SD04H1BD

SD Series Low Profile DIP Switches Features/Benefits • Low profile design saves space •  Thru-hole and surface mount models controls •  Logic switching for computers and peripherals •  Function controlling for numerous applications Specifications H DIP •  Tape and reel packaging available •  Sealed with top tape •  RoHS compliant Typical Applications Address switch for industrial •  CONTACT RATING: PACKAGING: Thru-hole switches supplied in rigid dispensing tubes in full-tube quantities only: this may effect order quantity. Surface mount switches available in tape and reel packaging by added ‘R’ to end of part number; 1,000 pieces per reel. Switch position 1 denotes pin number 1. All switch actuators in ‘OFF’ position, Carry: 100 mA @ 50 V DC max. standard. Switch: 0.1 mA @ 5 V DC min to 100 mA @ 25 V DC max. Materials SWITCH FUNCTION: SPST - 2, 3, 4, 5, 6, 7, 8, 9, 10 & 12 positions MECHANICAL AND ELECTRICAL LIFE: 2,000 make-and-break cycles at full load, each circuit. CASE & COVER: (PPA), flame retardant (UL 94V-0) CONTACT RESISTANCE: Below 50 milliohms typ. initial CONTACTS: BeCu with gold plate. TERMINALS: Bright tin-plated brass. @ 2-4 V DC, 100mA. ACTUATOR: Nylon, flame retardant (UL 94V-0) INSULATION RESISTANCE: 109 ohms min. TERMINAL SEAL: All terminals insert molded. DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between adjacent terminals. TAPE SEAL: Polyimide. STORAGE TEMPERATURE: -40°C to 85°C. OPERATING TEMPERATURE: -40°C to 85°C. OPERATING FORCE: 100-700g inital. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. How To Order The Build-A Switch concept allows you to mix and match options to create the switch you need. Below is a complete listing of options shown in catalog. To order, simply select desired option from each category and place in the appropriate box. S D Number of Positions SD02 SD07 SD03 SD08 SD04 SD09 SD05 SD10 SD06 SD12 Packaging (None) Tubes R Tape and Reel Actuator H0 Flush Actuator “OFF” position H1 Extended Actuator “OFF” position H2 Flush Actuator “ON” position H3 Extended Actuator “ON” position Terminations S Gull wing (None) PC ThruHole Process Seal (None) Tape seal D No tape seal Contact Material B Gold 10µ IN B1 Gold 30µ IN * * Consult factory for availability Dimensions are shown: Inch (mm) Specifications and dimensions subject to change 9 January 2018 H–13 www.ckswitches.com SD Series Low Profile DIP Switches Sealed Flush Actuator – With Top Tape, Thru-hole Terminals Process sealed - withstands soldering and cleaning processes ROHS PART NUMBER DIP H DIM. 'A' SEE CHART .027 (0,70) ACTUATOR TRAVEL ON .263 (6,68) 1 2 3 4 5 6 7 8 .142 (3,62) ORIENTATION MARK PEELABLE TAPE SEAL SD02H0B SD03H0B SD04H0B SD05H0B SD06H0B SD07H0B SD08H0B SD09H0B SD10H0B SD12H0B .300 TYP. (7,6) Ø.038 (0,97) TYP. .100 (2,54) TYP. .168 TYP. (4,27) .315 TYP. (8,00) NO. POS. DIM. ‘A’ QUANTITY PER TUBE 2 .258 (6,55) 85 3 .358 (9,09) 60 4 .458 (11,63) 45 5 .558 (14,17) 40 6 .658 (16,71) 30 7 .758 (19,25) 25 8 .858 (21,79) 25 9 .958 (24,33) 20 10 1.058 (26,87) 20 12 1.258 (31,95) 15 Schematic .023 TYP. (0,60) STANDOFF .059 TYP. (1,50) .126 TYP. (3,20) .100 TYP. (2,54) .022 TYP. (0,55) .010 TYP. (0,25) SPST .325 TYP. (8,25) Table applicable to “H0” and “H2” actuator options. Sealed Flush Actuator – With Top Tape, Surface Mount Terminals RoHS NO. QUANTITY PER TUBE PART NUMBER POS. DIM. ‘A’ .027 (0,70) ACTUATOR TRAVEL DIM. 'A' SEE CHART ON .243 TYP. (6,17) .435 MIN. (11,05) .263 (6,68) 1 2 3 4 5 6 7 8 .142 (3,62) ORIENTATION MARK .160 (4,06) WITH TAPE PEELABLE TAPE SEAL .100 (2,54) TYP. .044 MIN. (1,12) .315 TYP. (8,00) SD02H0SB SD03H0SB SD04H0SB SD05H0SB SD06H0SB SD07H0SB SD08H0SB SD09H0SB SD10H0SB SD12H0SB 2 .258 (6,55) 85 3 .358 (9,09) 60 4 .458 (11,63) 45 5 .558 (14,17) 40 6 .658 (16,71) 30 7 .758 (19,25) 25 8 .858 (21,79) 25 9 .958 (24,33) 20 10 1.058 (26,87) 20 12 1.258 (31,95) 15 Schematic .010 TYP. (0,25) STANDOFF .010 TYP. (0,25) .300 (7,62) .100 TYP. (2,54) .022 TYP. (0,55) SPST .390 (9,91) Table applicable to “H0” and “H2” actuator options. Sealed Extended Actuator – With Top Tape, Thru-hole Terminals .027 (0,70) ACTUATOR TRAVEL DIM. 'A' SEE CHART ON .263 (6,68) 1 2 3 4 5 6 7 ORIENTATION MARK PEELABLE TAPE SEAL .142 (3,62) .168 TYP. (4,30) .300 TYP. (7,6) Ø.038 (0,97) TYP. .100 (2,54) TYP. .315 TYP. (8,00) H1 Actuator 0.010 TYP. (0,25) .023 TYP. (0,60) STANDOFF .059 TYP. (1,50) 8 RoHS NO. QUANTITY PART NUMBER POS. DIM. ‘A’ PER TUBE .022 TYP. (0,55) .126 TYP. (3,20) .100 TYP. (2,54) .010 TYP. (0,25) .325 TYP. (8,25) SD02H1B SD03H1B SD04H1B SD05H1B SD06H1B SD07H1B SD08H1B SD09H1B SD10H1B SD12H1B 2 .258 (6,55) 85 3 .358 (9,09) 60 4 .458 (11,63) 45 5 .558 (14,17) 40 6 .658 (16,71) 30 7 .758 (19,25) 25 8 .858 (21,79) 25 9 .958 (24,33) 20 10 1.058 (26,87) 20 12 1.258 (31,95) 15 Schematic SPST Table applicable to “H1” and “H3” actuator options. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change 9 January 2018 H–14 www.ckswitches.com SD Series Low Profile DIP Switches Sealed Extended Actuator – With Top Tape, Surface Mount Terminals RoHS NO. QUANTITY PART NUMBER POS. DIM. ‘A’ PER TUBE 2 .258 (6,55) 85 3 .358 (9,09) 60 4 .458 (11,63) 45 5 .558 (14,17) 40 6 .658 (16,71) 30 7 .758 (19,25 25 8 .858 (21,79) 25 9 .958 (24,33) 20 10 1.058 (26,87) 20 12 1.258 (31,95) 15 ON .243 TYP. (6,17) .435 MIN. (11,05) .263 (6,68) 1 2 3 4 5 6 7 ORIENTATION MARK PEELABLE TAPE SEAL Schematic .010 TYP. (0,25) STANDOFF .022 TYP. (0,55) 8 .142 (3,62) .100 (2,54) TYP. .044 MIN. (1,12) .170 (4,31) WITH TAPE .315 TYP. (8,00) .010 TYP. (0,25) .100 TYP. (2,54) H1 Actuator 0.010 TYP. (0,25) .300 (7,62) .390 (9,91) SPST Table applicable to “H1” and “H3” actuator options. TAPE & REEL PACKAGING – SURFACE MOUNT OPTIONS ONLY RoHS NO. QUANTITY PER REEL PART NUMBER POS. DIM. ‘A’ .079 (2,00) SD02H0SBR SD03H0SBR SD04H0SBR SD05H0SBR SD06H0SBR SD07H0SBR SD08H0SBR SD09H0SBR SD10H0SBR SD12H0SBR .057 (4,00) 2 .258 (6,55) 1000 3 .358 (9,09) 1000 4 .458 (11,63) 1000 5 .558 (14,17) 1000 6 .658 (16,71) 1000 7 .758 (19,25 1000 8 .858 (21,79) 1000 9 .958 (24,33) 1000 10 1.058 (26,87) 1000 12 1.258 (31,95) 1000 DIM ‘P’ SEE CHART DIM ‘D’ SEE CHART .069 (1,75) .061 DIA (1,55) DIM ‘C’ SEE CHART DIM ‘B’ SEE CHART DIM ‘G’ SEE CHART Schematic DIM ‘A’ SEE CHART SPST ELONGATED HOLES ON SD07-SD12 ONLY Table applicable to “H0” and “H2” actuator options. FEED DIRECTION SWITCH NO. SD02 SD03 SD04 SD05 SD06 SD07 SD08 SD09 SD10 SD12 DIM ’A’ POCKET LENGTH @ BOTTOM .413(10,5) .406(10,3) .429(10,9) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) DIM ’B’ POCKET LENGTH @ BOTTOM .315(8,0) .406(10,3) .476(12,1) .602(15,3) .701(17,8) .803(20,4) .854(21,7) 1.028(26,1) 1.055(26,8) 1.303(33,1) DIM ’C’ TAPE WIDTH DIM ’D’ POCKET DEPTH DIM ’G’ SPROCKET HOLE SPACING DIM ’P’ PITCH BETWEEN POCKETS .630(16,0) .630(16,0) .954(24,0) .954(24,0) .954(24,0) 1.260(32,0) 1.732(44,0) 1.732(44,0) 1.732(44,0) 1.732(44,0) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) N/A N/A N/A N/A N/A 1.118(28,4) 1.591(40,4) 1.591(40,4) 1.591(40,4) 1.591(40,4) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) Reel Information Outside diameter 13.00 (333,0) Pilot hole .512 (13,0) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change 9 January 2018 H–15 H DIP SD02H1SB SD03H1SB SD04H1SB SD05H1SB SD06H1SB SD07H1SB SD08H1SB SD09H1SB SD10H1SB SD12H1SB .027 (0,70) ACTUATOR TRAVEL DIM. 'A' SEE CHART www.ckswitches.com