CLE130E

CLE135, CLE130E, CLE130W 940nm High Efficiency GaAs/AlGaAs IREDs ® Clairex July, 2005  UPGRADED SERIES 0.156 (3.96) 0.136 (3.45) 1.00 (25.4) min. Technologies, Inc. 0.100 (2.54) dia. 0.215 (5.46) 0.205 (5.21) CATHODE 0.165 (4.19) 0.145 (3.68) 0.190 (4.83) 0.176 (4.47) ANODE 0.025 (0.64) max. 0.050 (1.27) nom 0.019 (0.48) 0.016 (0.41) 0.147 (3.73) 0.137 (3.48) CLE135 0.130 (3.30) max 1.00 (25.4) min. 0.050 (1.27) max 0.213 (5.41) 0.207 (5.26) 0.100 (2.54) pin circle CATHODE 0.169 (4.29) 0.163 (4.14) ANODE 0.010 (0.25) nom 0.019 (0.48) 0.016 (0.41) 0.147 (3.73) 0.137 (3.48) C 5 CLE130E 0.165 (4.19) 0.145 (3.68) 0.156 (3.96) 0.136 (3.45) 1.00 (25.4) min. 0.100 (2.54) dia. 0.215 (5.46) 0.205 (5.21) CATHODE 0.190 (4.83) 0.176 (4.47) ANODE 0.025 (0.64) max. 0.010 (0.25) max 0.019 (0.48) 0.016 (0.41) 0.147 (3.73) 0.137 (3.48) ALL DIMENSIONS ARE IN INCHES (MILLIMETERS) CLE130W Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. REVISED 4/15/06 Clairex Technologies, Inc. Phone: 972-265-4900 1301 East Plano Parkway Fax: 972-265-4949 Plano, Texas 75074-8524 www.clairex.com CLE135, CLE130E, CLE130W 940nm High Efficiency GaAs/AlGaAs IREDs features • higher power output • cathode connected to case • TO-46 header with three lens options • different package styles provide flexible design options description The original Clairex CLE130 series has been upgraded. The new series features current state of the art GaAs/AlGaAs technology for increased quantum efficiency. The chip substrate is N type material resulting in the case being common to the cathode. The original configuration can still be supplied as a special order. Three different lens options are offered. Contact Clairex for other electrical and package options. ® Clairex  Technologies, Inc. absolute maximum ratings (TA = 25°C unless otherwise stated) storage temperature CLE135 and CLE130W ............................................................. -65°C to +150°C CLE130E ................................................................................... -40°C to +125°C operating temperature CLE135 and CLE130W ............................................................. -65°C to +125°C CLE130E ................................................................................... -40°C to +100°C lead soldering temperature(1) .........................................................................260°C continuous forward current(2) ....................................................................... 100mA peak forward current (1.0ms pulse width, 10% duty cycle)................................. 1A reverse voltage ................................................................................................... 5V (3) continuous power dissipation ................................................................... 200mW notes: 1. 0.06” (1.5mm) from the header for 5 seconds maximum. 2. Derate linearly 0.80mA/°C from 25°C free air temperature to TA = +125°C. 3. Derate linearly 1.60mW/°C from 25°C free air temperature to TA = +125°C. electrical characteristics (TA = 25°C unless otherwise noted) symbol parameter CLE130 Series VF IR λp BW tr, tf Forward voltage Reverse current Peak wavelength Spectral bandwidth Output rise and fall time min - typ 1.5 940 50 700 max 1.8 10 - units V µA nm nm ns test conditions IF = 100mA VR = 3V IF = 100mA IF = 20mA IF = 100mA CLE130E PO PO θHP Total output power Total output power Emission angle at half power points Total output power Total output power Emission angle at half power points 2.0 1.5 12.5 2.5 80 10 2.0 70 mW mW deg. mW mW deg. IF = 100mA IF = 20mA IF = 20mA IF = 100mA IF = 20mA IF = 20mA CLE130W PO PO θHP CLE135 PO Total output power 10 mW IF = 100mA Ee Irradiance(4) 2.0 mW/cm2 IF = 100mA Ee Irradiance(4) 0.4 0.5 mW/cm2 IF = 20mA θHP Emission angle at half power points 22 deg. IF = 20mA note: 4. Ee is a measure of irradiance (power/unit area) within a 0.444" (1.128cm) diameter area, centered on the mechanical axis of the device and spaced 2.54" (6.45cm) from the lens side of the tab. This is geometrically equivalent to a 10° cone. Clairex reserves the right to make changes at any time to improve design and to provide the best possible product. Clairex Technologies, Inc. Phone: 972-265-4900 1301 East Plano Parkway Fax: 972-265-4949 Plano, Texas 75074-8524 www.clairex.com