CMX860E1

CML Microcircuits COMMUNICATION SEMICONDUCTORS CMX860 Telephone Signalling Transceiver D/860/7 April 2008 Features Applications • • • • • • • • • • • • • • • • V.23 & Bell 202 FSK Tx and Rx DTMF/Tones Transmit and Receive Line and Phone Complementary Drivers Call Progress Decoder Dual Tone Detection and Generation Simple 'C-BUS' Serial Interface Low Power Operation ‘Powersave’ Standby Mode 1.1 Least Cost Routers Vending Machines Internet Appliances Home Management Systems Remote Meter Reading Alarm Systems Cable TV Set-Top Boxes Advanced Feature Phones Brief Description The CMX860 is a flexible, low-power Telephone Signalling Transceiver IC, designed for use in a wide range of line-powered telephone equipment. The IC combines the functions of a DTMF encoder and decoder, V.23 / Bell 202 modulator and demodulator plus call progression circuitry with analogue switching between line and phone interfaces. Ring detection, local phone off-hook detection and a relay driver for line hook-switch operation are also provided under the control of 'C-BUS'. The ring and hook detectors operate whilst the remainder of the IC is powersaved, generating an interrupt to wake-up the host µC when further processing or signalling is required. All on-chip functions and switching arrangements are controlled via a serial bus ('C-BUS'). The CMX860 is designed to operate at 2.7V and utilises CML’s low power DTMF decoder and V.23 / Bell 202 modem technology. It is available in 28-pin SOIC (D1), TSSOP (E1) and SSOP (D6) packages. © 2008 CML Microsystems Plc Telephone Signalling Transceiver / Least Cost Router CMX860 CONTENTS Page Section 1.0 Features and Applications ..................................................................... 3 1.1 Brief Description ..................................................................................... 3 1.2 Block Diagram ......................................................................................... 5 1.3 Signal List ................................................................................................ 6 1.4 External Components............................................................................. 8 1.4.1 Ring Detector Interface ........................................................... 10 1.4.2 Hook Detector Interface .......................................................... 11 1.4.5 RESETN pin .............................................................................. 11 1.5 General Description.............................................................................. 12 1.5.1 Tx USART.................................................................................. 13 1.5.2 FSK Modulator ......................................................................... 14 1.5.3 Tx Filter and Equaliser ............................................................ 14 1.5.4 DTMF/Tones Generator ........................................................... 14 1.5.5 Tx Level Control and Output Drivers ..................................... 14 1.5.6 DTMF Decoder and Tone Detectors....................................... 15 1.5.7 Rx Modem Filter and Equaliser .............................................. 16 1.5.8 FSK Demodulator..................................................................... 16 1.5.9 Rx Data Register and USART ................................................. 16 1.5.10 Rx Modem Pattern Detectors.................................................. 18 1.5.11 Analogue Signal Routing ........................................................ 18 1.5.12 'C-BUS' Interface ...................................................................... 19 1.5.12.1 General Reset Command ............................... 19 1.5.12.2 General Control Register ............................... 21 1.5.12.3 Transmit Mode Register ................................. 23 1.5.12.4 Receive Mode Register................................... 26 1.5.12.5 Tx Data Register.............................................. 28 1.5.12.6 Rx Data Register ............................................. 28 1.5.12.7 Analogue Signal Path Register ..................... 29 1.5.12.8 Status Register................................................ 30 1.5.12.9 Programming Register ................................... 33 1.5.12.10 Other Registers ............................................... 35 1.6 Application Notes ................................................................................. 36 1.7 Performance Specification................................................................... 37 1.7.1 Electrical Performance ............................................................ 37 1.7.1.1 Absolute Maximum Ratings....................................... 37 1.7.1.2 Operating Limits ......................................................... 37 1.7.1.3 Operating Characteristics.......................................... 38 It is always recommended that you check for the latest product datasheet version from the Datasheets page of the CML website: [www.cmlmicro.com]. © 2008 CML Microsystems Plc 4 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.2 CMX860 Block Diagram Figure 1 Block Diagram © 2008 CML Microsystems Plc 5 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.3 CMX860 Signal List CMX860 D6, D1, E1 Signal Description Pin No. Name Type 1 XTALN O/P The output of the on-chip Xtal oscillator inverter. 2 XTAL/CLOCK I/P 3 RDRVN O/P 4 DVSS Power The input to the oscillator inverter from the Xtal circuit or external clock source. Relay drive output, low resistance pull down to DVSS when active and medium resistance pull up to DVDD when inactive. The digital negative supply rail (ground). 5 RD I/P 6 RT BI 7 RESETN I/P Schmitt trigger input to the Ring signal detector. Connect to DVSS if Ring Detector not used. Open drain output and Schmitt trigger input forming part of the Ring signal detector. Connect to DVDD if Ring Detector not used. An active-low reset pin. 8 LINERXF O/P The output of the Line Rx Input Amplifier. 9 LINERXN I/P The inverting input to the Line Rx Input Amplifier. 10 LINERXP I/P 11 PHONERXF O/P The non-inverting input to the Line Rx Input Amplifier. The output of the Phone Rx Input Amplifier. 12 PHONERXN I/P 13 PHONERXP I/P 14 AVSS Power 15 VBIAS O/P 16 PHONETXN O/P 17 PHONETXP O/P 18 LINETXN O/P 19 LINETXP O/P 20 AVDD Power 21 HT BI © 2008 CML Microsystems Plc The inverting input to the Phone Rx Input Amplifier. The non-inverting input to the Phone Rx Input Amplifier. The analogue negative supply rail (ground). Internally generated bias voltage of approximately AVDD /2, except when the device is in ‘Powersave’ mode when VBIAS will discharge to AVSS. Should be decoupled to AVSS by a capacitor mounted close to the device pins. The inverted output of the Phone Tx Output Driver. The non-inverted output of the Phone Tx Output Driver. The inverted output of the Line Tx Output Driver. The non-inverted output of the Line Tx Output Driver. The analogue positive supply rail. Levels and thresholds within the device are proportional to this voltage. Open drain output and Schmitt trigger input forming part of the Hook signal detector. Connect to DVDD if Hook Detector not used. 6 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 D6, D1, E1 CMX860 Signal Description Pin No. Name Type 22 HD I/P 23 CSN I/P Schmitt trigger input to the Hook signal detector. Connect to DVSS if Hook Detector not used. The 'C-BUS' chip select input from the μC. 24 COMMAND DATA I/P The 'C-BUS' serial data input from the μC. 25 SERIAL CLOCK I/P The 'C-BUS' serial clock input from the μC. 26 REPLY DATA T/S 27 IRQN O/P 28 DVDD Power A 3-state 'C-BUS' serial data output to the μC. This output is high impedance when not sending data to the μC. A ‘wire-ORable’ output for connection to a μC Interrupt Request input. This output is pulled down to DVSS when active and is high impedance when inactive. An external pullup resistor is required i.e. R1 of Figure 2. The digital positive supply rail. Levels and thresholds within the device are proportional to this voltage. I/P = Input O/P = Output BI = Bidirectional T/S = 3-state Output NC = No Connection © 2008 CML Microsystems Plc 7 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.4 CMX860 External Components C1, C2 R1 X1 22pF 100kΩ 11.0592MHz or 12.288MHz C3, C4, C6 C5, C7 L1, L2 100nF 10uF 100nH (optional) Resistors ±5%, capacitors and inductors ±20% unless otherwise stated. Figure 2a Recommended External Components for a Typical Application This device is capable of detecting and decoding small amplitude signals. To achieve this DVDD, AVDD and VBIAS should be decoupled and the receive path protected from extraneous in-band signals. It is recommended that the printed circuit board is laid out with both AVSS and DVSS ground planes in the CMX860 area, as shown in Figure 2b, with provision to make a link between them close to the CMX860. To provide a low impedance connection to ground, the decoupling capacitors (C3 – C7) must be mounted as close to the CMX860 as possible and connected directly to their respective ground plane. This will be achieved more easily by using surface mounted capacitors. VBIAS is used as an internal reference for detecting and generating the various analogue signals. It must be carefully decoupled, to ensure its integrity. Apart from the decoupling capacitor shown (C3), no other loads are allowed. If VBIAS needs to be used to set external analogue levels, it must be buffered with a high input impedance buffer. The DVSS connections to the Xtal oscillator capacitors C1 and C2 should also be of low impedance and preferably be part of the DVSS ground plane to ensure reliable start up of the oscillator. © 2008 CML Microsystems Plc 8 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Figure 2b Recommended Power Supply Connections and De-coupling ANALOGUE C3, C6 C7 L2 Note: DIGITAL 100nF 10uF 100nH (optional, see note) C4 C5 L1 100nF 10uF 100nH (optional, see note) The inductors L1 and L2 can be omitted but this may degrade system performance. © 2008 CML Microsystems Plc 9 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.4.1 CMX860 Ring Detector Interface Figure 3 shows how the CMX860 may be used to detect the large amplitude ringing signal voltage present on the 2-wire line at the start of an incoming telephone call. The ring signal is usually applied at the subscriber's exchange as an ac voltage inserted in series with one of the telephone wires and will pass through either C20 and R20 or C21 and R21 to appear at the top end of R22 (point X in Figure 3) in a rectified and attenuated form. The signal at point X is further attenuated by the potential divider formed by R22 and R23 before being applied to the CMX860 RD input. If the amplitude of the signal appearing at RD is greater than the input threshold (Vthi) of Schmitt trigger 'A' then the N transistor connected to RT will be turned on, pulling the voltage at RT to DVSS by discharging the external capacitor C22. The output of the Schmitt trigger 'B' will then go high, setting bit 14 (Ring Detect) of the Status Register. The minimum amplitude ringing signal that is certain to be detected is: ( 0.7 + Vthi x [R20 + R22 + R23] / R23 ) x 0.707 Vrms where Vthi is the high-going threshold voltage of the Schmitt trigger A (see section 1.7.1). With R20 - R22 all 470kΩ as Figure 3, then setting R23 to 68kΩ will guarantee detection of ringing signals of 40Vrms and above for DVDD over the range 3V to 5V. R20, 21, 22 R23 R24 C20, 21 C22 D1-4 470kΩ See text 470kΩ 0.1μF 0.33μF 1N4004 Resistors ±5%, capacitors ±20% Figure 3 Ring Signal Detector Interface Circuit © 2008 CML Microsystems Plc 10 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 If the time constant of R24 and C22 is large enough then the voltage on RT will remain below the threshold of the 'B' Schmitt trigger for the duration of a ring cycle. The time for the voltage on RT to charge from DVSS towards DVDD can be derived from the formula: VRT = DVDD x [1 - exp(-t/(R24 x C22)) ] As the Schmitt trigger high-going input threshold voltage (Vthi) has a minimum value of 0.56 x DVDD, then the Schmitt trigger B output will remain high for a time of at least 0.821 x R24 x C22 following a pulse at RD. The values of R24 and C22 given in Figure 3 (470kΩ and 0.33μF) give a minimum RT charge time of 100 msec, which is adequate for ring frequencies of 10Hz or above. Note that the circuit will also respond to a telephone line voltage reversal. If necessary the μC can distinguish between a Ring signal and a line voltage reversal by measuring the time that bit 14 of the Status Register (Ring Detect) is high. If the Ring detect function is not used then pin RD should be connected to DVSS and RT to DVDD. 1.4.2 Hook Detector Interface This is identical internally to the Ring Detector interface circuit and similar components could be used externally, with appropriate values, if hook detection is to be performed by detecting a voltage change across the tip and ring lines to the local phone. 1.4.3 RESETN pin When this pin is taken low, it performs the same operation as a C-BUS General Reset command. As a consequence the device will enter the powersaved state. Refer to section 1.5.12.1 (General Reset Command) and 1.5.12.2 (General Control Register, Powerup bit) for further information. © 2008 CML Microsystems Plc 11 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5 CMX860 General Description The CMX860 transmit and receive operating modes are independently programmable. The transmit mode can be set to any one of the following: V.23 modem. 1200 or 75 bps FSK. Bell 202 modem. 1200 or 150 bps FSK. DTMF transmit. Single tone transmit (from a range of modem calling, answer and other tone frequencies) User programmed tone or tone pair transmit (programmable frequencies and levels) Disabled. The receive mode can be set to any one of the following: V.23 modem. 1200 or 75 bps FSK. Bell 202 modem. 1200 or 150 bps FSK. DTMF decode. 2100Hz and 2225Hz answer tone detect. Call progress signal detect. User programmed tone or tone pair detect. Disabled. The CMX860 may also be set into a Powersave mode which disables all circuitry except for the 'C-BUS' interface, the Ring Detector and the Hook Detector. © 2008 CML Microsystems Plc 12 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.1 CMX860 Tx USART A flexible Tx USART is provided. It can be programmed to transmit continuous patterns, Start-Stop characters or Synchronous Data. In both Synchronous Data and Start-stop modes the data to be transmitted is written by the µC into the 8bit 'C-BUS' Tx Data Register from which it is transferred to the Tx Data Buffer. If Synchronous Data mode has been selected the 8 data bits in the Tx Data Buffer are transmitted serially, b0 being sent first. In Start-stop mode a single Start bit is transmitted, followed by 5, 6, 7 or 8 data bits from the Tx Data Buffer - b0 first - followed by an optional Parity bit then - normally - one or two Stop bits. The Start, Parity and Stop bits are generated by the USART as determined by the Tx Mode Register settings and are not taken from the Tx Data Register. Figure 4a Tx USART Every time the contents of the 'C-BUS' Tx Data Register are transferred to the Tx Data Buffer the Tx Data Ready flag bit of the Status Register is set to 1 to indicate that a new value should be loaded into the 'CBUS' Tx Data Register. This flag bit is cleared to 0 when a new value is loaded into the Tx Data Register. Figure 4b Tx USART Function (Start-Stop mode, 8 Data Bits + Parity) If a new value is not loaded into the Tx Data Register in time for the next Tx Data Register to Tx Data Buffer transfer then the Status Register Tx Data Underflow bit will be set to 1. In this event the contents of the Tx Data Buffer will be re-transmitted if Synchronous Data mode has been selected, or if the Tx modem is in Start-stop mode then a continuous Stop signal (1) will be transmitted until a new value is loaded into the Tx Data Register. The transmitted bit rates are determined by the XTAL frequency. © 2008 CML Microsystems Plc 13 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.2 CMX860 FSK Modulator Serial data from the USART is fed to the FSK modulator. One of two frequencies is generated according to the current transmit data bit. 1.5.3 Tx Filter and Equaliser The FSK modulator output signal is fed through the Transmit Filter and Equaliser block which limits the out-of-band signal energy to acceptable limits. When transmitting 1200bps FSK, this block includes a fixed compromise line equaliser which may be enabled or disabled by bit 10 of the General Control Register. The amount of Tx equalisation provided compensates for one quarter of the relative amplitude and delay distortion of ETS Test Line 1 over the frequency band used. 1.5.4 DTMF/Tones Generator In DTMF/Tones mode this block generates DTMF signals or single or dual frequency tones. 1.5.5 Tx Level Control and Output Drivers The CMX860 generated signal (if present) from the FSK/DTMF/Tones Generator is passed through the programmable Tx Level Control before being passed to the switched paths controlled by the Analogue Signal Path Register. The Tx Output Drivers have symmetrical outputs to provide sufficient line voltage swing at low values of AVDD and to reduce harmonic distortion of the signal. The Drivers can also transmit the signal from the other port (e.g. Phone Input to Line Driver) or can be independently set to Bias or Powersaved – see Analogue Signal Path Register. © 2008 CML Microsystems Plc 14 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.6 CMX860 DTMF Decoder and Tone Detectors In Rx Tones Detect mode the received signal, after passing through the Rx Gain Control block, is fed to the DTMF decoder and Dual Tone/Call Progress/Answer Tone detector. The user may select one of four separate operations: The DTMF decoder detects standard DTMF signals. A valid DTMF signal will set bit 5 of the Status Register to 1 for as long as the signal is detected. The DTMF signal is then decoded and output in bits 0 to 3 of the Status Register. The programmable tone pair detector includes two separate tone detectors (see Figure 9a). The first detector will set bit 6 of the Status Register for as long as a valid signal is detected, the second detector sets bit 7, and bit 10 of the Status Register will be set when both tones are detected. The frequency and bandwidth of each detector can be set in the Programming Register. Without programming, the default values in the Programming Register are set for 2130 and 2750 Hz detection. The Call Progress detector measures the amplitude of the signal at the output of a 275 Hz - 665 Hz bandpass filter and sets bit 10 of the Status Register to 1 when the signal level exceeds the measurement threshold. 10 0 -10 -20 dB -30 -40 -50 -60 0 0.5 1 1.5 2 kHz 2.5 3 3.5 4 Figure 5a Response of the Call Progress Filter The Answer Tone detector measures both amplitude and frequency of the received signal and sets bit 6 or bit 7 respectively of the Status Register when a valid 2225Hz or 2100Hz signal is received. © 2008 CML Microsystems Plc 15 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.7 CMX860 Rx Modem Filter and Equaliser When the receive part of the CMX860 is operating as a modem, the received signal is fed to a bandpass filter to attenuate unwanted signals and to provide fixed compromise line equalisation. The line equaliser may be enabled or disabled by bit 10 of the General Control Register and compensates for one quarter of the relative amplitude and delay distortion of ETS Test Line 1. A typical response of this filter, including the line equaliser, is shown in Figure 5b. The effect of external components should also be considered in determining the overall response: 10 0 -10 -20 dB -30 -40 -50 -60 0 0.5 1 1.5 2 2.5 3 3.5 4 kHz Figure 5b V.23 / Bell 202 Rx Filters The signal level at the output of the Receive Modem Filter and Equaliser is measured in the Modem Energy Detector block, compared to a threshold value, and the result controls bit 10 of the Status Register. The output of the Receive Modem Filter and Equaliser is also fed to the FSK demodulator. 1.5.8 FSK Demodulator The FSK demodulator recognises individual frequencies as representing received ‘1’ or ‘0’ data bits: The FSK demodulator produces a serial data bit stream which is fed to the Rx USART block, see Figure 6a. This bit stream is also monitored for continuous ‘1010’s and for continuous 1’s. The outputs of these pattern detectors control bits 9 and 7 respectively of the Status Register. 1.5.9 Rx Data Register and USART The Rx USART can be programmed to treat the received data bit stream as Synchronous data or as Start-Stop characters. In Synchronous mode the received data bits are all fed into the Rx Data Buffer which is copied into the 'C-BUS' Rx Data Register after every 8 bits. In Start-stop mode the USART Control logic looks for the start of each character, then feeds only the required number of data bits (not parity) into the Rx Data Buffer. The parity bit (if used) and the presence © 2008 CML Microsystems Plc 16 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 of a Stop bit are then checked and the data bits in the Rx Data Buffer copied to the 'C-BUS' Rx Data Register. Figure 6a Rx Modem Data Paths Whenever a new character is copied into the 'C-BUS' Rx Data Register, the Rx Data Ready flag bit of the Status Register is set to 1 to prompt the µC to read the new data, and, in Start-stop mode, the Even Rx Parity flag bit of the Status Register is updated. In Start-stop mode, if the Stop bit is missing (received as a ‘0’ instead of a ‘1’) the received character will still be placed into the Rx Data Register and the Rx Data Ready flag bit set, but the Status Register Rx Framing Error bit will also be set to ‘1’ and the USART will re-synchronise onto the next ‘1’ – ‘0’ (Stop – Start) transition. The Rx Framing Error bit will remain set until the next character has been received. Figure 6b Rx USART Function (Start-stop mode, 8 Data Bits + Parity) If the µC has not read the previous data from the Rx Data Register by the time that new data is copied to it from the Rx Data Buffer then the Rx Data Overflow flag bit of the Status Register will be set to 1. The Rx Data Ready flag and Rx Data Overflow bits are cleared to 0 when the Rx Data Register is read by the µC. © 2008 CML Microsystems Plc 17 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 1.5.10 Rx Modem Pattern Detectors The '1010' pattern detector will set bit 9 of the Status Register when 32 bits of alternating 1's and 0's have been received. The continuous 1's detector will set bit 7 of the Status Register when 32 consecutive 1's have been received. Both pattern detectors will hold their 'detect' output for 12 bit times after the end of the detected pattern unless the received bit rate or operating mode is changed, in which case the detectors are reset within 2ms. 1.5.11 Analogue Signal Routing The routing of signals to and from the Line and Phone interfaces is performed by bits 0 to 4 of the Analogue Signal Path Register. Please note that bits 5 to 7 of this register are reserved for future use and should be set to zero. © 2008 CML Microsystems Plc 18 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 1.5.12 'C-BUS' Interface This block provides for the transfer of data and control or status information between the CMX860’s internal registers and the µC over the 'C-BUS' serial bus. Each transaction consists of a single Register Address byte sent from the µC which may be followed by one or more data byte(s) sent from the µC to be written into one of the CMX860’s Write Only Registers, or one or more byte(s) of data read out from one of the CMX860’s Read Only Registers, as illustrated in Figure 7. Data sent from the µC on the Command Data line is clocked into the CMX860 on the rising edge of the Serial Clock input. Reply Data sent from the CMX860 to the µC is valid when the Serial Clock is high. The CSN line must be held low during a data transfer and kept high between transfers. The 'C-BUS' interface is compatible with most common µC serial interfaces and may also be easily implemented with general purpose µC I/O pins controlled by a simple software routine. Figure 13 gives detailed 'C-BUS' timing requirements. The following 'C-BUS' addresses and registers are used by the CMX860: General Reset Command (address only, no data). General Control Register, 16-bit write only. Transmit Mode Register, 16-bit write-only. Receive Mode Register, 16-bit write-only. Transmit Data Register, 8-bit write only. Receive Data Register, 8-bit read-only. Status Register, 16-bit read-only. Programming Register, 16-bit write-only. Analogue Signal Path Register, 8-bit write-only. Address $01 Address $E0 Address $E1 Address $E2 Address $E3 Address $E5 Address $E6 Address $E8 Address $EC Notes: 1. The 'C-BUS' addresses $E9, $EA and $EB are allocated for production testing and should not be accessed in normal operation. 2. The 'C-BUS' address $E4 is allocated for internal use and should not be accessed in normal operation. 3. In several registers there are bit patterns whose function is not specified. These modes should not be accessed in normal operation and no guarantee is given that any use of these bits will be supported in the future. 1.5.12.1 General Reset Command General Reset Command (no data) 'C-BUS' address $01 This command resets the device and clears all bits of the General Control, Analogue Signal Path, Programming, Transmit Mode and Receive Mode Registers and all bits of the Status Register except b14 and b8. The clearing of the General Control Register will put the device into Powersave. See the description of General Control Register b8 for the procedure on how to power-up the device. Whenever power is applied to the CMX860, a General Reset command should be sent to the device or the RESETN pin should be pulsed low. Either action will cause the device to enter a powersave state (General Control Register bit 8 will be cleared to '0'). Note that the CMX860 does not automatically perform a power-on reset when power is first applied. To bring the device out of powersave, please refer to the description of bits 7 and 8 in the General Control Register, section 1.5.12.2. © 2008 CML Microsystems Plc 19 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Figure 7 'C-BUS' Transactions © 2008 CML Microsystems Plc 20 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.2 CMX860 General Control Register General Control Register: 16-bit write-only. 'C-BUS' address $E0 This register controls general features of the CMX860 such as the Powersave mode, the IRQ mask bits and the Relay Drive output. It also allows the fixed compromise equalisers in the Tx and Rx signal paths to be disabled if desired, and sets the internal clock dividers to use either a 11.0592 or a 12.288 MHz XTAL frequency. All bits of this register are cleared to 0 by a General Reset command. Bit: 15 14 13 12 11 10 9 8 7 6 0 0 0 Xtal freq Hook IRQ Mask Equ Rly drv Pwr Rst Irqn en 5 4 3 2 1 0 IRQ Mask Bits General Control Register b15-13: Reserved, set to 000 General Control Register b12: Xtal frequency This bit should be set according to the Xtal frequency. b12 = 1 b12 = 0 11.0592MHz 12.2880MHz General Control Register b11: Hook Detect IRQ Mask bit This bit affects the operation of the IRQ bit of the Status Register as described in section 1.5.12.8 General Control Register b10: Tx and Rx Fixed Compromise Equaliser This bit allows the Tx and Rx fixed compromise equaliser in the modem transmit and receive filter blocks to be disabled. b10 = 1 b10 = 0 Disable equaliser Enable equaliser (1200bps modem mode) General Control Register b9: Relay Drive This bit directly controls the RDRVN output pin. b9 = 1 b9 = 0 © 2008 CML Microsystems Plc RDRVN output pin pulled to DVSS RDRVN output pin pulled to DVDD 21 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 General Control Register b8: Powerup This bit controls the internal power supply to most of the internal circuits, including the Xtal oscillator and VBIAS supply. Note that the General Reset command clears this bit, putting the device into Powersave mode. b8 = 1 b8 = 0 Device powered up normally Powersave mode (all circuits except Ring Detect, Hook Detect, RDRVN and 'C-BUS' interface disabled) When power is first applied to the device, the following powerup procedure should be followed to ensure correct operation. i. ii. iii. iv. (Power is applied to the device) Issue a General Reset command or momentarily set the RESETN pin low. Write to the General Control Register (address $E0) setting both the Powerup bit (b8) and the Reset bit (b7) to 1 – leave in this state for a minimum of about 20ms – it is required that the crystal initially runs for this time in order to clock the internal logic into a defined state. The device is now powered up, with the crystal and VBIAS supply operating, but is otherwise not running any transmit or receive functions. The device is now ready to be programmed as and when required. Examples: • A General Reset command could be issued to clear all the registers and therefore powersave the device. • The Reset bit in the General Control Register could be set to 0 as part of a routine to program all the relevant registers for setting up a particular operating mode. When the device is switched from Powersave mode to normal operation by setting the Powerup bit to 1, the Reset bit should also be set to 1 and should be held at 1 for about 20ms while the internal circuits, Xtal oscillator and VBIAS stabilise before starting to use the transmitter or receiver. General Control Register b7: Reset Setting this bit to 1 resets the CMX860’s internal circuitry, clearing all bits of the Analogue Signal Path, Programming, Transmit and Receive Mode Registers and b13-0 of the Status Register. b7 = 1 b7 = 0 Internal circuitry in a reset condition. Normal operation General Control Register b6: IRQNEN (IRQN O/P Enable) Setting this bit to 1 enables the IRQN output pin. b6 = 1 b6 = 0 IRQN pin driven low (to DVSS) if the IRQ bit of the Status Register = 1 IRQN pin disabled (high impedance) General Control Register b5-0: IRQ Mask bits These bits affect the operation of the IRQ bit of the Status Register as described in section 1.5.12.8 © 2008 CML Microsystems Plc 22 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.3 CMX860 Transmit Mode Register Transmit Mode Register: 16-bit write-only. 'C-BUS' address $E1 This register controls the CMX860 transmit signal type and level. All bits of this register are cleared to 0 by a General Reset command, or when b7 (Reset) of the General Control Register is 1. Bit: 15 14 13 12 11 10 9 8 7 6 5 Tx mode = modem Tx level set to 00 set to 00 Tx mode = DTMF/Tones Tx mode = Disabled Tx level Unused, set to 0000 Set to 0000 0000 0000 4 3 2 1 0 Start-stop / # data bits / synch data synch data source DTMF or Tone select Tx Mode Register b15-12: Tx mode These 4 bits select the transmit operating mode. b15 b14 b13 b12 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 1 0 1 0 1 0 V.23 FSK V.23 FSK Bell 202 FSK Bell 202 FSK DTMF / Tones Transmitter disabled 1200 bps 75 bps 1200 bps 150 bps Tx Mode Register b11-9: Tx level These 3 bits set the gain of the Tx Level Control block. b11 b10 b9 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 © 2008 CML Microsystems Plc 0dB -1.5dB -3.0dB -4.5dB -6.0dB -7.5dB -9.0dB -10.5dB 23 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Tx Mode Register b8-5: Reserved, set to 0000 Tx Mode Register b4-3: Tx Data Format (both FSK modes) These two bits select Synchronous or Start-stop mode and the addition of a parity bit to transmitted characters in Start-stop mode. b4 1 1 0 0 b3 1 0 1 0 Synchronous mode Start-stop mode, no parity Start-stop mode, even parity bit added to data bits Start-stop mode, odd parity bit added to data bits Tx Mode Register b2-0: Tx Data and Stop bits (FSK Start-stop mode) In Start-stop mode these three bits select the number of Tx data and stop bits. b2 1 1 1 1 0 0 0 0 b1 1 1 0 0 1 1 0 0 b0 1 0 1 0 1 0 1 0 8 data bits, 2 stop bits 8 data bits, 1 stop bit 7 data bits, 2 stop bits 7 data bits, 1 stop bit 6 data bits, 2 stop bits 6 data bits, 1 stop bit 5 data bits, 2 stop bits 5 data bits, 1 stop bit Tx Mode Register b2-0: Tx Data source (FSK Synchronous mode) In Synchronous mode (b4-3 = 11) these three bits select the source of the data fed to the Tx FSK modulator. b2 1 0 0 0 b1 x 1 1 0 © 2008 CML Microsystems Plc b0 x 1 0 x Data bytes from Tx Data Buffer Continuous 1s Continuous 0s Continuous alternating 1s and 0s 24 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Tx Mode Register b8-0: DTMF/Tones mode If DTMF/Tones transmit mode has been selected (Tx Mode Register b15-12 = 0001) then b8-5 should be set to 0000 and b4-0 will select a DTMF signal or a fixed tone or one of four programmed tones or tone pairs for transmission. b4 = 0: Tx fixed tone or programmed tone pair b3 b2 b1 b0 Tone frequency (Hz) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 No tone 697 770 852 941 1209 1336 1477 1633 1300 2100 2225 Tone pair TA Tone pair TB Tone pair TC 2130 and 2750 Hz by default (Calling tone) (Answer tone) (Answer tone) Programmed Tx tone / tone pair, see 1.5.12.9 “ “ Tx tone / tone pair TD when TD programmed b4 = 1: Tx DTMF b3 b2 b1 b0 Low frequency (Hz) High frequency (Hz) Keypad symbol 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 941 697 697 697 770 770 770 852 852 852 941 941 941 697 770 852 1633 1209 1336 1477 1209 1336 1477 1209 1336 1477 1336 1209 1477 1633 1633 1633 D 1 2 3 4 5 6 7 8 9 0 * # A B C © 2008 CML Microsystems Plc 25 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.4 CMX860 Receive Mode Register Receive Mode Register: 16-bit write-only. 'C-BUS' address $E2 This register controls the CMX860 receive signal type and level. All bits of this register are cleared to 0 by a General Reset command, or when b7 (Reset) of the General Control Register is 1. Bit: 15 14 13 12 11 10 Rx mode = modem Rx level Rx mode = Tones detect Rx mode = Disabled Rx level 9 8 7 6 Set to 00 5 4 3 2 1 0 Start-stop/Synch No. of bits and parity DTMF/Tones/Call Progress select Set to 0000 0000 0000 (bit 8 should be set to ‘0’) Rx Mode Register b15-12: Rx mode These 4 bits select the receive operating mode. b15 b14 b13 b12 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 0 0 1 0 1 0 1 0 V.23 FSK 1200 bps V.23 FSK 75 bps Bell 202 FSK 1200 bps Bell 202 FSK 150 bps DTMF, Programmed tone pair, Answer Tone, Call Progress detect Receiver disabled Rx Mode Register b11-9: Rx level These three bits set the gain of the Rx Gain Control block. b11 b10 b9 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 © 2008 CML Microsystems Plc 0dB -1.5dB -3.0dB -4.5dB -6.0dB -7.5dB -9.0dB -10.5dB 26 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Rx Mode Register b8-6: Reserved, set to 000 Rx Mode Register b5-3: Rx USART Setting (both FSK modes) These three bits select the Rx USART operating mode. b5 1 1 0 b4 1 1 x b3 1 0 x Rx Synchronous mode Rx Start-stop mode Rx USART function disabled Rx Mode Register b2-0: Rx Data bits and parity (FSK Start-stop mode) In Start-stop mode these three bits select the number of data bits (plus any parity bit) in each received character. b2 1 1 1 1 0 0 0 0 b1 1 1 0 0 1 1 0 0 b0 1 0 1 0 1 0 1 0 8 data bits + parity 8 data bits 7 data bits + parity 7 data bits 6 data bits + parity 6 data bits 5 data bits + parity 5 data bits Rx Mode Register b2-0: Rx Data bits and parity (FSK Synchronous mode) These bits are ignored in Synchronous mode. Rx Mode Register b2-0: Tones Detect mode In Tones Detect Mode (Rx Mode Register b15-12 = 0001) b8-3 should be set to 000000 Bits 2-0 select the detector type. b2 b1 b0 1 0 0 Programmable Tone Pair Detect 0 1 1 Call Progress Detect 0 1 0 2100, 2225Hz Answer Tone Detect 0 0 1 DTMF Decode 0 0 0 Disabled © 2008 CML Microsystems Plc 27 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.5 Tx Data Register Tx Data Register: 8-bit write-only. Bit: CMX860 7 6 5 4 3 'C-BUS' address $E3 2 1 0 Data bits to be transmitted In Synchronous Tx data mode this register contains the next 8 data bits to be transmitted. Bit 0 is transmitted first. In Tx Start-stop mode the specified number of data bits will be transmitted from this register (b0 first). A Start bit, a Parity bit (if required) and Stop bit(s) will be added automatically. This register should only be written to when the Tx Data Ready bit of the Status Register is 1. 1.5.12.6 Rx Data Register Rx Data Register: 8-bit read-only. Bit: 7 6 5 4 3 'C-BUS' address $E5 2 1 0 Received data bits In unformatted Rx data mode this register contains 8 received data bits, b0 of the register holding the earliest received bit, b7 the latest. In Rx Start-stop data mode this register contains the specified number of data bits from a received character, b0 holding the first received bit. © 2008 CML Microsystems Plc 28 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.7 CMX860 Analogue Signal Path Register Analogue Signal Path Register: 8-bit write-only. 'C-BUS' address $EC This register controls the routing of the analogue signal paths and controls the output drivers. Bit: 7 6 5 0 0 0 4 3 2 Line Driver Mode 1 Phone Driver Mode 0 Input Selector Control Bits 7-5 of the Analogue Signal Path Register are reserved for future use and should be set to 0. Analogue Signal Path Register b4-3: Line Driver Mode These bits control the complementary Line Driver and select the signal to be transmitted. b4 0 0 1 1 b3 0 1 0 1 Line Driver Mode Off / High Impedance Transmit Phone-derived Signal Transmit CMX860 Generated Signal Transmit Bias Level Analogue Signal Path Register b2-1: Phone Driver Mode These bits control the complementary Phone Driver and select the signal to be transmitted. b2 0 0 1 1 b1 0 1 0 1 Phone Driver Mode Off / High Impedance Transmit Line-derived Signal Transmit CMX860 Generated Signal Transmit Bias Level Analogue Signal Path Register b0: Input Selector Control This bit selects between the Line and Phone as inputs to the CMX860’s decoders/detectors. Note: both op-amps remain powered up even when not selected (unless device is powersaved). b0 = 1 b0 = 0 Line-derived signal to decoders/detectors Phone-derived signal to decoders/detectors Notes: 1. ‘Line-derived signal’ means the signal at the output of the Line input op-amp. ‘Phonederived signal’ means the signal at the output of the Phone input op-amp. The ‘CMX860 Generated Signal’ means the signal from the DTMF/Tones or FSK generators. 2. When the device is put into Powersave by setting Bit 8 of the General Control Register to 1, the transmit drivers and receive op-amps are powersaved and their outputs go high impedance. The settings of the Analogue Signal Path Register are unaffected, however. © 2008 CML Microsystems Plc 29 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.8 CMX860 Status Register Status Register: 16-bit read-only. 'C-BUS' address $E6 Bits 13-9 and 7-0 of this register are cleared to 0 by a General Reset command, or when b7 (Reset) of the General Control Register is 1. Bit: 15 14 13 IRQ RD PF 12 11 10 9 8 7 6 5 4 3 2 1 0 See below for uses of these bits The meanings of the Status Register bits 12-9 and 7-0 depend on whether the receive circuitry is in Modem or Tones Detect mode. Status Register bits: Rx Modem modes b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Note: Rx Tones Detect modes ** IRQ Mask bit IRQ Set to 1 on Ring Detect Programming Flag bit. See 1.5.12.9 Set to 1 on Tx data ready. Cleared by write to Tx Data Register Set to 1 on Tx data underflow. Cleared by write to Tx Data Register 1 when energy is detected in Rx 1 when energy is detected in Call modem signal band Progress band or when both programmable tones are detected 1 when ‘1010..’ pattern is detected 0 in FSK modes Set to 1 on Hook Detect 1 when continuous 1’s pattern 1 when 2100Hz answer tone or the detected in FSK modes second programmable tone is detected Set to 1 on Rx data ready. 1 when 2225Hz answer tone or the Cleared by read from Rx Data first programmable tone is detected Register Set to 1 on Rx data overflow. 1 when DTMF code is detected Cleared by read from Rx Data Register Set to 1 on Rx framing error 0 Set to 1 on even Rx parity Rx DTMF code b3, see table 0 Rx DTMF code b2 0 Rx DTMF code b1 FSK frequency demodulator output Rx DTMF code b0 b5 b4 b3 b3 b2 b1 b11 b1 b0 b0 - ** This column shows the corresponding IRQ Mask bits in the General Control Register. © 2008 CML Microsystems Plc 30 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Certain events of the Status Register bits 14-5 will cause the IRQ bit b15 to be set to 1 if the corresponding IRQ Mask bit is 1. These events are: for Status Register Bit 14 (Ring Detect), Bit 10 (Energy or Call Progress / Programmable Tones Detect) and Bit 8 (Hook Detect), both positive-going (0 to 1) and negative-going (1 to 0) transitions, for the remaining Status Register bits, only positive-going (0 to 1) transitions. The IRQ bit is cleared by a read of the Status Register or a General Reset command or by setting b7 or b8 of the General Control Register to 1. The operation of the data demodulator and pattern detector circuits within the CMX860 does not depend on the state of the Rx energy detect function. Rx Signal or Hook/Ring Detect Hold time Status Register bit 5,6,7,8,9 or 10 Detect time Note 3 Status Register bit 15 (IRQ) Note 1 IRQN output Note 2 Note 4 Notes: 1. IRQ will go high only if appropriate IRQ Mask bit in General Control Register is set. The IRQ bit is cleared by a read of the Status Register. 2. IRQN o/p will go low when IRQ bit high if IRQNEN bit of General Control Register is set. 3. In Rx Modem modes Status Register bits 5 and 6 are set by a Rx Data Ready or Rx Data Underflow event and cleared by a read of the Rx Data Register. 4. Status Bits 14,10 and 8 will also set the IRQ bit to 1 on a negative-going transition. Figure 8a Operation of Status Register bits 5-10 The IRQN output pin will be pulled low (to DVSS) when the IRQ bit of the Status Register and the IRQNEN bit (b6) of the General Control Register are both 1. Changes to Status Register bits caused by a change of Tx or Rx operating mode can take up to 150μs to take effect. In Powersave mode or when the Reset bit (b7) of the General Control Register is 1, the Ring Detect bit (b14) and the Hook Detect bit (b8) continue to operate. © 2008 CML Microsystems Plc 31 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Rx Modem Mode: In Rx Modem mode b0 will show the output of the frequency demodulator, updated at 8 times the nominal data rate. Rx Tones Detect Mode: Figure 8b Operation of Status Register for DTMF Rx b3 b2 b1 b0 Low frequency (Hz) High frequency (Hz) Keypad symbol 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 941 697 697 697 770 770 770 852 852 852 941 941 941 697 770 852 1633 1209 1336 1477 1209 1336 1477 1209 1336 1477 1336 1209 1477 1633 1633 1633 D 1 2 3 4 5 6 7 8 9 0 * # A B C Received DTMF Code: b3-0 of Status Register © 2008 CML Microsystems Plc 32 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.5.12.9 CMX860 Programming Register (includes generation & detection of 2130 and 2750 Hz) Programming Register : 16-bit write-only. 'C-BUS' address $E8 This register is used to program the transmit and receive programmed tone pairs by writing appropriate values to RAM locations within the CMX860. Note that these RAM locations are cleared by Powersave or Reset. The Programming Register should only be written to when the Programming Flag bit (b13) of the Status Register is 1. The act of writing to the Programming Register clears the Programming Flag bit. When the programming action has been completed (normally within 150μs) the CMX860 will set the bit back to 1. When programming Transmit or Receive Tone Pairs, do not change the Transmit or Receive Mode Registers until programming is complete and the Programming Flag bit has returned to 1. Transmit Tone Pair Programming 4 transmit tone pairs (TA to TD) can be programmed. The frequency (max 3.4kHz) and level must be entered for each tone to be used. Single tones are programmed by setting both level and frequency values to zero for one of the pair. Programming is done by writing a sequence of up to seventeen 16-bit words to the Programming Register. The first word should be 32768 (8000 hex), the following 16-bit words set the frequencies and levels and are in the range 0 to 16383 (0-3FFF hex). Each word is written as a 2 x data-byte CBUS transfer, see Figure 7c. Word 1 2 3 4 5 6 7 ----14 15 16 17 Tone Pair Value written 32768 Tone 1 frequency Tone 1 level Tone 2 frequency Tone 2 level Tone 1 frequency Tone 1 level ------------------Tone 1 frequency Tone 1 level Tone 2 frequency Tone 2 level TA TA TA TA TB TB ----TD TD TD TD Default Setting 2130 Hz -20 dBm 2750 Hz -20 dBm NB. Tone Pair TD is configured as 2130 and 2750 Hz by default, but can be re-programmed if required. The Frequency values to be entered are calculated from the formula: Value to be entered = desired frequency (Hz) * 3.414 i.e. for 1kHz the value to be entered is 3414 (or 0D56 in Hex). The Level values to be entered are calculated from the formula: Value to be entered = desired Vrms * 93780 / AVDD i.e. for 0.5Vrms at AVDD = 3.0V, the value to be entered is 15630 (3D0E in Hex) © 2008 CML Microsystems Plc 33 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Note that allowance should be made for the transmit signal filtering in the CMX860 which attenuates the output signal for frequencies above 2kHz by 0.25dB at 2.5kHz, by 1dB at 3kHz and by 2.2dB at 3.4kHz. Receive Tone Pair Programming The programmable tone pair detector is implemented as shown in Figure 9a. The filters are 4th order IIR sections. The frequency detectors measure the time taken for a programmable number of complete input signal cycles and compare this time against programmable upper and lower limits. NB. If this register is not programmed, the detector will be configured to operate in its default mode, which is for the detection of 2130 Hz ± 20 Hz and 2750 Hz ± 30 Hz. Figure 9a Programmable Tone Detectors Figure 9b Filter Implementation © 2008 CML Microsystems Plc 34 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Programming is done by writing a sequence of twenty-seven 16-bit words to the Programming Register. The first word should be 32769 (8001 hex), the following twenty-six 16-bit words set the frequencies and levels and are in the range 0 to 32767 (0000-7FFF hex). Each word is written as a 2 x data-byte CBUS transfer, see Figure 7c. Word 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Value written 32769 Filter #1 coefficient b21 Filter #1 coefficient b11 Filter #1 coefficient b01 Filter #1 coefficient a21 Filter #1 coefficient a11 Filter #1 coefficient b22 Filter #1 coefficient b12 Filter #1 coefficient b02 Filter #1 coefficient a22 Filter #1 coefficient a12 Freq measurement #1 ncycles Freq measurement #1 mintime Freq measurement #1 maxtime Word 15 16 17 18 19 20 21 22 23 24 25 26 27 Value written Filter #2 coefficient b21 Filter #2 coefficient b11 Filter #2 coefficient b01 Filter #2 coefficient a21 Filter #2 coefficient a11 Filter #2 coefficient b22 Filter #2 coefficient b12 Filter #2 coefficient b02 Filter #2 coefficient a22 Filter #2 coefficient a12 Freq measurement #2 ncycles Freq measurement #2 mintime Freq measurement #2 maxtime The coefficients are entered as 15-bit signed (two’s complement) integer values (the most significant bit of the 16-bit word entered should be zero) calculated as 8192 * coefficient value from the user’s filter design program (i.e. this allows for filter design values of -1.9999 to +1.9999). The design of the IIR filters should make allowance for the fixed receive signal filtering in the CMX860 which has a low pass characteristic above 1.5kHz of 0.4dB at 2kHz, 1.2dB at 2.5kHz, 2.6dB at 3kHz and 4.1dB at 3.4kHz. ‘ncycles’ is the number of signal cycles for the frequency measurement. ‘mintime’ is the smallest acceptable time for ncycles of the input signal expressed as the number of 9.6kHz timer clocks. i.e. ‘mintime’ = 9600 * ncycles / high frequency limit ‘maxtime’ is the highest acceptable time for ncycles of the input signal expressed as the number of 9.6kHz timer clocks. i.e. ‘maxtime’ = 9600 * ncycles / low frequency limit The level detectors include hysteresis. The threshold levels - measured at a 2-wire line interface with unity gain filters, using typical line interface circuits, 1.0 dB line coupling loss and with the Rx Gain Control block set to 0dB - are nominally: ‘Off’ to ‘On’ ‘On’ to ‘Off’ -44.5dBm -47.0dBm Note that if any changes are made to the programmed values while the CMX860 is running in Programmed Tone Detect mode they will not take effect until the CMX860 is next switched into Programmed Tone Detect mode. 1.5.12.10 Other Registers 'C-BUS' addresses $E4, $E9, $EA and $EB are reserved and should not be accessed. © 2008 CML Microsystems Plc 35 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.6 CMX860 Application Notes Figure 10 Typical Block Diagram for a Least Cost Router Application © 2008 CML Microsystems Plc 36 D/860/7 Telephone Signalling Transceiver / Least Cost Router 1.7 Performance Specification 1.7.1 Electrical Performance CMX860 1.7.1.1 Absolute Maximum Ratings Exceeding these maximum ratings can result in damage to the device. Supply (AVDD - AVSS) or (DVDD - DVSS) Voltage on any pin to AVSS or DVSS Voltage between AVSS and DVSS Voltage between AVDD and DVDD Current into or out of AVSS, DVSS, AVDD or DVDD pins Current into RDRVN pin (RDRVN pin low) Current into or out of any other pin Min. -0.3 -0.3 -50 -20 D6 Package Total Allowable Power Dissipation at Tamb = 25°C ... Derating Storage Temperature Operating Temperature Min. D1 Package Total Allowable Power Dissipation at Tamb = 25°C ... Derating Storage Temperature Operating Temperature Min. E1 Package Total Allowable Power Dissipation at Tamb = 25°C ... Derating Storage Temperature Operating Temperature Min. -55 -40 -55 -40 -55 -40 Max. 7.0 VDD + 0.3 ±50 ±300 +50 +50 +20 Units V V mV mV mA mA mA Max. 1490 14.9 +125 +85 Units mW mW/°C °C °C Max. 740 7.4 +125 +85 Units mW mW/°C °C °C Max. 1110 11.1 +125 +85 Units mW mW/°C °C °C Max. 5.5 +85 Units V °C 1.7.1.2 Operating Limits Correct operation of the device outside these limits is not implied. Notes Supply (AVDD - AVSS) or (DVDD - DVSS) Operating Temperature © 2008 CML Microsystems Plc 37 Min. 2.7 -40 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 1.7.1.3 Operating Characteristics For the following conditions unless otherwise specified: VDD = AVDD = DVDD = 2.7V to 5.5V at Tamb = -40 to +85°C, VSS = AVSS = DVSS Xtal Frequency = 11.0592 or 12.288MHz ± 0.01% (100ppm), 0dBm corresponds to 775mVrms. DC Parameters IDD (Powersave mode, VDD = 3.0V) (Reset but not powersave, VDD = 3.0V) (Reset but not powersave, VDD = 5.0V) (Running, VDD = 3.0V) (Running, VDD = 5.0V) Logic '1' Input Level Logic '0' Input Level Logic Input Leakage Current (Vin = 0 to DVDD), (excluding XTAL/CLOCK input) Output Logic '1' Level (lOH = 2 mA) Output Logic '0' Level (lOL = -3 mA) IRQN O/P 'Off' State Current (Vout = DVDD) Schmitt triggers input high-going threshold (Vthi) (see Figure 11) Schmitt triggers input low-going threshold (Vtlo) (see Figure 11) RDRVN ‘ON’ resistance to DVSS (DVDD= 3.0V) RDRVN ‘OFF’ resistance to DVDD (DVDD= 3.0V) Notes: Notes 1, 2 1, 3 1, 3 1 1 4 4 Min. 70% -1.0 Typ. 2.0 1.0 2.5 3.0 5.0 - 80% 0.56DVDD - 0.44DVDD - 0.6V - - Max. Units 2.0 4.5 5.0 9.0 30% +1.0 μA mA mA mA mA DVDD DVDD μA 0.4 1.0 0.56DVDD + 0.6V 0.44DVDD 50 1300 70 3000 DVDD V μA V V Ω Ω 1. At 25°C, not including any current drawn from the CMX860 pins by external circuitry other than X1, C1 and C2. 2. All logic inputs at DVSS except for RT and CSN inputs which are at DVDD. 3. General Mode Register b8 and b7 both set to 1. 4. Excluding RD, RT, HD and HT pins. 4 3.5 3 2.5 Vin 2 1.5 1 0.5 0 Vthi Vtlo 2.5 3 3.5 4 4.5 5 5.5 DVdd Figure 11 Typical Schmitt Trigger Input Voltage Thresholds vs. DVDD XTAL/CLOCK Input (timings for an external clock input) 'High' Pulse Width 'Low' Pulse Width © 2008 CML Microsystems Plc Notes 38 Min. Typ. Max. Units 30 30 - - ns ns D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Transmit V.23 FSK Mode Baud rate Mark (logical 1) frequency, 1200 baud Space (logical 0) frequency, 1200 baud Mark (logical 1) frequency, 75 baud Space (logical 0) frequency, 75 baud Notes 5 Min. 1298 2097 389 449 Typ. 1200/75 1300 2100 390 450 Max. 1302 2103 391 451 Units Baud Hz Hz Hz Hz Transmit Bell 202 FSK Mode Baud rate Mark (logical 1) frequency, 1200 baud Space (logical 0) frequency, 1200 baud Mark (logical 1) frequency, 150 baud Space (logical 0) frequency, 150 baud Notes 5 Min. 1198 2197 386 486 Typ. 1200/150 1200 2200 387 487 Max. 1202 2203 388 488 Units Baud Hz Hz Hz Hz DTMF/Single Tone Transmit Tone frequency accuracy Distortion Notes 6 Min. -0.2 - Typ. 1.0 Max. +0.2 2.0 Units % % Transmit Output Level Modem and Single Tone modes DTMF mode, Low Group tones DTMF: level of High Group tones wrt Low Group Tx output driver gain control accuracy Notes 6 6 6 6 Min. -4.0 -2.0 +1.0 -0.25 Notes: Typ. -3.0 -1.0 +2.0 - Max. -2.0 0.0 +3.0 +0.25 Units dBm dBm dB dB 5. Tx signal % baud or bit rate accuracy is the same as XTAL/CLOCK % frequency accuracy. 6. Measured between LINETXP and LINETXN or PHONETXP and PHONETXN pins with Tx Level Control gain set to 0dB, 1k2Ω load between the 'TXP and 'TXN pins, at AVDD = 3.0V (levels are proportional to AVDD). Level measurements for all modem modes are performed with random transmitted data and without any guard tone. 0dBm = 775mVrms. 0 Note 7 -10 Measured on the 2-wire line with the Tx line signal level set to -10dBm for FSK or single tones, 6dBm and -8dBm for DTMF tones. Excludes any distortion due to external components required for line coupling. Bell 202 -20 -30 dBm -40 -50 -60 -70 10 100 1000 10000 100000 Hz Figure 12 Maximum Out of Band Tx Line Energy Limits (see note 7) © 2008 CML Microsystems Plc 39 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Receive V.23 FSK Mode 1200 baud Acceptable baud rate Mark (logical 1) frequency Space (logical 0) frequency 75 baud Acceptable baud rate Mark (logical 1) frequency Space (logical 0) frequency Notes Min. Typ. Max. Units 1188 1280 2080 1200 1300 2100 1212 1320 2120 Baud Hz Hz 74 382 442 75 390 450 76 398 458 Baud Hz Hz Receive Bell 202 FSK Mode 1200 baud Acceptable baud rate Mark (logical 1) frequency Space (logical 0) frequency 150 baud Acceptable baud rate Mark (logical 1) frequency Space (logical 0) frequency Notes Min. Typ. Max. Units 1188 1180 2180 1200 1200 2200 1212 1220 2220 Baud Hz Hz 148 377 477 150 387 487 152 397 497 Baud Hz Hz Rx Modem Signal Signal level Signal to Noise Ratio (noise flat 300-3400Hz) Notes 10 Min. -45.0 20.0 Typ. - Max. -9.0 - Units dBm dB Rx Modem Continuous 1s and 1010.. Pattern Detectors Turn on time Notes Min. Typ. Max. Units 32 - 40 12 - 20 bittimes bittimes Turn off time Rx Modem Energy Detector Detect threshold (‘Off’ to ‘On) Undetect threshold (‘On’ to ‘Off’) Hysteresis Detect (‘Off’ to ‘On’) response time 1200 baud FSK mode 150 and 75 baud FSK modes Undetect (‘On’ to ‘Off’) response time 1200 baud FSK mode 150 and 75 baud FSK modes Notes 10,11 10,11 10,11 Min. -48.0 2.0 Typ. - Max. -43.0 - Units dBm dBm dB 10,11 10,11 8.0 16.0 - 30.0 60.0 ms ms 10,11 10,11 10.0 20.0 - 40.0 80.0 ms ms Rx Answer Tone Detectors Detect threshold (‘Off’ to ‘On) Undetect threshold (‘On’ to ‘Off’) Hysteresis Detect (‘Off’ to ‘On’) response time Undetect (‘On’ to ‘Off’) response time 2100Hz detector ‘Will detect’ frequency ‘Will not detect’ frequency 2225Hz detector ‘Will detect’ frequency ‘Will not detect’ frequency Notes 10,8 10,8 10,8 10,8 10,8 Min. -48.0 2.0 30.0 7.0 Typ. 33.0 18.0 Max. -43.0 45.0 25.0 Units dBm dBm dB ms ms 2050 - - 2160 2000 Hz Hz 2160 2335 - 2285 - Hz Hz © 2008 CML Microsystems Plc 40 D/860/7 Telephone Signalling Transceiver / Least Cost Router CMX860 Rx Call Progress Energy Detector Bandwidth (-3dB points) See Figure 5a Detect threshold (‘Off’ to ‘On) Undetect threshold (‘On’ to ‘Off’) Detect (‘Off’ to ‘On’) response time Undetect (‘On’ to ‘Off’) response time Notes: Notes 10,9 10,9 10,9 10,9 Typ. 36.0 8.0 Max. 665 -37.0 45.0 50.0 Units Hz dBm dBm ms ms 8. ‘Typical’ value refers to 2100Hz or 2225Hz signal switched between off and -33dBm. Times measured with respect to the received line signal. 9. ‘Typical’ values refers to 400Hz signal switched between off and -33dBm 10. Rx 2-wire line signal level assuming 1dB loss in line coupling components with Rx Gain Control block set to 0dB. 11. Thresholds and times measured with continuous binary ‘1’ for all FSK modes. Fixed compromise line equaliser enabled. Signal switched between off and -33dBm DTMF Decoder Valid input signal levels (each tone of composite signal) Not decode level (either tone of composite signal) Twist = High Tone/Low Tone Frequency Detect Bandwidth Max level of low frequency noise (i.e dial tone) Interfering signal frequency