1008LS-183XJLB

Document 103-1 Chip Inductors – 1008LS (2520) • Lower DCR than other 1008 inductors • Ferrite construction for high current handling • Inductance values: 1.0 – 100 µH   Part number1   Inductance2 (µH) 1008LS-102XJL_    1.0 @ 7.9 MHz 1008LS-122XJL_    1.2 @ 7.9 MHz 1008LS-152XJL_    1.5 @ 7.9 MHz 1008LS-182XJL_    1.8 @ 7.9 MHz 1008LS-222XJL_    2.2 @ 7.9 MHz 1008LS-272XJL_    2.7 @ 7.9 MHz 1008LS-332XJL_    3.3 @ 7.9 MHz 1008LS-392XJL_    3.9 @ 7.9 MHz 1008LS-432XJL_    4.3 @ 7.9 MHz 1008LS-472XJL_    4.7 @ 7.9 MHz 1008LS-502XJL_    5.0 @ 7.9 MHz 1008LS-562XJL_    5.6 @ 7.9 MHz 1008LS-622XJL_    6.2 @ 7.9 MHz 1008LS-682XJL_    6.8 @ 7.9 MHz 1008LS-822XJL_    8.2 @ 7.9 MHz 1008LS-912XJL_    9.1 @ 7.9 MHz 1008LS-103XJL_   10 @ 7.9 MHz 1008LS-123XJL_   12 @ 2.5 MHz 1008LS-153XJL_   15 @ 2.5 MHz 1008LS-183XJL_   18 @ 2.5 MHz 1008LS-223XJL_   22 @ 2.5 MHz 1008LS-273XJL_   27 @ 2.5 MHz 1008LS-333XJL_   33 @ 2.5 MHz 1008LS-393XJL_   39 @ 2.5 MHz 1008LS-473XJL_   47 @ 2.5 MHz 1008LS-563XJL_   56 @ 2.5 MHz 1008LS-683XJL_   68 @ 0.79 MHz 1008LS-104XJL_ 100 @ 0.79 MHz Request free evaluation samples by contacting Coilcraft or visiting www.coilcraft.com.   SRF min4   DCR max5   Irms6 Percent   Q min3 (MHz) (Ohms) (mA)   tolerance 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 1. When ordering, please specify termination and packaging codes: 1008LS-103XJLC Termination: L = RoHS compliant silver-palladium-platinum-glass frit. E = Halogen free component. RoHS compliant silverpalladium-platinum-glass frit terminations. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel). 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/ HP 4286A impedance analyzer with Coilcraft-provided correlation pieces. 3. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test fixture. 4. SRF measured using an Agilent/HP 8753D network analyzer with a Coilcraft SMD-D fixture. 5. DCR measured on a Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C. Because of their open construction, these parts will not saturate. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. For part marking data visit http://www.coilcraft.com/colrcode.cfm. 48 @ 50 MHz 37 @ 50 MHz 37 @ 50 MHz 37 @ 50 MHz 37 @ 50 MHz 37 @ 50 MHz 37 @ 50 MHz 37 @ 7.9 MHz 30 @ 7.9 MHz 32 @ 7.9 MHz 25 @ 7.9 MHz 37 @ 7.9 MHz 32 @ 7.9 MHz 37 @ 7.9 MHz 37 @ 7.9 MHz 37 @ 7.9 MHz 37 @ 7.9 MHz 28 @ 2.5 MHz 34 @ 2.5 MHz 28 @ 2.5 MHz 20 @ 2.5 MHz 24 @ 2.5 MHz 22 @ 2.5 MHz 33 @ 2.5 MHz 20 @ 2.5 MHz 20 @ 2.5 MHz 14 @ 0.79 MHz 13 @ 0.79 MHz 230 210 190 170 150 135 120 105 85 90 30 80 75 70 65 57 60 38 30 26 22 12 19 26 12 8.0 5.7 4.5 0.62 0.68 0.76 0.84 1.10 1.28 1.46 1.56 1.70 1.68 2.20 1.82 2.50 2.00 2.65 2.90 2.95 3.30 3.70 4.00 6.14 6.45 7.00 10.0 10.7 10.0 13.5 20.5 700 650 630 600 520 490 450 420 400 400 360 380 330 360 330 310 300 290 280 160 270 210 200 170 160 170 145 120 Designer’s Kit C336 contains 10 of each stocked value Core material Ceramic/Ferrite Environmental  RoHS compliant, halogen free optional Terminations  RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight  38.3 – 41.0 mg Ambient temperature  –40°C to +85°C with Irms current, +85°C to +100°C with derated current Storage temperature  Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat  Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL)  +100 to +350 ppm/°C Moisture Sensitivity Level (MSL)  1 (unlimited floor life at