CSX750VCB13.500M-UT

PAGE DATE NO. 1/10 Messrs. SPECIFICATION PRODUCT NAME: VOLTAGE CONTROLLED CRYSTAL OSCILLATOR TYPE: CSX-750V MHz FREQUENCY: PARTS NO.: CITIZEN WATCH CO., LTD. 1-12, Honcho 6-chome, Tanashi-shi, Tokyo 188-8511 Japan Oscillator Technical section Crystal Devices Div. Telephone: 0424-68-4572 Fax : 0424-68-4666 PRODUCTS MARKETING GROUP Telephone: 0424-67-6214 Telex:2822-471/ Fax: 0424-67-8503 APPROVED CHECKED PREPARED SPECIFICATION I. NO. DATE PAGE 2/10 SCOPE This specification relates to the voltage controlled crystal oscillator to be supplied by CITIZEN WATCH CO., LTD. (following as CITIZEN) to . NOTICE 1.If something that is ambiguously defined or undefined in this specification happened, the customer and CITIZEN would discuss and take necessary steps by mutual consent. 2.Product test data can't be attached to this specification. 3.This product is not authorized for use as critical component in life support devices or systems. II. SPECIFICATION 1. ABSOLUTE MAXIMUM RATING CSX750VB/CSX750VC Parameter -0.5V to +7.0V Supply Voltage Vmax Storage Temperature Tstg -45°C to +90°C Output Current Iout Input Control Voltage Vc_m 10mA Max. -0.5V to Vdd +0.5V Solder Heat Resistance Tsol Max.240°C x Max.10 seconds x 2times Max.200°C x Max. 3 minutes Of The Outer Lead 2. OPERATING RANGE Parameter CSX750VB CSX750VC 3.3V±5% 5.0V±10% Supply Voltage Vdd Operating Temperature Topr Input Control Voltage Vc 0.0V to Vdd Output Load CL 30pF Max. -10°C to 70°C or -40°C to 85°C 3. FREQUENCY CHARACTERISTICS Parameter CSX750VB CSX750VC Stability (note1) dF0 Pullability (note2) Fpull ±90ppm Min. ±100ppm Min. Linearity Ldev ±15% Max. ±10% Max. Modulation Band Width Fmod ±50ppm Max. 10kHz Min. note1) Frequency Stability includes initial tolerance, temperature characteristics, input voltage characteristics, load characteristics, shock, vibration, reflow and 1st year aging. note2) Vc=1.65V±1.65V (CSX750VB) Vc=2.5V±2.0V (CSX750VC) SPECIFICATION NO. DATE PAGE 3/10 4. ELECTRICAL CHARACTERISTICS (Ta=25°C load=30pF Vc=Vdd/2) Parameter CSX750VB Conditions CSX750VC 4msec Max. Start Up Time (note) tosc Power Supply Current Idd No Load 11mA Max. 30mA Max. Disable Current Iinh No Load 5mA Max. 20mA Max. Rise Time tr 20% to 80%Vdd 5ns Max. Fall Time tf 80% to 20%Vdd 5ns Max. Duty Cycle duty 50%Vdd Output HIGH Voltage Voh Ioh = -0.8mA Output LOW Voltage Vol Iol = 3.2mA OE Input HIGH Voltage Vih Vdd x 0.7 Min. OE Input LOW Voltage Vil Vdd x 0.3 Max. Output Disable Time tpxz Output Enable Time tpzx 45% to 55% Vdd-0.4V Min. 0.4V Max. See 5. 100ns Max. 100ns Max. note) Vc must be kept ground level or left open when starting up. 5. THREE STATE OUTPUT OPERATION OE Input Clock Output HIGH or OPEN Active enable LOW High impedance disable Propagation delay time between tpxz:OE(HIGH to LOW) and OUTPUT(active level to high impedance) tpxz Clock Output tpzx:OE(LOW to HIGH) and OUTPUT(high impedance to active level) tpzx high impedance OE input HIGH or OPEN LOW NOTE: A disable clock output does not synchronize with OE, because internal quartz oscillator is continuous. SPECIFICATION NO. DATE PAGE 4/10 6. TEST CIRCUIT [CMOS LOAD] (30pF) Vdd [SUPPLY CURRENT] Vdd Test Point 6 5 4 Vdd OE OUT .01 to 0.1uF Vc 1 2 GND 3 6 5 4 Vdd OE OUT CL= 30pF .01 to 0.1uF 1.65V 1.65V GND GND Vc 1 2 [MEASUREMENT CONDITION] 1.Osilloscope Impedance:No less than 1Mohm Capacitance:No more than 5pF Band width:No less than 500MHz The length of GND lead of the probe should be as short as possible. 2.The CL includes the probe capacitance. 3.Grounding should be single point grounding. 4.Supply impedance should be as low as possible. 0V to 90%Vdd rise time is no less than 150us 5.Use the ammeter that internal impedance is small. 7. OUTPUT WAVEFORM [CMOS LOAD] (30pF) tf tr 80%Vdd 50%Vdd 20%Vdd Th T DUTY=Th/T GND 3 SPECIFICATION NO. DATE 8. ENVIRONMENTAL AND MECHANICAL CHARACTERISTICS The following are our reliability test conditions. Item Conditions Shock MIL-STD-883E 2002.3B Vibration MIL-STD-883E 2007.2A Gross Leak Leak rate less than 50ppm atm cc /sec of Air Fine Leak Leak rate less than 0.01ppm atm cc /sec of Herium PAGE 5/10 SPECIFICATION NO. DATE PAGE 6/10 III. DIMENSIONS AND MARKING (UNIT mm) Manufucturer's Name Frequency CTZ VBBL 32.7680 017105 Type Production Lot Number SPECIFICATION NO. DATE PAGE 7/10 IV. TAPE AND REEL PACKAGING 1. TAPING SPECIFICATION Subject to EIA 481A & JIS C 0806 (1) Tape Dimensions Material of the Carrier Tape : PA-PET conductive coat Material of the Cover Tape : PE A-PET conducutive coat (2) Reel Dimensions Material of the Reel : PS Symbol Dimension(mm) A 254+/-2 N 100+/-1 W1 17.5+/-1.0 W2 21.5+/-1.0 SPECIFICATION NO. DATE (3) Packing Item Tape Leader Tape Trailer 2. INNER CARTON Cover Tape Empty Pockets Cover Tape Empty Pockets Empty Space Min. 500 mm Min. 20 Pockets Min. 0 mm Min. 40 mm PAGE 8/10 SPECIFICATION NO. DATE PAGE 9/10 3. OUTER CARTON 4. MARKING (1) Marking Labels are affixed to reel , inner carton and outer carton. Reel Marking is consist of: (2) Each label contains the following information. * Parts name or type * Frequency * Quantity * Manufucturing Date or symbol * Manufucturer's name or symbol * Others(if necessary) 5. QUANTITY 2000 pcs/reel 6. STORAGE ENVIRONMENT * Storage the reel at normal temperature and humidity * Open the packing just before using. * Do not expose the sun. * Do not storage with some erosive chemicals. * Nothing is allowed to put on the reel or carton to prevent mechanical damage. 7. HANDLING * Handle with care to prevent the damege of tape, reel and products. SPECIFICATION NO. DATE PAGE 10/10 V. NOTES 1. HANDLING (ELECTROSTATIC DISCHARGES) This device is made with CMOS circuitry. Please take precautions to prevent damage due to electrical static discharge. (SHOCK RELIABILITY) This device contains a quartz crystal, so please do not give too much shock or vibration. An automatic insersion is available, however, the internal quartz crystal might be damaged in case that too much shock or vibration is given by machine condition. Be sure to check your machine condition in advance. (CLEANING) Since, depending on the cleaning conditions,there is a possibility of damage being caused to the Crystal Osillator,do not fail to test and confirm the results beforehand,using your company's cleaning conditions. (TEMPERATURE AND HUMIDITY) We recomend to store and use device under normal temperature and humidity. When this device is used in high humidity applications, there is a potential problem with condensation. As with other IC's, please take precautions to prevent condensation. 2. CIRCUIT DESIGNS (POWER LINES) We recomend placing a 0.01 to 0.1uF capacitor between VDD and GND to obtain stable operation and protect against power line ripple . VDD and GND pattern should be as wide as possible. (OE INPUT LINE) When OE pin is not used, please connect it to VDD. (OUTPUT LINE) As a long output line may cause irregular output, please take care to design that output line is as short as possible, and also keep high level signal source away from this device. (STARTING UP) Vc must be kept ground level or left open when starting up.