PLA192S

PLA192 Single Pole OptoMOS® Relays Load Voltage Load Current Max RON PLA192 600 150 22 Units V mA Ω Features • 5000VRMS Input/Output Isolation • Small 6 Pin DIP Package • Low Drive Power Requirements (TTL/CMOS Compatible) • No Moving Parts • High Reliability • Arc-Free With No Snubbing Circuits • No EMI/RFI Generation • Machine Insertable, Wave Solderable • 600 volt blocking Description The PLA192 is a 1-Form-A solid state relay that uses optically coupled relay technology to provide an enhanced 5000V isolation barrier between the input and output of the relay. The efficient MOSFET switches use Clares patented OptoMOS® architecture. The optically coupled input is controlled by a highly efficient GaAIAs infrared LED. Approvals • UL Approved to UL1577 • CSA Certified • Complies with EN60950 Ordering Information Applications • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment—Patient/Equipment Isolation • Security • Aerospace • Industrial Controls Part # PLA192 PLA192S PLA192STR Description 6 Pin Dip (50/Tube) 6 Pin Surface Mount (50/Tube) 6 Pin Surface Mount (1000/Reel) Pin Configuration PLA192 Pinout AC/DC Configuration + Control Ð Control Do Not Use 1 2 3 6 5 4 Load Do Not Use Load PLA192 Pinout DC Only Configuration + Control Ð Control Do Not Use 1 2 3 6 5 4 + Load Ð Load Switching Characteristics of Normally Open (Form A) Devices 10ms CONTROL + 90% LOAD 10%+ TON 10%+ TOFF DS-PLA192-R2.0 www.clare.com 1 PLA192 Absolute Maximum Ratings (@ 25˚ C) Parameter Min Typ Max Units 1501 50 1 5 8002 600 mW mA A V mW V Input Power Dissipation Input Control Current Peak (10ms) Reverse Input Voltage Total Power Dissipation Peak Blocking Voltage Isolation Voltage Input to Output (60 seconds) 5000 Operational Temperature -40 Storage Temperature -40 Soldering Temperature DIP Package Surface Mount Package (10 Seconds Max.) 1 2 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. VRMS +85 °C +125 °C +260 +220 °C °C Derate Linearly 1.33 mw/˚C Derate Linearly 6.67 mw/˚C Electrical Characteristics Parameter Conditions Symbol Min Typ Max Units Output Characteristics @ 25°C Load Current (Continuous) AC/DC Configuration DC Configuration Peak Load Current 10ms On-Resistance* AC/DC Configuration IL=150mA DC Configuration IL=220mA Off-State Leakage Current VL=600V Switching Speeds Turn-On IF=5mA, VL=10V Turn-Off IF =5mA, VL=10V Output Capacitance 50V; f=1MHz Input Characteristics @ 25°C Input Control Current IL=100mA Input Dropout Current Input Voltage Drop IF=5mA Reverse Input Voltage Reverse Input Current VR=5V Common Characteristics @ 25°C Input to Output Capacitance * IL IL ILPK RON ILEAK TON TOFF COUT IF IF VF VR IR CI/O 5 0.4 0.9 - 50 0.7 1.2 3 150 220 350 22 8 1 5 5 50 1.4 5 10 - mA mA mA Ω Ω µA ms ms pF mA mA V V µA pF Within 1 second of on time 2 www.clare.com Rev. 2.0 PLA192 PERFORMANCE DATA* PLA192 Typical LED Forward Voltage Drop (N=50 Ambient Temperature = 25°C) IF = 5mADC 35 30 PLA192 Typical On-Resistance Distribution (N=50 Ambient Temperature = 25°C) (Load Current = 150mADC; IF = 5mADC) 25 20 30 25 Device Count (N) 20 15 10 5 0 PLA192 Typical Blocking Voltage Distribution (N=50 Ambient Temperature = 25°C) Device Count (N) 25 20 15 10 5 0 1.25 1.26 1.27 1.28 1.29 Device Count (N) 15 10 5 0 18 18.25 18.5 18.75 19 19.25 700 710 720 730 740 750 LED Forward Voltage Drop (V) On-Resistance (Ω) Blocking Voltage (V) PLA192 Typical IF for Switch Operation (N=50 Ambient Temperature = 25°C) (Load Current = 150mADC) 25 25 20 PLA192 Typical IF for Switch Dropout (N=50 Ambient Temperature = 25°C) PLA192 Typical Turn-On Time (N=50 Ambient Temperature = 25°C) (Load Current = 100mADC; IF = 5mADC) 35 30 Device Count (N) Device Count (N) Device Count (N) 0.75 1.05 1.35 1.65 1.95 2.25 20 25 20 15 10 5 15 15 10 10 5 5 0 0.75 1.05 1.35 1.65 1.95 2.25 0 0 1.6 1.7 1.8 1.9 2.0 2.1 LED Current (mA) LED Current (mA) Turn-On (ms) PLA192 Typical Turn-Off Time (N=50 Ambient Temperature = 25°C) (Load Current = 100mADC; IF = 5mADC) 35 30 240 Load Current (mA) PLA192 Maximum Load Current vs. Temperature DC Configuration Device Count (N) 25 20 15 10 5 0 0.23 0.26 0.29 0.32 0.35 0.38 200 180 160 140 120 -40 -20 0 20 40 60 AC/DC Configuration 10mA 5mA On-Resistance (Ω) 220 10mA 5mA 80 100 120 18 16 14 12 10 8 6 4 2 0 PLA192 Typical On-Resistance vs. Temperature (Load Current = Max Rated at Temp.) DC Configuration IF=5mA IF=10mA -40 -20 0 20 40 60 80 100 Turn-Off (ms) Temperature (°C) Temperature (°C) 60 On-Resistance (Ω) PLA192 Typical On Resistance vs. Temp. Load Current=100mA Instantaneous 0.06 0.05 PLA192 Typical Leakage vs. Temperature (Measured across Pins 4 & 6) Blocking Voltage (VRMS) 50 Leakage (µA) 40 30 20 10 0 -40 -20 0 20 40 60 IF=5mA 0.04 0.03 0.02 0.01 0 -40 -20 0 20 40 60 80 100 80 100 120 770 760 750 740 730 720 710 700 PLA192 Typical Blocking Voltage vs. Temperature -40 -20 0 20 40 60 80 100 Temperature (°C) Temperature (°C) Temperature (°C) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. Rev. 2.0 www.clare.com 3 PLA192 PERFORMANCE DATA* 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 PLA192 Typical Turn-On vs. Temperature (Load Current = 100mADC) 1.0 PLA192 Typical Turn-Off vs. Temperature (Load Current = 100mADC) 0.9 0.8 PLA192 Typical LED Forward Voltage Dropout vs. Temperature LED Forward Voltage Drop (V) 1.8 1.6 IF =5mA Turn-Off (ms) Turn-On (ms) 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1.4 1.2 1.0 5mA -40 -20 0 20 40 60 80 100 120 0 -40 -20 0 20 40 60 80 100 0.8 -40 -20 0 20 40 60 80 100 120 Temperature (°C) Temperature (°C) Temperature (°C) PLA192 Typical Turn-On vs. LED Forward Current (Load Current = 150mADC) 3.0 2.7 2.4 PLA192 Typical Turn-Off vs. LED Forward Current (Load Current = 150mADC) 1.0 0.8 3.000 LED Current (mA) PLA192 Typical IF for Switch Operation vs. Temperature (Load Current = 100mADC) 0.7 2.500 2.000 1.500 1.000 0.500 0 -40 -20 0 20 40 60 80 100 Turn-On (ms) 2.1 1.8 1.5 1.2 0.9 0.6 0.3 0 0 5 10 15 20 25 30 35 40 45 50 Turn-On (ms) 0.6 0.5 0.4 0.3 0.2 0.1 0 0 5 10 15 20 25 30 35 40 Forward Current (mA) Forward Current (mA) Temperature (°C) 150 Load Current (mA) PLA192 Typical Load Current vs. Load Voltage (Ambient Temperature = 25°C) IF = 5mADC PLA192 Energy Rating Curve 1.2 1.0 Load Current (A) 0.8 0.6 0.4 0.2 0 10µs 100µs 1ms 10ms 100ms Time 1s 10s 100s 100 50 0 -50 -100 -150 -2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 2.5 Load Voltage (V) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com Rev. 2.0 MECHANICAL DIMENSIONS 6Pin DIP Through Hole (Standard) 7.620 – 0.254 (0.300 – 0.010) 3.302 – 0.051 (0.130 – 0.002) 8.382 – 0.381 (0.330 – 0.015) PC Board Pattern (Top View) 2.540 ± 0.127 6-0.800 DIA. (0.100 ± 0.005) (6-0.031 DIA.) 7.239 TYP (0.285 TYP) 6.350 – 0.127 (0.250 – 0.005) 6.350 ± 0.127 (0.250 ± 0.005) 7.620 ± 0.127 (0.300 ± 0.005) 0.254 TYP (0.010 TYP) 9.144 – 0.508 (0.360 – 0.020) 2.54 – 0.127 (0.100 – 0.005) 5.080 ± 0.127 (0.200 ± 0.005) 6Pin DIP Surface Mount (“S” Suffix) 7.620 – 0.254 (0.300 – 0.010) 3.302 – 0.051 (0.130 – 0.002) 0.254 – 0.0127 (0.010 – 0.0005) 4.445 – 0.127 (0.175 – 0.005) 0.635 – 0.127 (0.025 – 0.005) 8.382 – 0.381 (0.330 – 0.015) 2.54 – 0.127 (0.100 – 0.005) 9.525 – 0.254 (0.375 – 0.010) 6.35 – 0.127 (0.250 – 0.005) PC Board Pattern (Top View) 2.540 ± 0.127 (0.100 ± 0.005) 8.305 ± 0.127 (0.327 ± 0.005) 1.905 ± 0.127 (0.075 ± 0.005) 1.499 ± 0.127 0.457 – 0.076 (0.018 – 0.003) (0.059 ± 0.005) 8.382 ± 0.381 (0.330 ± 0.015) Tape and Reel Packaging for 6 Pin Power DIP Surface Mount Package 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) W = 16.30 MAX (0.642 MAX) B0 = 10.30 (0.406) Top Cover Tape Embossment Carrier K1 = 3.80 (0.150) K0 = 4.90 (0.193) Embossment P = 12.00 (0.472) A0 = 10.30 (0.406) User Direction of Feed Dimensions mm (inches) For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-PLA192-R2.0 ©Copyright 2003, Clare, Inc. OptoMOS® is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 1/29/03