0402AF-141XJLW

Document 422-1 Chip Inductors – 0402AF Series (1005) • Higher inductance values than other 0402 inductors • Ferrite construction for high current handling • 23 inductance values from 20 nH to 560 nH   Part number1 Impedance typ (Ohms) 900 MHz   1.7 GHz   Inductance2 ±5% (nH) 0402AF-200XJL_ 0402AF-220XJL_ 0402AF-330XJL_ 0402AF-360XJL_ 0402AF-390XJL_ 0402AF-510XJL_ 0402AF-560XJL_ 0402AF-720XJL_ 0402AF-780XJL_ 0402AF-101XJL_ 0402AF-141XJL_ 0402AF-181XJL_ 0402AF-201XJL_ 0402AF-221XJL_ 0402AF-251XJL_ 0402AF-271XJL_ 0402AF-301XJL_ 0402AF-331XJL_ 0402AF-361XJL_ 0402AF-391XJL_ 0402AF-421XJL_ 0402AF-471XJL_ 0402AF-561XJL_ 20 22 33 36 39 51 56 72 78 100 140 180 200 220 250 270 300 330 360 390 420 470 560 83 118 96 146 142 207 157 249 173 263 218 330 239 360 311 453 344 522 513 850 629 949 832 1270 1110 1890 1050 1560 1230 1940 1320 1960 1550 2230 1850 2880 1920 2640 2350 2970 2270 2800 2680 3010 3620 3110   SRF typ3 (MHz) 2600 2500 2300 2300 2200 1930 1900 1650 1600 1400 1220 1150 1000 1150 900 860 860 820 810 760 700 650 600   DCR max4 (Ohms) 0.050 0.065 0.060 0.075 0.115 0.070 0.095 0.100 0.130 0.160 0.260 0.280 0.440 0.530 0.360 0.550 0.410 0.560 0.575 0.750 0.700 0.730 0.920 1. When ordering, please specify termination and packaging codes: Designer’s Kit C397 contains 20 each of all values 0402AF-561XJLW Termination: L = RoHS compliant gold over nickel over silver-palladium-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: W = 7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). Q = 7″ machine-ready reel. EIA-481 punched paper tape (5000 parts per full reel). U = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance measured at 7.9 MHz, 0.1 Vrms, using an Agilent/HP 4286A LCR meter or equivalent with a Coilcraft SMD-F test fixture and Coilcraft-provided correlation pieces. 3. SRF measured using Agilent/HP 8753D network analyzer and Coilcraft SMD­‑D test fixture. 4. DCR measured on Cambridge Technology micro-ohmmeter and a Coilcraft CCF858 test fixture. 5. Current that causes a 15°C temperature rise from 25°C ambient. Because of their open construction, these parts will not saturate. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Core material Ferrite   Irms5 (mA) 1600 1300 1400 1300 830 1100 1000 1000 970 900 630 560 400 380 520 360 420 350 360 300 340 310 200 Terminations  RoHS compliant gold over nickel over silver-palladiumglass frit. Other terminations available at additional cost. Weight  0.9 – 1.1 mg Ambient temperature  –40°C to +85°C with Irms current, +85°C to +100°C with derated current Storage temperature  Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat  Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL)  +25 to +150 ppm/°C Moisture Sensitivity Level (MSL)  1 (unlimited floor life at