5315TC-715XGL

Document 311 -1 RFID Transponder Coils – 5315TC The 5315TC is Coilcraft’s most rugged and lowest cost antenna coil designed for RFID applications at 125 kHz. The wrap-around terminals have large mounting surfaces to ensure excellent board adhesion. The coil is wound on a plastic base, providing great durability and allowing this part to withstand harsh mechanical shock. Their robust construction and 125°C rating make these parts suitable for use in the most severe environments. They were developed for automotive applications, including tire pressure monitoring systems. In addition to the standard models shown, Coilcraft can design transponder coils to operate at other frequencies. Coilcraft Designer’s Kit C369 contains four samples each of the standard parts shown. To order, contact Coilcraft or visit http://order.coilcraft.com. Part number1 5315TC-374XGL_ 5315TC-404XGL_ 5315TC-704XGL_ 5315TC-904XGL_ 5315TC-105XGL_ 5315TC-115XGL_ 5315TC-205XGL_ 5315TC-245XGL_ 5315TC-335XGL_ 5315TC-415XGL_ 5315TC-495XGL_ 5315TC-685XGL_ 5315TC-715XGL_ 5315TC-725XGL_ Inductance2 at 125 kHz ±2% (mH) 0.37 0.40 0.70 0.90 1.00 1.08 1.97 2.38 3.30 4.15 4.90 6.80 7.10 7.20 Q min2 8 8 12 12 12 13 14 12 14 15 15 13 14 17 Read distance3 (inches/cm) 16 / 40.6 17 / 43.2 21 / 53.3 21 / 53.3 23 / 58.4 23 / 58.4 25 / 63.5 26 / 66.0 27 / 68.6 29 / 73.7 28 / 71.1 30 / 76.2 30 / 76.2 30 / 76.2 Sensitivity4 (mV/µT) 8.32 8.67 11.43 13.35 14.07 14.65 21.28 23.97 29.70 34.95 40.00 53.87 55.41 56.74 Matching capacitor5 (pF) 4380 4050 2320 1800 1600 1500 820 680 490 390 330 240 220 220 DCR max6 (Ohms) 24 25 33 38 40 40 70 80 95 103 150 180 176 165 SRF typ7 (kHz) 7100 7300 4500 3800 2500 2300 2300 2400 1800 1260 1550 1350 890 880 1. When ordering, please specify packaging code: 5315TC-715XGLD Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic tape (3000 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance and Q measured using Agilent/HP 4192A impedance analyzer at 125 kHz. For recommended test procedures, contact Coilcraft. 3. Read distance measured using the KEELOQ® Transponder Evaluation Kit part number DM303005 from Microchip. Distance was recorded as the voltage across the resonant circuit dropped below 10 mV. 4. Sensitivity measured in accordance with Coilcraft application note “Measuring Sensitivity of Transponder Coils.” 5. Matching capacitor value required for parallel resonant circuit operating at 125 kHz. 6. DCR measured on micro-ohmmeter. 7. SRF measured using Agilent/HP 8753D network analyzer. 8. Ambient temperature range: –40°C to +125°C 9. Storage temperature range: Component: –40°C to +125°C Packaging: –40°C to +80°C 10. Resistance to soldering heat: Three reflows at >217°C for 90 seconds (+260°C ±5°C for 20 – 40 seconds), allowing parts to cool to room temperature between. 11. Electrical specifications at 25°C. 12. Temperature coefficient of inductance: +300 to +1100 ppm/°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. Document 311-1 Revised 02/19/09 © Coilcraft, Inc. 2009 Document 311-2 RFID Transponder Coils – 5315TC Typical L vs Frequency 14 12 Dimensions 0.536 13,61 0.15 3,81 Inductance (mH) 10 8 -725 XXX 0.10 ±0.002 2,54 ±0,05 -415 6 4 2 0 10 100 1000 10000 0.089 max 2,26 0.10 2,54 0.33 8,38 -115 -404 Unless specified, tolerance is ±0.010 (±0,25). 0.56 14,22 Frequency (kHz) 0.16 4,06 0.12 3,05 0.32 8,13 Recommended Land Pattern Terminations Gold over nickel over phos bronze Weight 260 – 300 mg Packaging 3000/13″ reel; Plastic tape: 24 mm wide, 0.3 mm thick, 8 mm pocket spacing, 2.74 mm pocket depth Specifications subject to change without notice. Please check our website for latest information. Document 311-2 Revised 02/19/09 © Coilcraft, Inc. 2009