SD12H0SBR

SD Series Low Profile DIP Switches Features/Benefits • Low profile design saves space • Thru-hole and surface mount models • Tape and reel packaging available • Sealed with top tape • RoHS compliant Typical Applications • Address switch for industrial controls • Logic switching for computers and peripherals • Function controlling for numerous applications H DIP Specifications SWITCH FUNCTION: SPST - 2, 3, 4, 5, 6, 7, 8, 9, 10 & 12 positions CONTACT RATING: Carry: 100 mA @ 50 V DC max. Switch: 0.1 mA @ 5 V DC min to 100 mA @ 25 V DC max. MECHANICAL AND ELECTRICAL LIFE: 2,000 make-and-break cycles at full load, each circuit. CONTACT RESISTANCE: Below 50 milliohms typ. initial @ 2-4 V DC, 100mA. INSULATION RESISTANCE: 109 ohms min. DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between adjacent terminals. STORAGE TEMPERATURE: -40°C to 85°C. OPERATING TEMPERATURE: -40°C to 85°C. OPERATING FORCE: 100-700g inital. PACKAGING: Thru-hole switches supplied in rigid dispensing tubes in full-tube quantities only: this may effect order quantity. Surface mount switches available in tape and reel packaging by added ‘R’ to end of part number; 1,000 pieces per reel. Switch position 1 denotes pin number 1. All switch actuators in ‘OFF’ position, standard. Materials CASE & COVER: Thru-hole: polyester (PBT). Surface mount: (PPA), flame retardant (UL 94V-0). ACTUATOR: Nylon, flame retardant (UL 94V-0) CONTACTS: BeCu with gold plate. TERMINALS: Bright tin-plated brass. TERMINAL SEAL: All terminals insert molded. TAPE SEAL: Polyimide. Note: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. How To Order Complete part numbers for SD Series are shown on pages H–11 through H–13. All switches supplied in “OFF” position in rigid dispensing tubes or tape and reel packaging. Build-A-Switch SD B Packaging (None) Tubes R Tape and Reel Actuator H0 Flush Actuator H1 Extended Actuator Terminals S Surface Mount (None) PC ThruHole Number of Positions SD02 SD07 SD03 SD08 SD04 SD09 SD05 SD10 SD06 SD12 Process Seal (None) tape seal D No tape seal Contact Material B Gold Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–11 www.ck-components.com SD Series Low Profile DIP Switches Sealed Flush Actuator – With Top Tape, Thru-hole Terminals Process sealed - withstands soldering and cleaning processes ROHS PART NUMBER NO. POS. 2 3 4 5 6 7 8 9 10 12 QUANTITY PER TUBE 85 60 45 40 30 25 25 20 20 15 H DIP .263 (6,68) 1 2 3 DIM. 'A' SEE CHART .027 (0,70) ACTUATOR TRAVEL Ø.038 (0,97) TYP. .300 TYP. (7,6) DIM. ‘A’ .258 (6,55) .358 (9,09) .458 (11,63) .558 (14,17) .658 (16,71) .758 (19,25 .858 (21,79) .958 (24,33) 1.058 (26,87) 1.258 (31,95) 4 5 6 7 8 .142 (3,62) ORIENTATION MARK PEELABLE TAPE SEAL .168 TYP. (4,30) .100 (2,54) TYP. .315 TYP. (8,00) SD02H0B SD03H0B SD04H0B SD05H0B SD06H0B SD07H0B SD08H0B SD09H0B SD10H0B SD12H0B Schematic .023 TYP. (0,60) STANDOFF .059 TYP. (1,50) .022 TYP. (0,55) .126 TYP. (3,20) .100 TYP. (2,54) .010 TYP. (0,25) .325 TYP. (8,25) SPST Sealed Flush Actuator – With Top Tape, Surface Mount Terminals DIM. 'A' SEE CHART .027 (0,70) ACTUATOR TRAVEL RoHS PART NUMBER .243 TYP. (6,17) .435 MIN. (11,05) NO. POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .258 (6,55) .358 (9,09) .458 (11,63) .558 (14,17) .658 (16,71) .758 (19,25 .858 (21,79) .958 (24,33) 1.058 (26,87) 1.258 (31,95) QUANTITY PER TUBE 85 60 45 40 30 25 25 20 20 15 .263 (6,68) 1 2 3 4 5 6 7 8 .142 (3,62) .160 (4,06) WITH TAPE .044 MIN. (1,12) .315 TYP. (8,00) .100 (2,54) TYP. ORIENTATION MARK PEELABLE TAPE SEAL SD02H0SB SD03H0SB SD04H0SB SD05H0SB SD06H0SB SD07H0SB SD08H0SB SD09H0SB SD10H0SB SD12H0SB Schematic .010 TYP. (0,25) STANDOFF .022 TYP. (0,55) .100 TYP. (2,54) .010 TYP. (0,25) .300 (7,62) .390 (9,91) SPST Sealed Extended Actuator – With Top Tape, Thru-hole Terminals DIM. 'A' SEE CHART .027 (0,70) ACTUATOR TRAVEL .263 (6,68) 1 2 3 4 5 6 7 8 .142 (3,62) Ø.038 (0,97) TYP. .300 TYP. (7,6) RoHS PART NUMBER NO. POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .258 (6,55) .358 (9,09) .458 (11,63) .558 (14,17) .658 (16,71) .758 (19,25 .858 (21,79) .958 (24,33) 1.058 (26,87) 1.258 (31,95) QUANTITY PER TUBE 85 60 45 40 30 25 25 20 20 15 ORIENTATION MARK .010 TYP. (0,25) PEELABLE TAPE SEAL .168 TYP. (4,30) .100 (2,54) TYP. .315 TYP. (8,00) SD02H1B SD03H1B SD04H1B SD05H1B SD06H1B SD07H1B SD08H1B SD09H1B SD10H1B SD12H1B Schematic .023 TYP. (0,60) STANDOFF .059 TYP. (1,50) .022 TYP. (0,55) .126 TYP. (3,20) .100 TYP. (2,54) .010 TYP. (0,25) .325 TYP. (8,25) SPST Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–12 www.ck-components.com SD Series Low Profile DIP Switches Sealed Extended Actuator – With Top Tape, Surface Mount Terminals RoHS PART NUMBER NO. POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .258 (6,55) .358 (9,09) .458 (11,63) .558 (14,17) .658 (16,71) .758 (19,25 .858 (21,79) .958 (24,33) 1.058 (26,87) 1.258 (31,95) QUANTITY PER TUBE 85 60 45 40 30 25 25 20 20 15 .010 TYP. (0,25) STANDOFF .100 TYP. (2,54) .010 TYP. (0,25) .300 (7,62) .390 (9,91) .010 TYP. (0,25) .263 (6,68) 1 2 3 4 5 6 7 8 .142 (3,62) .170 (4,31) WITH TAPE .044 MIN. (1,12) .315 TYP. (8,00) .100 (2,54) TYP. DIM. 'A' SEE CHART .027 (0,70) ACTUATOR .243 TYP. TRAVEL (6,17) .435 MIN. (11,05) SD02H1SB SD03H1SB SD04H1SB SD05H1SB SD06H1SB SD07H1SB SD08H1SB SD09H1SB SD10H1SB SD12H1SB Schematic H DIP ORIENTATION MARK PEELABLE TAPE SEAL .022 TYP. (0,55) SPST TAPE & REEL PACKAGING – SURFACE MOUNT OPTIONS ONLY .079 (2,00) .057 (4,00) DIM ‘P’ SEE CHART DIM ‘D’ SEE CHART RoHS PART NUMBER NO. POS. 2 3 4 5 6 7 8 9 10 12 DIM. ‘A’ .258 (6,55) .358 (9,09) .458 (11,63) .558 (14,17) .658 (16,71) .758 (19,25 .858 (21,79) .958 (24,33) 1.058 (26,87) 1.258 (31,95) QUANTITY PER REEL 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 .061 DIA (1,55) .069 (1,75) SD02H0SBR SD03H0SBR SD04H0SBR SD05H0SBR SD06H0SBR SD07H0SBR SD08H0SBR SD09H0SBR SD10H0SBR SD12H0SBR Schematic DIM ‘B’ SEE CHART DIM ‘C’ SEE CHART DIM ‘G’ SEE CHART DIM ‘A’ SEE CHART ELONGATED HOLES ON SD07-SD12 ONLY SPST FEED DIRECTION SWITCH NO. SD02 SD03 SD04 SD05 SD06 SD07 SD08 SD09 SD10 SD12 DIM ’A’ POCKET LENGTH @ BOTTOM .413(10,5) .406(10,3) .429(10,9) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) .406(10,3) DIM ’B’ POCKET LENGTH @ BOTTOM .315(8,0) .406(10,3) .476(12,1) .602(15,3) .701(17,8) .803(20,4) .854(21,7) 1.028(26,1) 1.055(26,8) 1.303(33,1) DIM ’C’ TAPE WIDTH .630(16,0) .630(16,0) .954(24,0) .954(24,0) .954(24,0) 1.260(32,0) 1.732(44,0) 1.732(44,0) 1.732(44,0) 1.732(44,0) DIM ’D’ POCKET DEPTH .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) .177(4,5) DIM ’G’ SPROCKET HOLE SPACING N/A N/A N/A N/A N/A 1.118(28,4) 1.591(40,4) 1.591(40,4) 1.591(40,4) 1.591(40,4) DIM ’P’ PITCH BETWEEN POCKETS .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) .472(12,0) Reel Information Outside diameter Pilot hole 13.00 (333,0) .512 (13,0) Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–13 www.ck-components.com