0403HQ-9N0XJLU

Document 300-1 Chip Inductors - 0403HQ (1008) • Very high Q factors and excellent current handling • Intermediate L values not found in other series  Inductance2 Percent Q 900 MHz 1.7 GHz  min3  Part number1 (nH) tolerance L typ Q typ L typ Q typ SRF DCR  typ4  max5   Irms6 (GHz) (Ohms) (A) 0403HQ-1N9XJL_ 1.9 0403HQ-2N1XJL_ 2.1 0403HQ-3N4XJL_ 3.4 0403HQ-3N7XJL_ 3.7 0403HQ-5N5XJL_ 5.5 5 5 5 5 5 40 35 40 40 40 0403HQ-6N6XJL_ 6.6 0403HQ-8N2XJL_ 8.2 0403HQ-9N0XJL_ 9.0 0403HQ-12NXJL_ 12 0403HQ-15NXJL_ 15 5 5 5 5 5 40 6.6 60 6.9 40 8.2 63 8.5 40 9.1 66 9.5 40 12.1 60 12.7 35 15.2 60 16.0 0403HQ-18NXJL_ 18 5 35 18.2 62 19.6 93 1. When ordering, please specify termination and packaging codes: 0403HQ-18NXJLW Termination: L = RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: W = 7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). U = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance measured at 500 MHz using a Coilcraft SMD-F fixture in an Agilent/HP 4286 impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured at 500 MHz using an Agilent/HP 4291A with an Agilent/ HP 16193 test fixture. 4. SRF measured using an Agilent/HP 8722ES network analyzer and a test fixture with a 0.017² air gap. 5. DCR measured on a micro-ohmmeter and a Coilcraft CCF858 test fixture. 6. Current that causes a 30°C temperature rise from 25°C ambient. See Qualification Standards section for environmental and test data. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 1.9 62 2.1 56 3.4 66 3.7 64 5.5 62 1.9 2.1 3.5 3.8 5.7 94 11.84 0.012 2.2 88 12.40 0.019 1.8 96 8.97 0.016 1.9 95 8.65 0.018 1.8 93 8.60 0.022 1.5 92 92 90 90 90 7.30 6.73 6.85 5.82 5.82 0.046 0.040 0.055 0.065 0.188 1.1 1.2 1.0 0.80 0.50 5.15 0.185 0.50 Designer’s Kit C371 contains 20 of each value Core material  Ceramic Terminations  RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight  1.29 – 1.60 mg Ambient temperature  –40°C to +125°C with Irms current, +125°C to +155°C with derated current Storage temperature  Component: –40°C to +155°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat  Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL)  +25 to +125 ppm/°C Moisture Sensitivity Level (MSL)  1 (unlimited floor life at