0603AF-821XJEU

Web page Sample & buy Tools & software Support & FAQ Document 773-1 Ferrite Chip Inductors – 0603AF • Higher inductance values than ceramic 0603 inductors • Heavier gauge wire for low DCR • Ferrite construction for high current handling • Inductance values from 15 nH to 10 µH Impedance typ (Ohms)  Inductance2   Part number1 ±5% (nH)  Q typ3 100 MHz   500 MHz 0603AF-15NXJE_ 15 @ 7.9 MHz 0603AF-33NXJE_ 33 @ 7.9 MHz 0603AF-47NXJE_ 47 @ 7.9 MHz 0603AF-72NXJE_ 72 @ 7.9 MHz 0603AF-111XJE_ 110 @ 7.9 MHz 0603AF-121XJE_ 120 @ 7.9 MHz 0603AF-241XJE_ 240 @ 7.9 MHz 0603AF-271XJE_ 270 @ 7.9 MHz 0603AF-361XJE_ 360 @ 7.9 MHz 0603AF-421XJE_ 420 @ 7.9 MHz 0603AF-471XJE_ 470 @ 7.9 MHz 0603AF-561XJE_ 560 @ 7.9 MHz 0603AF-681XJE_ 680 @ 7.9 MHz 0603AF-821XJE_ 820 @ 7.9 MHz 0603AF-102XJE_ 1000 @ 7.9 MHz 0603AF-152XJE_ 1500 @ 7.9 MHz 0603AF-222XJE_ 2200 @ 7.9 MHz 0603AF-472XJE_ 4700 @ 7.9 MHz 0603AF-103XJE_ 10000 @ 2.5 MHz 13@ 7.9 MHz 13@ 7.9 MHz 13@ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15@ 7.9 MHz 11@ 7.9 MHz 15 @ 7.9 MHz 16 @ 7.9 MHz 16 @ 7.9 MHz 16 @ 7.9 MHz 17 @ 7.9 MHz 17 @ 7.9 MHz 16 @ 2.5 MHz 16 @ 7.9 MHz 12 @ 2.5 MHz 10 19 42 60 70 76 140 173 210 250 306 371 420 507 663 944 5220 2100 1400 1. When ordering, please specify termination and packaging codes: 0603AF-102XJEW Termination: E = Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: R = RoHS compliant matte tin over nickel over silver-platinum-glass frit Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37). Packaging: W = 7″ machine-ready reel. EIA-481 punched paper tape (2000 parts per full reel). U = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter W instead. 2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture in Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture. 4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft SMD‑D test fixture. 5. DCR measured on Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. Because of their open construction, these parts will not saturate. This information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Each part is marked with a single dot. The color dots are not unique identifiers and correspond to multiple inductance values. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. typ4  DCR max5   Irms6 Color (MHz) (Ohms) (A)  code7    SRF 42 90 210 385 350 410 810 1023 1310 1925 2253 3180 3620 3300 9823 17,830 129 220 150 3500 2300 2250 1800 1230 1150 900 750 700 685 575 515 530 325 400 330 85 60 40 0.023 0.028 0.052 0.065 0.060 0.089 0.12 0.22 0.21 0.33 0.37 0.49 0.46 0.58 0.84 1.30 1.10 1.50 4.50 2.1 1.9 1.7 1.5 1.6 1.4 0.85 0.68 0.65 0.61 0.61 0.53 0.49 0.42 0.40 0.28 0.32 0.26 0.18 Yellow Red White Blue Red Black Violet Brown Blue Red Orange Blue Orange Green Black Orange Red Yellow Gray Designer’s Kit C439 contains 10 each of all values Core material Ferrite Environmental  RoHS compliant, halogen free Terminations  RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost Weight  4.3 – 5.7 mg Ambient temperature  –40°C to +85°C with Irms current Maximum part temperature  +100°C (ambient + temp rise) Derating. Storage temperature  Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat  Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL)  +50 to +300 ppm/°C Moisture Sensitivity Level (MSL)  1 (unlimited floor life at