476602000

C&K TP Series Tiny Pushbutton Switches Features/Benefits • Subminiature size—capable of • A Pushbutton • • • • switching 1 AMP Vertical & right angle terminations PC & panel mount models Snap-in front panel mounting available Epoxy terminal seal-compatible with bottom wash cleaning RoHS compliant models available Typical Applications • Telecommunications and networking equipment • Computers and peripherals • Instrumentation and controls Models Available Specifications Materials CONTACT RATING: B contact material: 0.4 VA max. @ 20 V AC or DC max. Q contact material: 1 AMP @ 120 V AC or 28 V DC. See page A-17 for additional ratings. CASE: Glass filled nylon 6/6, flame retardant, heat stabilized or diallyl phthalate (DAP), (UL 94V-0). ELECTRICAL LIFE: TP11, TP21 MODELS: 60,000 make-and-break cycles at full load. TP12 MODELS: 30,000 cycles. CAP & FRAME: Nylon, black standard. PLUNGER: Thermoplastic polyester (UL 94V-0). BUSHING: Brass, nickel plated. CONTACT RESISTANCE: Below 20 mΩ typ. initial @ 2-4 V DC, 100 mA, for both silver and gold plated contacts. INSULATION RESISTANCE: 109Ω min. HOUSING: Stainless steel. SWITCH SUPPORT: Brass, matte-tin plated. END CONTACTS: B contact material: Copper alloy, with gold plate over nickel plate. Q contact material: Coin silver, silver plated. See page A-21 for additional contact materials. DIELECTRIC STRENGTH: 1000 Vrms min. @ sea level. OPERATING TEMPERATURE: –30ºC to 85ºC. SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). NOTE: Any models supplied with Q, B, P, R or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. CENTER CONTACT & ALL TERMINALS: B contact material: Copper alloy, with gold plate over nickel plate. Q contact material: Copper alloy, silver plated. See page A-17 for additional contact materials. TERMINAL SEAL: Epoxy. Refer to soldering and cleaning in Technical Data Chapter HARDWARE: Nut & Locking Ring: Brass nickel plated. Lockwasher: Steel, nickel plated. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages A-13 thru A-18. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function TP11 SPST Off-Mom. TP12 SPDT On-Mom. TP21 DPST Off-Mom. Actuator or Bushing SH .155" high plunger, threaded, .220" high bushing, flat SH8 .155" high plunger, unthreaded, .220" high bushing, round SH9 .155" high plunger, unthreaded, .220" high bushing, flat J81 Snap-in with frame LT .215" high plunger, threaded, .310" high bushing, flat LT9 .215" high plunger, unthreaded, .310" high bushing, flat MS9 .130" high plunger, .020" high bushing, round Terminations Right angle, PC thru-hole A C PC Thru-hole Z Solder lug AV Vertical right angle, PC thru-hole V3 Vertical mount, v-bracket W Wire wrap Contact Material B Gold K Gold, tin-lead P Gold, matte-tin Q Silver G Gold over silver L Gold over silver, tin lead R Gold over silver, matte-tin Seal E Epoxy Cap Color 2 Black NONE Models with no cap 1 White Frame Color 2 Black NONE Models with no frame Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–13 www.ittcannon.com C&K TP Series Tiny Pushbutton Switches SWITCH FUNCTION Pushbutton A NO. POLES MODEL NO. SWITCH FUNCTION POS. 1 POS. 2 CONNECTED TERMINALS POS. 1 POS. 2 C&K marking on opposite side C&K marking on opposite side TP11 OFF MOM. OPEN 1-3 TP12 ON MOM. 2-1 2-3 SCHEMATIC SPST SP SPDT SPDT Omit terminal 2 for TP11 models. Terminal Nos. For Reference Only Part number shown: TP12SHZQE DP TP21 OFF MOM. OPEN 1-3,4-6 DPST DPST Terminal Nos. For Reference Only Part number shown: TP21SHZQE MOM. = Momentary All models with all options when ordered with G, L, Q or R contact material. CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR BUSHING J81 FRAME COLOR SNAP-IN WITH FRAME OPTION CODE PANEL MOUNTING CAP COLOR 2 BLACK 1 WHITE OPTION CODE 2 NONE FRAME COLOR BLACK No Frame Color (J80 option) Cap and Frame Finish: matte. Other colors available, consult Customer Service Center. NOTE: Available with Z, C, or W terminations. NOTE: Caps & frames available separately, see page A-18. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–14 www.ittcannon.com C&K TP Series Tiny Pushbutton Switches A SH8 .155" HIGH PLUNGER, SH9 .155" HIGH PLUNGER, .155" HIGH PLUNGER, LT MS9 .215" HIGH PLUNGER, .220" HIGH BUSHING, .220" HIGH BUSHING, .220" HIGH BUSHING, .310" HIGH BUSHING, THREADED, FLAT UNTHREADED UNTHREADED, FLAT THREADED LT9 .130" HIGH PLUNGER .215" HIGH PLUNGER, .310" HIGH BUSHING, UNTHREADED Standard with Z, C, W terminations. Not available with Z terminations. Standard with A, AV, V3 terminations. † Subtract .016 (0,41) for models with A, AV or V3 terminations. NOTE: Caps available for plunger options, see page A-18. PANEL MOUNTING 10-48 BUSHING Without locking ring 1/4 IN. BUSHING With standard locking ring Without locking ring With standard locking ring NOTE: One mounting nut, locking ring and lockwasher supplied standard with 10-48 threaded bushings (two nuts with 1/4-40 bushings). Optional mounting nut and locking ring styles and finishes available separately, see section “Technical Data and Additional Hardware”. TERMINATIONS C Z PC THRU-HOLE SP W SOLDER LUG WIRE WRAP DP SP DP SP DP PC MOUNTING Omit center holes for TP11 models Not available with MS9 bushing or K, L, P, or R contact material. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–15 www.ittcannon.com Pushbutton SH C&K TP Series Tiny Pushbutton Switches TERMINATIONS Pushbutton A A RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TP12SH9ABE SPDT A TP11 Models: omit terminal 2. TP11 Models: omit hole 2. RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TP21SH9ABE DPST AV VERTICAL RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TP12SH9AVBE SPDT TP11 Models: omit hole 2. TP11 Models: omit terminal 2. NOTE: Terminal bend radii and lead-in manufacturing option. AV VERTICAL RIGHT ANGLE, PC THRU-HOLE PC MOUNTING TP21SH9AVBE DPST NOTE: Terminal bend radii and lead-in manufacturing option. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–16 www.ittcannon.com C&K TP Series Tiny Pushbutton Switches TERMINATIONS A VERTICAL MOUNT, V-BRACKET Pushbutton V3 PC MOUNTING TP11 Models: omit hole 2. TP12SH9V3BE SPDT TP11 Models: omit terminal 2. V3 VERTICAL MOUNT, V-BRACKET PC MOUNTING TP21SH9V3BE DPST CONTACT MATERIAL OPTION CODE B K P Q G L R CONTACT MATERIAL RoHS COMPLIANT * RoHS COMPATIBLE * YES YES GOLD 1 SILVER 4,5 GOLD OVER SILVER 2,3 TERMINAL PLATING RATINGS GOLD 1 NO YES TIN-LEAD 6 YES YES MATTE-TIN 7 YES YES SILVER 5 YES YES GOLD 3 NO YES TIN-LEAD 6 YES YES MATTE-TIN 7 LOW LEVEL/DRY CIRCUIT 0.4 VA MAX. @ 20 V AC OR DC MAX. POWER 1 AMP @ 120 V AC OR 28 V DC. LOW LEVEL/DRY CIRCUIT OR POWER 0.4 VA MAX @ 20 V AC OR DC MAX. OR 1 AMP @ 120 V AC OR 28 V DC. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. 2 END CONTACTS: Coin silver, with gold plate over nickel plate. 3 CENTER CONTACTS & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. 4 END CONTACTS: Coin silver, silver plated. 5 CENTER CONTACT & ALL TERMINALS: Copper alloy, silver plated. 6 TERMINALS: Copper alloy, with tin-lead alloy over nickel plate. 7 TERMINALS: Copper alloy, with matte-tin over nickel plate. NOTE: Any models supplied with P, R, Q, B or G contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. All models with all options when ordered with R, G, L or Q contact material. B contact material standard with A, AV, V3 & W terminations. Q contact material standard with C & Z terminations P, R, K, L contact materials not available with Z terminations. SEAL E EPOXY SEAL Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–17 www.ittcannon.com C&K TP Series Tiny Pushbutton Switches AVAILABLE HARDWARE Pushbutton A Cap, .100" DIA. Plungers Cap, .100" DIA. Plungers (Recommended for S9 plunger) Cap, .100" DIA. Plungers PART NO. PART NO. PART NO. 508101000 WHITE 508102000 BLACK 538701000 WHITE 538702000 BLACK 465801000 WHITE 465802000 BLACK Material: Nylon Finish: Gloss Material: Nylon Finish: Gloss Material: Nylon Finish: Gloss Cap, .120" DIA. Plungers Cap, .120" DIA. Plungers Cap, J81 option only PART NO. PART NO. PART NO. PART NO. 708901000 WHITE 708902000 BLACK 801801000 WHITE 801802000 BLACK 484601000 WHITE 484602000 BLACK 798201000 WHITE 798202263 BLACK Material: Nylon Finish: Gloss Material: Nylon Finish: Gloss Material: Nylon Finish: Gloss Material: Nylon Finish: Matte NOTE: Additional nuts, locking rings and lockwashers available separately, see section “Technical Data and Additional Hardware”. Other cap colors available, consult Customer Service Center. Frames snap into panel opening and are independent from switch mounting. Accurate positioning of the PC mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. Available in two basic styles and four panel thicknesses .047-.125 in. Material: Nylon. Finish: Matte. TYPICAL APPLICATION .047" (1,19) PANEL THK. .062" (1,57) PANEL THK. .090" (2,29) PANEL THK. .125" (3,18) PANEL THK. PART NO. PART NO. PART NO. PART NO. 432502263 432602263 432702263 432802263 BLACK PANEL MOUNTING For part numbers 432502263, 432602263 For part numbers 432702263, 432802263 .005 R. .495 ± .505 (0,13) (12,57 ± 12,83) MAX. TYP. .005 R. (0,13) MAX. TYP. .595 ± .605 (15,11 ± 15,37) Panel Inserts .495 ± .505 (12,57 ± 12,83) .620 ± .625 (15,75 ± 15,88) Above frames (part nos. 432XXXXXX) are also available with insert which accepts LED for indicator light assembly. Order insert separately from frame. Blank insert panel (without hole for LED) also available. LED not included. PANEL INSERT WITH HOLE FOR LED BLANK PANEL INSERT WITHOUT HOLE FOR LED PART NO. PART NO. 894902000 476602000 BLACK Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change A–18 www.ittcannon.com