SCLK
ASYNC
I2S Frame Clock
LRCK
ASDO
I2S Transmit Data 0
SDO0
ASDI
I2S Receive Data 0
SDI0
ARSTn
I2S Master clock
MCLK
SCLK1
I2S Serial clock
SCLK
SFRM1
I2S Frame Clock
LRCK
SSPTX1
I2S Transmit Data 0
SDO0
SSPRX1
I2S Receive Data 0
SDI0
Copyright 2010 Cirrus Logic (All Rights Reserved)
47
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Acronyms and Abbreviations
The following tables list abbreviations and acronyms
used in this data sheet.
Term
Term
Definition
OHCI
Open Host Controller Interface
PHY
Ethernet PHYsical layer interface
PIO
Programmed I/O
RISC
Reduced Instruction Set Computer
SDMI
Secure Digital Music Initiative
SDRAM
Synchronous Dynamic RAM
SPI
Serial Peripheral Interface
SRAM
Static Random Access Memory
STA
Station - Any device that contains an IEEE 802.11
conforming Medium Access Control (MAC) and physical
layer (PHY) interface to the wireless medium
TFT
Thin Film Transistor
TLB
Translation Lookaside Buffer
USB
Universal Serial Bus
Definition
ADC
Analog-to-Digital Converter
ALT
Alternative
AMBA
Advanced Micro-controller Bus Architecture
ATAPI
ATA Packet Interface
CODEC
COder / DECoder
CRC
Cyclic Redundancy Check
DAC
Digital-to-Analog Converter
DMA
Direct-Memory Access
EBUS
External Memory Bus
EEPROM Electronically Erasable Programmable Read Only Memory
EMAC
Ethernet Media Access Controller
FIFO
First In / First Out
FIQ
Fast Interrupt Request
FLASH
Flash memory
GPIO
General Purpose I/O
HDLC
High-level Data Link Control
I/F
Units of Measurement
Symbol
Unit of Measure
°C
degree Celsius
Hz
Hertz = cycle per second
Kbps
Kilobits per second
Interface
kbyte
Kilobyte
I2S
Inter-IC Sound
kHz
KiloHertz = 1000 Hz
IC
Integrated Circuit
Mbps
Megabits per second
ICE
In-Circuit Emulator
MHz
MegaHertz = 1,000 kHz
IDE
Integrated Drive Electronics
μA
microAmpere = 10-6 Ampere
IEEE
Institute of Electronics and Electrical Engineers
μs
microsecond = 1,000 nanoseconds = 10-6 seconds
IrDA
Infrared Data Association
mA
milliAmpere = 10-3 Ampere
IRQ
Standard Interrupt Request
ms
millisecond = 1,000 microseconds = 10-3 seconds
ISO
International Standards Organization
mW
milliWatt = 10-3 Watts
JTAG
Joint Test Action Group
ns
nanosecond = 10-9 seconds
LFSR
Linear Feedback Shift Register
pF
picoFarad = 10-12 Farads
MII
Media Independent Interface
V
Volt
W
Watt
MMU
Memory Management Unit
48
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
ORDERING INFORMATION
The order numbers for the device are:
EP9307-CRZ
EP9307-IRZ
0°C to +70°C
-40°C to +85°C
272 pin TFBGA
272 pin TFBGA
Lead Free
Lead Free
EP9307 — CRZ
Lead Material:
Z = Lead Free
Part Number
Product Line:
Embedded Processor
Note:
DS667F2
Package Type:
R = 272 pin TFBGA
Temperature Range:
C = Commercial
E = Extended Operating Version
I = Industrial Operating Version
Go to the Cirrus Logic Internet site at http://www.cirrus.com to find contact information for your local sales representative.
Copyright 2010 Cirrus Logic (All Rights Reserved)
49
EP9307
ARM9 SOC with Ethernet, USB, Display and Touchscreen
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find one nearest you go to www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to
change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the
time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this
information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document
is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade
secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the
information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such
as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY
OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS
AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES
OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT
MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, MaverickCrunch, MaverickKey, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Microwire is a trademark of National Semiconductor Corp. National Semiconductor is a registered trademark of National Semiconductor Corp.
Texas Instruments is a registered trademark of Texas Instruments, Inc.
Motorola and SPI are registered trademarks of Motorola, Inc.
LINUX is a registered trademark of Linus Torvalds.
50
Copyright 2010 Cirrus Logic (All Rights Reserved)
DS667F2
工商网监
湘ICP备2023018690号
