0805HP-391XGRC

Document 1362-1 Chip Inductors – 0805HP (2012) • Exceptional Q values, even at high frequencies • Tight tolerances – 2% for most   Part number1 0805HP-2N6XJR_ 0805HP-6N2XJR_ 0805HP-6N8XJR_ 0805HP-11NX_R_ 0805HP-12NX_R_ 0805HP-13NX_R_ 0805HP-18NX_R_ 0805HP-33NX_R_ 0805HP-47NX_R_ 0805HP-56NX_R_ 0805HP-82NX_R_ 0805HP-101X_R_ 0805HP-121X_R_ 0805HP-151X_R_ 0805HP-181X_R_ 0805HP-221X_R_ 0805HP-271X_R_ 0805HP-331X_R_ 0805HP-391X_R_ 0805HP-471X_R_ 0805HP-561X_R_ 0805HP-681X_R_ 0805HP-821X_R_   Inductance2 (nH) 2.6 @ 250 MHz 6.2 @ 250 MHz 6.8 @ 250 MHz 11 @ 250 MHz 12 @ 250 MHz 13 @ 250 MHz 18 @ 250 MHz 33 @ 250 MHz 47 @ 200 MHz 56 @ 200 MHz 82 @ 150 MHz 100 @ 150 MHz 120 @ 150 MHz 150 @ 100 MHz 180 @ 100 MHz 220 @ 100 MHz 270 @ 100 MHz 330 @ 100 MHz 390 @ 100 MHz 470 @ 50 MHz 560 @ 25 MHz 680 @ 25 MHz 820 @ 25 MHz • Wirewound construction for highest possible self resonance – up to 9.5 GHz Percent   SRF typ5   DCR max6   Irms7 (MHz) (Ohms) (A)   tolerance3   Q typ4 5 5 5 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 100 @ 1500 MHz 104 @ 1000 MHz 90 @ 1000 MHz 93 @ 500 MHz 91 @ 500 MHz 91 @ 500 MHz 95 @ 500 MHz 100 @ 500 MHz 105 @ 500 MHz 100 @ 500 MHz 103 @ 500 MHz 100 @ 500 MHz 80 @ 250 MHz 80 @ 250 MHz 77 @ 250 MHz 75 @ 250 MHz 75 @ 100 MHz 54 @ 100 MHz 52 @ 100 MHz 52 @ 100 MHz 46 @ 100 MHz 46 @ 100 MHz 50 @ 100 MHz 1. When ordering, specify tolerance, termination and packaging codes: 0805HP-821XJRC Tolerance: G = 2%  J = 5% Termination: R = RoHS matte tin over nickel over silver-platinum-glass frit Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) over tin or P = non-RoHS tin-lead (63/37) over tin. Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel). 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/ HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Tolerances in bold are stocked for immediate shipment. 4. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 5. SRF measured using an Agilent/HP 8720D network analyzer and a Coilcraft SMD­‑D test fixture. 6. DCR measured on a Cambridge Technology micro-ohmmeter and a Coilcraft CCF858 test fixture. 7. Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 9500 7200 6000 4750 4425 4100 3650 2410 2170 1815 1525 1400 1265 1150 1025 930 830 770 700 640 550 535 485 0.015 0.027 0.066 0.039 0.039 0.039 0.050 0.087 0.093 0.122 0.168 0.220 0.293 0.288 0.374 0.426 0.754 1.004 1.110 1.559 2.067 2.355 3.945 2.0 1.5 1.3 1.6 1.4 1.4 1.2 1.1 1.0 0.95 0.82 0.72 0.62 0.60 0.54 0.50 0.42 0.36 0.33 0.28 0.24 0.21 0.18 Core material Ceramic Environmental  RoHS compliant, halogen free Terminations  RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost. Weight  9.5 – 12.5 mg Ambient temperature  –40°C to +125°C with Irms current Maximum part temperature  +140°C (ambient + temp rise). Storage temperature  Component: –40°C to +140°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat  Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL)  +100 to +250 ppm/°C Moisture Sensitivity Level (MSL)  1 (unlimited floor life at